Need belt diagram or explanation of arrangement

The pistons are hitting the valves due to wrong alignment of timing gears and the timing belt. Align the timing gears and timing belt marks according to the following diagrams.


Good luck.

your Kia dealership can print you a diagram.

Many a times the problem occurs due to timing not adjusted,in many cases the timing belt also needs to be replaced while water pump replacing.
Or its also possible that water pump not replaced properly or timing got mistimed.
I suggest you to check few help links.-----------

For water pump replacement i suggest you to check the help link provided below.

click the link below :----

Water pump replacing procedure for all vehicles?

http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
---------

HOW TO REPLACE A WATER PUMP

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

------------------
How to route Water Pump Belt for 1992 Oldsmobile ?

http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

---------
How to replace Water Pump on Car ?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

---------
How to Remove Water Pump?

http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

-------
Where is Water Pump located ?

http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

-----------

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------

Car not starting or turning over indicates towards multiple possibilities. It can be issue with battery or weak battery. But if battery checks out ok, then it can be starter issue or faulty alternator or problem with low fuel pressure or no spark at spark plugs due to dirty spark plugs or faulty ignition coil or injectors getting cracked or dirty and needs to be cleaned.

To confirm the problem, the basic troubleshooting is required.

Click this link below and follow the troubleshooting:------

http://technoanswers.blogspot.in/2012/02/car-starting-issues.html

---------

This will help.

Thanks

Timing Belt Removal & Installation SOHC To Remove:

1. Disconnect battery negative cable.
2. Remove fresh air duct.
3. Drain engine coolant into an appropriate container and retighten radiator drain plug.
4. Remove upper radiator hose.
5. Remove fan clutch assembly bolts.
6. Remove 5 cooling fan shroud bolts.
7. Remove fan shroud and fan as an assembly.
8. Loosen alternator mounting bolts and remove drive belt from pulley.
9. Remove fan pulley.
10. Remove 4 cooling fan assembly bolts.
11. Remove cooling fan assembly.
12. Remove 4 bolts and upper timing belt cover.
13. Remove 2 lower bolts and lower timing belt cover.
14. Loosen adjusting bolt and remove A/C belt.
15. Remove alternator belt.
16. Loosen power steering pump lock bolt and mounting bolt.
17. Remove drive belt from crankshaft damper. Camshaft timing marks
    
    
18. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
19. Remove 5 bolts and remove damper.
20. Remove timing belt guide from timing belt pulley.
21. Loosen tensioner lock bolt.
22. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt. NOTE: Mark the direction of timing belt rotation on the belt if it is being reused.
    
23. Remove timing belt.

To Install:
Timing belt pulley timing marks

NOTE: Timing belt pulley timing mark and timing mark must be aligned.
Camshaft timing marks

NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
Timing belt installation

1. Install timing belt with minimal slack from timing belt pulley to water pump and from water pump to camshaft pulley.
2. Loosen tensioner lock bolt until tension is applied to timing belt. CAUTION
   Do not turn crankshaft counterclockwise.
   
3. Turn crankshaft pulley 2 full turns clockwise and ensure timing marks are properly aligned.
4. Tighten tensioner lock bolt to 33 ft lb (45 Nm).
5. Apply a force of 21 lb to timing belt midway between idler pulley and camshaft pulley.
   • Deflection should measure 0.43-0.51 inch (11-13 mm)
   NOTE: if timing belt deflection is incorrect remove timing belt and install NEW tensioner spring.
   
6. Install timing belt guide.
7. Install crankshaft damper pulley.
8. Install 5 crankshaft damper pulley bolts. Tighten bolts to 132 in lb (15 Nm).
9. Install power steering pump drive belt.
10. Adjust power steering pump drive belt tension and tighten lock bolt and mounting bolt.
11. Install alternator drive belt.
12. Install A/C drive belt.
13. Install lower timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
14. Install upper timing belt cover and bolts. Tighten bolts to 84 in lb (10 Nm).
15. Install cooling fan assembly and 4 bolts. Tighten bolts to 27 ft lb (37 Nm).
16. Install fan pulley.
17. Install fan clutch and shroud as an assembly. Tighten bolts to 74 in lb (8 Nm).
18. Tighten 4 cooling fan nuts to 16 ft lb (22 Nm).
19. Adjust alternator belt tension and tighten alternator mounting bolts.
20. Install upper radiator hose.
21. Install fresh air duct.
22. Connect battery negative cable.
23. Refill/bleed cooling system.

DOHC To Remove:

1. Disconnect battery negative cable.
2. Remove fresh air duct.
3. Remove 5 cooling fan shroud bolts and 4 thermo-modulated fan nuts.
4. Remove 4 thermo-modulated fan shroud fasteners.
5. Remove generator drive belt.
6. Remove fan pulley (located above crankshaft pulley).
7. Remove 4 bolts and splash shield (located under front of vehicle).
8. Remove A/C drive belt and power steering drive belt. Timing Belt Removal
   
   
9. Remove 5 bolts and upper timing belt cover.
10. Remove 2 bolts and lower timing belt cover.
11. Loosen tensioner lock bolt and pivot tensioner pulley outboard.
12. Retighten tensioner lock bolt. NOTE: Mark timing belt for rotation if it is being reused.
    
13. Remove timing belt.

To Install:
Crankshaft match marks

1. Align marks on timing belt pulley and pump body. Camshaft pulley alignment marks
   
   
2. Align marks on camshaft pulleys with alignment marks on seal plate.
3. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
4. Loosen tensioner lock bolt.
5. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
6. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
7. Apply a force of 22 lbs to timing belt between camshaft sprockets.
   • Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
   NOTE: Replace tensioner spring if timing belt deflection is excessive.
   Timing Belt Installation
   
   
8. Install lower timing belt cover.
9. Install upper timing belt cover.
10. Install power steering drive belt and adjust belt tension.
11. Install fan pulley.
12. Install generator drive belt and adjust belt tension.
13. Install A/C drive belt and adjust belt tension.
14. Install splash guard.
15. Install fan and fan shroud.
16. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
17. Install fan shroud mounting bolts.
18. Install fresh air duct.
19. Connect hose to resonance chamber.
20. Connect battery negative cable.

You didn't mention the alternator, power steering pump, or water pump. In fact, any pulley other than the crankshaft one can have a bad bearing or dry seal. Remove the belt and spin each pulley while listening for any rough noise or squeal. If it was the crankshaft, it might be time to check the oil. Start the engine with the belt off to see if it does squeal. Make sure the noise isn't coming from the radiator fan(s).

Check this diagram:



Fig. Timing belt routing-3.4L (VIN X) engine




Fig. Timing belt arrangement-3.4L (VIN X) engine



Fig. When installing the camshaft timing belt, work counterclockwise-3.4L (VIN X) engine

Good luck, and remember rated this help.

That is a valid question, but you should ask the shop that worked on it. Also do you know that the power steering pump will cure the problem? This remains to be seen....You can check one thing though...Look at the belt/pulley arrangement from the side. any pulley that is not exactly in line with all others, and any wobbling pulley is suspect. Serpentine belts are far less forgiving of these items than were "v" belts.
Good luck

1. Remove the alternator & power steering pump drive belts.
2. Remove four (4) 10mm bolts holding the water pump pullys & remove the pullys.
3. Drain the Radiator (save coolant if intend to reuse).
4. Loosen & remove AC compressor belt.
5. Remove crankshaft pully (22mm bolt).
6. Remove lower timing belt cover (10 mm bolts) to access water pump bolts.
7. Remove the water pump (12mm bolts)
(1) Remove the 2 bolts, then remove the alternator brace (A). (2) Remove the water pump (B) and gasket.
8. Clean mating surface on engine & install new gasket & pump - reassemble. Refill w/50-50 coolant.

Since your friend just replaced the timing belt, there wouldn't be a need to replace the oil pump O-ring and crankshaft seal unless they were leaking.

No, you cannot get to the oil pump unless the crankshaft, lower timing belt cover and belt are removed.

I have the same exact car with the same engine and just replaced the oil pump O-ring and crankshaft seal. I'm a good mechanic, but this is a tedious and time consuming job, but It can be done if you have good mechanic skills.


VERY IMPORTANT.
There is a big chance that the car's engine timing will be off, have someone who is knowledgeable to set the engine timing. If you don't and try to start the car, serious engine damage will probably occur.

ALSO IMPORTANT.
When you get the oil pump off removed all the old O-ring the new oil ring will not stay in place, I used petroleum jelly to keep the ring in place, it's perfectly safe and won't affect the operation of the oil pump.

If your not sure you can do the repair yourself, take it to a mechanic.

BELT, REPLACE

1. Release belt tension and remove belt from power steering and alternator pulleys. Twist belt to get between tensioner and front cover and between power steering pulley and engine mount bracket.
2. Raise and support vehicle.
3. Turn wheel to the extreme right and remove right side splash shield.
4. Remove belt from crankshaft and A/C compressor pulleys. Twist belt to get between idler pulley and engine mount bracket.
5. Lower vehicle.
6. Twisting new belt to get past the front cover, install belt around power steering pump pulley, Fig. 15. Allow belt to hang free.
7. Twist belt to get between tensioner and front cover, wrap belt around alternator.
8. Remove belt from power steering pulley and set aside.
9. Raise and support vehicle, then twist belt to get between tensioner and front cover, wrap belt around crankshaft and A/C compressor pulleys.
10. Install right side splash shield and lower vehicle.
11. Position belt around power steering pulley and release tensioner.