At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Remove the plastic triangular trim piece behing the mirror on the inside, it just pops off, you will three 10mm nuts, remove them and pull the mirror off, you'll have to disconnect the electrical connector if it's a powered mirror.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1.call the chrysler dealership for a new replacement or call around to autowreckers for one. 2.open the door. 3.pry off plastic from door to mirror spindle. 4.check wiring coloring. 5. pull off plastic under steering wheel may be held on by 2 or 3 screws. 6.locate wiring from mirror under dash. 7.unplug wiring harness for mirror. 8.pull out old wiring. 9.remove old mirror with old wiring harness. 10. replace with new mirror and wiring harness and then repeat.
Well, technically you dont have to remove the door panel to remove the outside door mirror. At the top of the door panel, at the front of the door, there is a triangle shaped plastic cover. It's held in place with push clips, so pull that cover off and remove the foam insulation and you'll be able to access the 3 nuts that hold the mirror to the door. The only potential problem could be in unplugging the wiring harness. I use a hooked pick to pull up the harness to unplug it.
Step 1 Disconnect the negative battery cable before you take off the grand Cherokee front door trim panel. Remove all screws and clips.
Step 2 Detachthe window trim cover screw, and control lever screw beforedisconnecting the entire mirror trim cover. Remove the rubber coverinside the mirror cover, and disconnect the electrical wire.
Step 3 Remove three nuts from the power mirror using a Torx® star-shaped screwdriver.
Step 4 Pull out the outside rear view mirror. Guide the power wire through the hole in the door.
Install the New Mirror
Step 1 Replace the old mirror. Put the new power mirror in place. Push the new wiring through the hole in the door.
Step 2 Install and tighten the three retaining screws you took off when removing the old mirror.
Step 3 Connect the power mirror wiring to the connection located on the door panel. Replace the rubber cover and interior mirror cover.
Step 4 Put the front door trim panel back in place by securing all clips and tightening all screws.
Step 5 Connect the Subaru Outback's battery cable to restore the power.
i will recommend i site where you will get all the information you need to remove and replace your side mirror http://www.wjjeeps.com/mirrors.htm
You'll need to remove screws that are by the door handle,
arm rest, under door and side of door and then gently pull back on the
panel as there will also be retaining clips attached and you don't want
to break them. Then you can access the mirror assembly.. it's a huge pain to change such a small part
You need to put on a pair of gloves, and safety glasses. (Safety First !) Prise off the broken mirror from the plastic base that it is stuck too.
Give the plastic a clean with nail polish remover or similar.
Peel off the backing on new mirror glass, and carefully stick it on.
the inner cover (the one on your side) goes off by pushing it upwards , then ull find 3 screws, 8 or 9 mm, take the off, unplug the electrical connection and the old mirror should come off fairly easy, replace, redo the invert process hope this helps have fun
Behind the passenger-side front-door at the bottom of the window you will find a molded triangular panel with a tweeter [audio speaker]. To access the nuts that affix the side-view mirror to the door you will remove the panel. Gently pry on the top of the panel to remove it but be careful as speaker wires will be attached. Quick way to replace the mirror assembly is to support the panel and don't put stress on the wires. Open the door and find the nuts that hold the mirror onto the door. If you have electric powered mirrors you will need to separate the connector that sends current to the mirror for the remote function. Remove the nuts and be very careful not to drop the nuts into the door cavity. Good luck!
If you need to replace the entire mirror - it's a little involved. First you need to take the upper extension panel off from behind the mirror (black triangle) - just pull it of starting at the top. It will snap back on later. Next - remove the different screws holding the door panel in place (not the ones behind the mirror yet!) One is under the handle (pull it out and pull out the filler panel - small plastic thing that has a hole to pry it out). Then take off the rear red light - also pops off - and remove that screw. Finally - pick up the rubber filler where your fingers pull the door shut and remove these torx bolts.
Now is the tricky part. Snapp off the entire interior panel. It will pop off - but very difficult. It will sound like it is breaking! Start at the outer bottom corner - and use a door panel remover tool - check Amazon or E-bay - to keep from breaking things. Pull it out from all around the bottom and sides and then lift it up over the door lock. It good to have a friend help here. The panel will still be held on by a cable - that is your door release - leave it alone and let the panel hang by it (or better, put a box under it to rest on).
Now...remove the three bolts holding the mirror on - have a friend help hold the mirror while you do this or it will scratch your new car! Since the inner panel is off - you can also disonnect the mirror plus and remove it. It sounds silly - but the only reason to remove the door panel is to unplug it!
Get you new mirror and reverse the steps.
If you are just replacing the glass (non-heated) - get a replacement from the dealer. Adjust the mirror all the way to the inside and reach behind and pop it off. CAREFUL - put tape over the entire glass as it will likely break even more! Remove your connectors if heated - and replace (and reconnect) with your new glass. It just pops back on!
Replacing glass is easy - just be careful of cheap imitations on e-abay). And never use cheap flat glass on the passenger side! The DOT has special requirements for mirror glass - buy it from gmpartsdirect.com or your local dealer.
On the inside trim, you can remove screws that are by the door handle,
arm rest, under door and side of door and then gently pull back on the
panel as there will also be retaining clips attached and you don't want
to break them. You'll need to lift the door panel upwards in order to
get it off the window ledge. Then you'll need to manipulate the panel
and disconnect the door handle linkage from the door handle and
disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door
×