Question about 1998 Jeep Cherokee

1 Answer

PO137 02 sensor of 1998 grand cherokee

Locate the PO137 sensor of grand cherokee

Posted by on

Ad

1 Answer

Google it & read up

Oxygen Sensor Code

Codes don't tell you what to replace,
have use code to diagnose the fault

Posted on Mar 27, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

  • 285 Answers

SOURCE: crankshaft sensor located 98 jeep grnd cher 4wd 6cy

it is located at the back of the engine on top of the transmission bell housing,the plug runs over to the passenger side of the engine bay and it comes out from behind the engine,you can actually get your hand on the sensor itself from under the hood on the drivers side,and i believe its a 13mm bolt holding it in,the new sensor will have a sticker on the end of it...leave it there,it is used for correct spacing between the sensor and the flywheel,hope this helps

Posted on Sep 23, 2009

Testimonial: "Everything was just like you said but as a not atleast for my jeep it is an 11mm not 13mm. Works great so far (keep fingers crossed) "

emissionwiz
  • 85206 Answers

SOURCE: IAT sensor location

here is a picture


0d597dc.jpg

Posted on Mar 09, 2010

  • 30 Answers

SOURCE: fuel filter location 1998 jeep grand cherokee

The fuel filter sits on top of the fuel pump. It is the fuel fuel filter/fuel pressure regulator. You will have to drop the gas tank to access it. Hope this helps.

Best of luck

Posted on Jun 19, 2010

emissionwiz
  • 85206 Answers

SOURCE: location of cam sensor 2003 jeep grand cherokee v8

Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Posted on Jul 21, 2010

Testimonial: "that is just what i needed thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How many o2 sensors on a 2003 buick rendezvous?


If your vehicle has single exhaust, there are two oxygen sensors.

If your vehicle has dual exhaust, there are four oxygen sensors.

Aug 01, 2014 | 2003 Buick Rendezvous

1 Answer

Where is the speed sensor at on a 1993 jeep grand cherokee


On 1993 Jeep Grand Cherokee 4WD 5.2L MFI 8cyl the Vehicle Speed Sensor - is located in Transmission / Transfer case extension housing (tail section), near where the drive shaft attaches to the transmission. The sensor has three wires (white / black, black / light blue and white / orange).

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 15, 2011 | 1993 Jeep Grand Cherokee

1 Answer

Where is crank shaft position sensor located on 1997 jeep grand cherokee


CRANKSHAFT POSITION SENSOR LOCATION FOR 4.0L ENGINE IS ON TRANSMISSION BELLHOUSING AT THE LEFT REAR OF THE ENGINE. FOR 5.2L ENGINE CRANKSHAFT SENSOR LOCATED ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Dec 11, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Locate crank shaft sensor on 1998 jeep grand cherokee


4.7L ENGINE CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK ABOVE THE STARTER. ON THE 4.0L ENGINE CRANKSHAFT SENSOR LOCATED TRANSMISSION BELL HOUSING AT THE LEFT REAR OF THE ENGINE. THE 5.2L 5.9L CRANKSHAFT SENSOR LOCATED ON THE ENGINE BLOCK BEHIND THE RIGHT CYLINDER HEAD.

Nov 26, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Location of cam sensor 2003 jeep grand cherokee v8


Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Jul 21, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Location of coolant sensor for 97 Jeep Grand Cherokee v8


in the 5.2L V8 engine the coolant sensor is located on top of the engine. Locate the coolant thick hose coming from top of the ratiator to the top of the engine. Look at the place such hose connects to the engine you wont miss the sensor it is about one inch from there.

Jun 27, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Need to find where o2 sensor is located on jeep gran cherokee 93


You have one O2 sensor, this is the location...

27bd250.jpg

Also can check your 1993 Grand Cherokee Repair Manual

Hope this help (remember rated this), good luck.

Feb 08, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Where is the map sensor located? 1994 jeep grand cherokee


Go half way between the air cleaner box and the "carburetor". Up the 4" black air pipe, a wire harness plug plugs into the MAP sensor there. Also called MAS air flow sensor.

Oct 05, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Where's the output transmi. sensor on a 2000 Jeep Grand Cherokee?


if you mean speed sensor it is located on reductor where shaft comes out to rear dif. if you mean rpm sensor, it is located on top of transmition screwed vith two bolts in cilinder block.
marko

Aug 11, 2009 | 2000 Jeep Cherokee

Not finding what you are looking for?
1998 Jeep Cherokee Logo

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...