Heated Seats
This system allows the electrical heating of the front seats on passenger demand.
The components of the system are:
- the seat heating elements located in the seat cushion and backrest.
- the heated seat control switch, located on the seat side trim panel.
- temperature sensors located in the seat cushion heating elements.
- heated seat relay.
Do both front seat heaters not work ? Do you know how to test electrical circuits with voltmeter ?
PINPOINT TEST J: THE HEATED SEAT IS INOPERATIVE
Test Step
Result / Action to Take
J1 CHECK HEATED SEAT SWITCH OPERATION
- Key in ON position.
- Press the heated seat switch on the driver and passenger seats.
- Are both heated seat switch indicators illuminated?
Yes
If both indicators illuminate, Go To Pinpoint Test K . If only one indicator illuminates, GO to J5 .
No
GO to J2 .
J2 CHECK THE HEATED SEAT RELAY CIRCUITS
- Key in OFF position.
- Disconnect: Heated Seat Relay C3250 (located under the driver seat).
- Key in ON position.
- Measure the voltage at heated seat relay C3250-86, circuit 1003 (GY/YE), harness side and ground; and between C3250-30, circuit 566 (DG), harness and ground.
- Are the voltages greater than 10 volts?
Yes
GO to J3 .
No
REPAIR inoperative 1003 (GY/YE) or 566 (DG) circuit. TEST the system for normal operation.
J3 CHECK HEATED SEAT RELAY GROUND CIRCUIT
- Key in OFF position.
- Measure the resistance between heated seat relay C3250-85, circuit 57 (BK), harness side and ground.
- Is the resistance less than 5 ohms?
Yes
GO to J4 .
No
REPAIR circuit 57 (BK). TEST the system for normal operation.
J4 CHECK THE HEATED SEAT RELAY
- Install a fused jumper lead between heated seat relay 3250-30, circuit 566 (DG), harness side and heated seat relay C3250-87, circuit 1064 (YE/LB), harness side.
- Do both heated seat indicators illuminate when pressed?
Yes
INSTALL a new heated seat relay. TEST the system for normal operation.
No
REPAIR circuit 1064 (YE/LB) to switches. TEST the system for normal operation.
J5 CHECK INOPERATIVE HEATED SEAT SWITCH INPUT
- Key in OFF position.
- Disconnect: Heated Seat Switch C320 (Driver) or C321 (Passenger) for the inoperative heated seat.
- Key in ON position.
- Measure the voltage between heated seat switch C320-2 (driver) or C321-2 (passenger), circuit 1064 (YE/LB), harness side and ground .
- Is the voltage greater than 10 volts?
Yes
GO to J6 .
No
REPAIR circuit 1064 (YE/LB). TEST system for normal operation.
J6 CHECK CIRCUIT 57 (BK) FOR AN OPEN
- Measure the resistance between heated seat switch C320-4 (driver) or C321-4 (passenger), circuit 57 (BK), harness side and ground.
- Is the resistance less than 5 ohms?
Yes
INSTALL a new heated seat switch. TEST the system for normal operation.
No
REPAIR circuit 57 (BK). TEST the system for normal operation
It's not that simple , being a fuse . It's probably the relay or the heating element .
PINPOINT TEST K: SEAT DOES NOT HEAT BUT THE HEATED SEAT INDICATOR ILLUMINATES WHEN PRESSED ? Does it ?
Your best bet would be to take to a qualified repair shop .
Do
HI I HAVE JUST BOUGHT A 1999 ON A V-PLATE 2.5V6 24v .IT HAS HEATED FRONT SEATS BUT MINE AS THE DRIVER DOESNT WORK JELOUS MY WIFES SEAT IS NICE AND WARM THE LIGHT ON THE SWITCH WORKS BUT SEAT DOESNT HEAT UP ANY IDEAS .ALSO THERE IS A WEIRD NOISE IN THE ENGINE WHEN I CHANGE GEAR IT SOUNDS AS IF IT IS OVER REVING IVE BEEN TOLD ITS CALLED THROTTLE HANG COULD YOU PLEASE SORT OUT MY PROBLEMS REGARDS ANDREW HARRIES.
Believe or not its under the seats need to take out the seat if you need more info go to collsionrepairadvice.com
×