Question about Jeep Wrangler

Open Question

Where is the pdc located on an 89 jeep wrangler

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: fuse box

Under the left of the dash board close to the parking brake tucked up under.

Posted on Feb 15, 2009

Ad
  • 6982 Answers

SOURCE: location/testing of crank sensor 1995 jeep wrangler

Should be on the bellhousing on the drivers side just where you need rubber arms to reach it.Should have no continuity between b&c terminals (check with ohmeter) Harness plug is usually on the drivers side between the master cyl and the back of the engine (unless someone moved it)

Posted on Apr 14, 2009

ZJLimited
  • 17970 Answers

SOURCE: how do you replace the distributor on an 89 jeep

Jeep Wrangler/YJ 1987-1995 Repair Guide

DISTRIBUITOR

REMOVAL & INSTALLATION

2.5L Engine
1987-90 VEHICLES
See Figures 1, 2, 3 and 4

5686591.gif


Fig. 1: Exploded view of the distributor-1987-90 2.5L engine


0d487c5.gif



Fig. 2: Positioning the oil pump shaft for distributor installation-1987-90 2.5L engine


506ca58.gif



Fig. 3: Positioning the distributor rotor and shaft for installation-1987-90 2.5L engine


85b810b.gif





Fig. 4: Rotor position with the distributor properly installed-1987-90 2.5L engine




  1. Disconnect the negative battery cable.
  2. Remove the primary lead from the terminal post at the side of the distributor.

The wire connector will contain a special conductive grease. Do not remove it. The same grease will also be found on the metal parts of the rotor.
  1. Disconnect the vacuum line if there is one.
  2. Remove the two distributor cap retaining hooks or screws and remove the distributor cap.
  3. Note the position of the rotor in relation to the base. Scribe a mark on the base of the distributor and on the engine block to facilitate reinstallation. Align the marks with the direction the metal tip of the rotor is pointing.
  4. Remove the bolt that holds the distributor to the engine.
  5. Lift the distributor assembly from the engine.

To install, if engine was not disturbed:
  1. Insert the distributor shaft and assembly into the engine. Line up the mark on the distributor and the one on the engine with the metal tip of the rotor. Make sure that the vacuum advance diaphragm is pointed in the same direction as it was pointed originally. This will be done automatically if the marks on the engine and the distributor are line up with the rotor.
  2. Install the distributor hold-down bolt and clamp. Leave the screw loose enough so that you can move the distributor with heavy hand pressure.
  3. Connect the primary wire to the distributor side of the coil. Install the distributor cap on the distributor housing. Secure the distributor cap with the spring clips or the screw type retainers, whichever is used.
  4. Install the spark plug wires. Make sure that the wires are pressed all of the way into the top of the distributor cap and firmly onto the spark plugs.

If the engine was turned while the distributor was removed, or if the marks were not drawn, it will be necessary to initially time the engine. Follow the procedure below.
To install, if engine was disturbed:
  1. Rotate the engine until the No.1 piston is at TDC compression.
  2. Using a flat bladed screwdriver, in the distributor hole, rotate the oil pump gear so that the slot in the oil pump shaft is slightly past the 3:00 o'clock position, relative to the length of the engine block.
  3. With the distributor cap removed, install the distributor with the rotor at the 5:00 o'clock position, relative to the oil pump gear shaft slot. When the distributor is completely in place, the rotor should be at the 6:00 o'clock position. If not, remove the distributor and perform the entire procedure again.
  4. Tighten the lockbolt.



Remember rated this post; I hope help you with this.










Posted on Aug 21, 2009

Testimonial: "Extremely helpful!"

  • 5 Answers

SOURCE: 89 Jeep Wrangler. Engine stalls only when I put into gear.

it might be getting to much fuel check the fuel screw

Posted on Sep 11, 2009

  • 437 Answers

SOURCE: 2001 jeep Tj pdc diagram trying to locate fuse for

sounds like it is either flasher or switch assembly.

Posted on Oct 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My power outlet beside cig lighter quit working I can't locate the fuse for it 2004 jeep wrangler.


both 20amp
F17 is in PDC(under hood)
F18 is in cab box. (answer assumes car starts and drives)
26223724-1nshu3pptitflaomei2asm0z-1-0.jpg

Jun 22, 2016 | Jeep Cars & Trucks

1 Answer

Where is the radiator fan relay on a 2012 jeep wrangler


I guess reading the lids on fuse box, too hard?
yet another endless easter egg hunt and zero symptoms, wow.
in the fuse box.,
eg< u guess, i point, u guess i point...wash and repeats.

if it has one,,, you do know jeep is removing them year by year , right, relays are going bye-bye.... one by one...
like we did in industry for 30 years now.
i own a JK 08 with full fsm.
mine has 3,
2 in the TIPM under hood,
and one more by self in left front of engine.
and has complex rules in the PCM software. to run it.
based on engine temp and a/c rules.
complex.
im at mitchells now , looking for you.

2013
quote
The electric cooling fan HI and LOW relays are located in the Power Distribution Center (PDC) in the engine compartment. See the fuse and relay layout label affixed to the inside surface of the PDC cover for cooling fan relay identification and location.
The HI and LOW cooling fan relays cannot be adjusted or repaired. If the HI or LOW relay is damaged or faulty, it must be replaced.
(i thinks this data above uses wrong names for the box)

Feb 11, 2016 | Jeep Cars & Trucks

1 Answer

Jeep wrangler electrical


igniton switch faulty.

Dec 16, 2013 | Cars & Trucks

1 Answer

I need a rebuilt carborator or a rebuilt engine for my 89 jeep wrangler loredo. where can i find a good mechanic in the san fernando valley, ca?


check your local jeep forums. try Project jk. com or just search jeep forums and your location on google. Most enthuist are shade tree machs. and from experince are more than happy to help wrench on another jeep. good luck and good wheelin

Aug 21, 2011 | 1989 Jeep Wrangler

1 Answer

Which fuse for my jeep wrangler 97 is for the ciggarette lighter?


Hi, the 1997 Wrangler has two fuses to check. Both in the Power Distribution Center (PDC) under the hood. Fuse 3 supplies the accessory circuits through the ignition key and energizes the coil of the accessory relay. If your radio works that fuse is OK. The other fuse, fuse 5 supplies the power to the accessory socket when the relay is energized. The relay is behind the glove box and mounted to a stack of multi-wire connectors.
Replace fuse 3

Jul 26, 2011 | 1997 Jeep Wrangler

2 Answers

89 jeep wrangler, starting problems


I would suspect the crank sensor, but it needs to be verified when it wont start.

Sep 27, 2009 | 1989 Jeep Wrangler

1 Answer

Location of Power Steering Reservoir


As far as I remember, the reservoir is part of the pump But...If it's not there it is easy to find...there are two hoses on the pump...one leads to the steering box mounted to the frame, the other goes to the reservoir, then to the steering box.

Aug 20, 2009 | 1989 Jeep Wrangler

1 Answer

89 Jeep Wrangler. Engine stalls only when I put into gear.


it might be getting to much fuel check the fuel screw

Jun 10, 2009 | 1989 Jeep Wrangler

2 Answers

1 Solution for 89 WRANGLER GETS HOT DIES/COOL THEN STARTS


One possible explanation for this is that the crankshaft position sensor is going bad.

Jun 09, 2009 | 1989 Jeep Wrangler

1 Answer

Fuse box


Under the left of the dash board close to the parking brake tucked up under.

Jan 02, 2009 | 1989 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...