Where is the relay and fuse for the fuel pump on a 1996 Nissan Quest?
The fuel pump relay is in the black box under the hood by the battery. #22 (fuel pump - PCM) & #27 (fuel pump) are for the fuel pump.
It says there is a 15 amp fuel pump circuit fuse in the interior fuse panel on the dash panel by the drivers knee location. I could not find it but here is the picture.
SOURCE: fuel pump removal
Replace Fuel Pump for 1997 Nissan Quest
(1) If the fuel tank has more than one third full, you need to get the gasoline out. If it has one third or less full, you can leave it in the tank. However be very careful around the working area. Make sure you have read fire precautions in a general repair book. Take the fuel pump fuse out from the fuse box near the battery. Run starter for a few seconds. This will remove the fuel pressure in the gas lines. Disconnect battery at negative terminal. Jack up the rear of the van.
(2) Remove the fuel tank protector.
(3) Disconnect fuel pipes at the front end of the fuel tank. Use short pencils and extra rubber hoses to block disconnected pipes and hoses.
There are two pipes connected to the gasoline filler at the side of the van. Disconnect only the smaller one. The larger one is flex enough for the tank to be lowered.
(4) Disconnect the electrical from this connector. Jack the rear end of the fuel tank with a car jack and a piece of 2x4. Put the wood between the jack point and the tank. Then unbolt the two bolts showing in the picture.
(5) Lower the jack after the bolts are removed. The rear end of the tank should be lowered.
(6) Disconnect fuel lines on top of the fuel pump. Reconnect each short hose back to different pipes as shown in picture to block the pipes.
(7) Loose the six mounting bolts on the fuel pump assembly. The bolts should be loosen a little at a time in multiple turns. Also detach the electrical wire holders. After all bolts are removed, carefully take the assembly out of the tank.
(8) Remove the fuel pump from the assembly as shown in picture. Then unplug the electrical wires. Note that two connectors are in different sizes, so that you will not be able to reconnect to a wrong terminal.
(9) Put the new pump and new filter in. Reconnect the electrical wires. If necessary use a pair of pliers to make the connectors tighter. Make sure they are not loose. Reconnect gas inlet to the pressure regulator.
(10) Use a new O ring, put back the assembly to the fuel tank. Make sure the float of the fuel level senser is free, and the assembly is at the right orientation (as shown in picture). Screw back the 6 bolts after making sure the O ring is in right place. The bolts should be tightened in turns. Do not over tighten them. Then reconnect the fuel lines and make sure every fastener is tight. Put the electrical wire into holders.
(11) Jack up the tank and put the two mounting bolt in. (see picture in step 4). Make sure they are tightened with specific torque. Reconnect the electrical connector.
(12) Reconnect two fuel lines at the front side of the tank. Refer to the picture in step 2. Reconnect the hose to the gasoline filler. Before you have a try start, double check if all fuel lines are securely connected and tightened.
(13) Start the engine. You need to crank more than a normal start because the lines were empty. The pressure is built up in some time.
(14) If engine starts ok, turn it off. Then check under the van if there is any leakage. If everything is fine put back the tank protector. (picture in step 2).
SOURCE: 1996 windstar relay
The fuel pump power on the Windstar is controlled by a component called a Constant Control Relay Module (CCRM).
Its located located on the driver's side of the engine compartment.
SOURCE: fuel pump relay location
dfifrank: The relay you are seeking is locate on the driver's side of the car. The left kick panel or panel forward of the left front door pillar. There is a large box which is the ABS control unit.
There are two smaller relays with it. The relay mounted which is closest to the rear of the car is the fuel pump relay.
The relays in the fuse panel are as follows: the one to the extreme left which is located half way up the box is the ignition relay.
The one at the top right is the accessory relay and the one at the bottom right is the blower relay.
You have a pair of audio amp relay's located in the right lower kick panel and a flasher unit sometimes referred to as a relay, located further up closer to the firewall on the right kick panel.
I believe this should answer your questions and then some.
I service a lot of Maxima's consequently they are somewhat familiar to me.
SOURCE: i need to change the water pump on my nissan Quest
Hello and thank you for using FixYa!
To replace the water pump, the front engine timing belt would need to be removed. This is a very big job and should be done by someone who is familiar with how timing belt jobs are done.
Thanks Jay!
4,302 views
Usually answered in minutes!
×