2002 Subaru Outback Logo

Related Topics:

A
Anonymous Posted on Feb 23, 2013

Remove front bumper 2002 subaru outback - 2002 Subaru Outback

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Oct 09, 2008

SOURCE: what oil grade do i need in 2002 subaru outback?

Probably 5w40 synthetic

Ad

Anonymous

  • 133 Answers
  • Posted on Jan 09, 2009

SOURCE: fuse box location on 2002 Subaru

my books say there are two. one inside vehicle on drivers side below dash to the left of the steering wheel. the other is in the engine compartment on the drivers side by fender

Anonymous

  • 15935 Answers
  • Posted on May 23, 2009

SOURCE: needdrive belt diagram for Subaru outback 3.0

8c0dd6e.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Anonymous

  • 490 Answers
  • Posted on Sep 26, 2009

SOURCE: Outback 2002 subaru - Rear view mirror foggy; stopped working

there is nothing the shop did the that caused this they do that because of the heat inside the car sitting out in the sun

Anonymous

  • 377 Answers
  • Posted on Nov 11, 2009

SOURCE: Adjust the headlight beam on 2002 Subaru Outback

two screws on each headlight control the direction the headlights are aimed. One screw, usually at the top but sometimes below the headlight, adjusts the headlight up and down. The other screw, located to one side, controls the headlight from right to left. Turning the appropriate screw one direction or the other will change the direction the headlight points.
In order to aim your headlights you need to have a flat vertical surface you can aim your headlights at in front of a level surface on which to park the car. If your driveway is level your garage door is the perfect place to aim your headlights.
The tools you will need for this job are simple. Masking tape is used to mark where the headlights are to be aimed and a screwdriver is needed to adjust the headlights. A tape measure will be necessary to measure the distance of the vehicle to the surface you're using to check the aim and to measure the up and down distances from your marks

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
0helpful
1answer

2015 outback rear bumper removal

I assume you mean the bumper cover.

There's a set of two-piece plastic clips along the top of the bumper. Pry the center section out then the outer piece can be removed.
There's more clips along the bottom LH and RH sides.

And, there's an M6 bolt in the top of wheel arch end of the cover.
You should then be able to remove the cover.

The bolts to remove the bumper internal are now accessible.
0helpful
1answer

Where is the fuse box for 2002 subaru outback tail lights

On this website you find fuse box diagram and description for Subaru Outback (2001 - 2002)

SubaruOutback 2001 2002 fuse box diagram Auto Genius
1helpful
1answer

Starter on 2002 Subaru outback went out. How do I replace?

Wait for it to come back home, then disconnect the car battery, jack up the car, remove all the wiring to the starter, remove the two bolts holding it on. Reverse the procedure to install thr replacement.
1helpful
1answer

How do I remove rear bumper?

Hi i believe you remove the rear bumper by taking out the spare wheel and removing the rubber bungs exposing the bolts that are hidden beneath
0helpful
1answer

Location of thernostat on 2002 subaru outback 4-cyl

the thermostat housing on this vehicle bolts onto the bottom of the block, where the lower rad hose meets the engine. have a large drain pan handy, because the entire cooling system empties out when you remove the stat. good luck!
1helpful
2answers

Power steering pump replacement for Subaru Outback

REMOVAL

  1. Remove ground terminal from battery.
  2. Remove pulley belt cover bracket.



  1. Loosen lock bolt and slider bolt and remove power steering pump drive V-belt.
  2. Disconnect connector from power steering pump switch.



  1. Disconnect pipe C and suction hose from oil pump. CAUTION:
    • Do not allow fluid from the hose end to come into contact with pulley belt.
    • To prevent foreign matter from entering the hose and pipe, cover the open ends of them with a clean cloth.



  1. Remove bolts which install power steering pump bracket.



  1. Place oil pump bracket in a vise, remove two bolts from the front side of oil pump. CAUTION: Do not place oil pump bracket directly in the vise; use soft pads and hold oil pump lightly to protect the pump.



  1. Remove socket from oil pump.
  2. Remove bolt from the rear side of oil pump.
0helpful
1answer
Not finding what you are looking for?

550 views

Ask a Question

Usually answered in minutes!

Top Subaru Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Oliver Street

Level 2 Expert

73 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...