89 Ford Ranger Carrier bearing

Here is the cylinder hear torque search query. Change for each part and press Enter.

https://www.google.com/search?q=2005+ford+ranger+2.5+cylinder+head+bolt+torque+settings

https://www.google.com/search?q=2005+ford+ranger+2.5+main+bearing+bolt+torque+settings

https://www.google.com/search?q=2005+ford+ranger+2.5+con+rod+bearing+bolt+torque+settings

or the manual

https://barringtondieselclub.co.za/ford/ford-ranger-2.5-he-4-cyl-engine.html

..

36mm is the consensus of opinion, but in reality, it is the socket that 'FITS'! Most socket sets come in metric and imperial, you use that one that is the best fit.

Axle nut socket ' Ford Explorer - Ford Ranger Forums ...

www.explorerforum.com > forums > threads > axle-nut...

Jan 22, 2008 - Anyone know what size socket for the axle nut? ... Mercury Mountaineer, Mazda Navajo, Ford Ranger, Mazda Pickups, and the ... 34mm front axle 36mm rear axle ... One more question, I know the bearing has to be pressed onto the hub but does it then ... Year, Model & Trim Level: 2004 Explorer Limited V8. Axle Nut Size? ' Ford Explorer - Ford Ranger Forums - Serious ...
Aug. 9, 2016
Front and Rear Axle Nut sizes? ' Ford Explorer - Ford Ranger ...
Feb. 28, 2016
What size socket is the wheel bearing nut? ' Ford Explorer ...
May 22, 2003
Spindle axle nut size ' Ford Explorer - Ford Ranger Forums ...
Aug. 19, 2009
More results from www.explorerforum.com

..

Ford Ranger 2.3 rebuild part 3 "xTUPID BOLTS" - YouTube

? 2:55
www.youtube.com/watch?v=ZJ1jFK4weUE
Mar 28, 2011 - Uploaded by DirTyOhGee
89 Ford Ranger 2.3 Custom/Limited. Moving right along here, ...How to change the timing belt on a Ford 2.3L engine. - Duration: 29:59. by ...

You should be able to rent a spline alignment tool from the parts house where you got transmission. I'm assuming you have a manual transmission so the clutch pad doesn't want to cooperate? I think even with an automatic it's much the same.

2001 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl

1. Drain the cooling system.
2. Disconnect the radiator hose and the electrical connector.
3. Disconnect the radiator lower hose.
4. Remove the bolts and the thermostat housing.
5. To install, reverse the removal procedure. Tighten the housing bolts to 89 inch lbs. (10 Nm).

Hope helps (remember to rate and comment this).

Have the fuel pressure checked,and replace the fuel filter first,it is most likely one of the two causing the problem,if this was helpful,please rate,thank you.

Could be low oil level, a bad sending unit, or actually low oil pressure due to a worn oil pump or worn bearings.

Measure the distance from bolt to bolt, and to the center. If they match then, they match, if not you will have to check the numbers with fords tolerances to avoid an axle wrap. But it should fit, maybe just a little stiffer of a suspension from the 4x4.
Calvin the Mobile Mechanic.

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

To replace the centre bearing you first remove driveshaft from vehicle.
Pull the shaft apart at the middle universal joint.
On the back of the section that has the centre bearing you will see a nut that holds the uni ears onto the shaft.
Undo the nut and remove the ears. Then press the centre bearing off the shaft and reassemble with new one.
Hope this is more helpful.