Question about 1996 GMC Sierra

Open Question

How to replace front wheel bearings on 1997 sierra 1500 4wd

Would like to view a how to video on replacing the front wheel bearings on my 97 gmc 1500 4x4

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 20 Answers

SOURCE: how do i replace front wheel bearings on the 4X4?

I suggest getting a hanes manual or a chilton.

Posted on Aug 17, 2009

Ad
  • 3 Answers

SOURCE: replace sway bar end links '97 GMC Sierra

if you put your vehicle information in at advanceautoparts.comyou can search sway bar and find parts that you need - there was someinfo missing on which sierra model you have as far as engine size andvin # match but I came to: http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/partlist_Sway-Bar-Link-Kit_78_R|GRPCHASAMS__sway%20bar___

Posted on Sep 17, 2009

  • 400 Answers

SOURCE: 97 gmc sierra won't go into 4x4. Electronic

Take the front axle actuator out of the axle. Plug it back in and have some one push the 4x4 button. The actuator should move, it's a liniar motor. If it doesn't then the actuator is bad or there is a wiring problem. If it does there is a problem in your front diff or some where else in the system.
I'd take a guess and say it's the front actuator.

Posted on Oct 11, 2009

  • 7353 Answers

SOURCE: Does a 99 GMC Sierra 4x4 need to have the front

NO.

Posted on May 14, 2010

  • 447 Answers

SOURCE: how do I change a front wheel bearing on a 2004

The hub, bearing, and ABS sensor are a single unit on this vehicle. You need to remove the wheel, brake rotor & caliper [don't disconnect the brake hose from the caliper, just support it out of the way] and then remove the large nut that holds the axle shaft in the hub assembly. Once you have all this loose or removed you'll find that the hub is held on with 3 fairly large capscrews that come in from the backside of the steering knuckle that the hub attaches too. Assembly is just the reverse of the process. Make sure you tighten all the bolts and nuts securely with a torque wrench [I don't have the torque spec's here] I apply threadlocker to all of these bolts as they are vital to safety. I only use OEM hubs on these as I've had the best luck with them and the ABS sensors inside of them.

Posted on Jun 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 97 gmc sierra 1500 4x4, it runs very nice the only thing is when i reach 40 mph, there is a slight vibration or shake. it seems to only happen between 40-45 mph, it runs perfect before 40mph and...


There are several things to consider, first I would check the tire balance. Then I would go to the front alignment. If you have trouble on one side or the other you may just have a bad tire.

Apr 01, 2011 | 1997 GMC Sierra

1 Answer

I have a 1994 GMC K1500 Sierra :5.7L 350CI V8 and I have a worn front wheel bearing and I took the hub off and saw that the inner bearing is in peices, Now I cant find where to find the bearing,, All I can...


the bearing hub is a pre-assembled unit it has to be pressed together and the bearings have to be preloaded that is why you can only buy the hub assy. and it a whole lot easier to replace then the old 4X4 ft. wheel bearings.HAVE FUN

Nov 16, 2010 | 1994 GMC Sierra

1 Answer

1997 GMC sierra 1500 5.7 liter. The antilock brakes have been activating a lot, especially when turning. I have had the wheel bearings replaced which contain the antilock sensors but the antilocks are...


clean the mounting surface of the abs sensors.rust builds up under the sensor and it sits too far away from the tone ring causing false abs modulation.

Nov 12, 2010 | 1997 GMC Sierra

1 Answer

Replace bad steering pump, *twice" seems to be steering hard to the left Checked front end and wheel bearings - no problem there


this problem is most likely the sterering gear box has a leaking fluid pressure assist valve

Jul 29, 2010 | 1997 GMC Sierra

1 Answer

Replacing aan intake gasket on a 97 gmc sierra


average around 500 cost at a shop

Apr 15, 2010 | 1997 GMC Sierra

1 Answer

Front differential quit


Does that have an electric clutch? I'm thinking it does ... I'm not really the guy to give you a comprehensive answer on this ... but check the power to the clutch.

Thanks for your interest in FixYa.com

Feb 26, 2010 | 1997 GMC Sierra

1 Answer

Replace sway bar end links '97 GMC Sierra


if you put your vehicle information in at advanceautoparts.comyou can search sway bar and find parts that you need - there was someinfo missing on which sierra model you have as far as engine size andvin # match but I came to: http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/partlist_Sway-Bar-Link-Kit_78_R|GRPCHASAMS__sway%20bar___

Sep 17, 2009 | 1997 GMC Sierra

Not finding what you are looking for?
1996 GMC Sierra Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

84966 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...