Driver window controls do not work and some still do

You say the driver window works? wouldn't be a main fuse or fusible link then -driver door locks and window wouldn't work either. Each door has a module inside (computer) . The driver door has a circuit breaker power feed an a fuse DDM fuse 10amp located in rear junction block circuit breaker is located in under hood maxi fuse block. The circuit breaker also feeds battery voltage to the other door modules too. PDM - passenger door module fuse 10amp located in the instrument panel fuse box and the RDM - rear door module RDM fuse 10amp located in the rear fuse box - under the back seat.

Each power window is connected to a permanent magnet motor. The motor raises or lowers the glass when the door module applies voltage to the motor. The direction the motor turns depends on the polarity of the supply voltage provided by the associated door module. The 2 front doors have their own separate modules. The rear seat contains a single module, which controls both of the rear power windows.
A serial digital communications link, called the simple bus interface, is used for communications between door modules and the driver's door power window switches. The use of serial digital communications allows the use of a single wire to convey switching information between the power door lock switch and the driver's door module (DDM). The serial communication is also used in order to transmit switching information from the DDM to the other 2 door modules.
The door modules apply battery voltage of the correct polarity to the respective window motor when any local, or power door lock switch, UP switch is operated, driving the window up. Battery voltage is applied to the respective window motor in the opposite polarity when any local, or power window switch, DOWN switch is operated, driving the window down.

Driver Door Module (DDM)
The driver's door module (DDM) directly controls the driver's door window motor and the express down window feature. The DDM sends window UP/DOWN messages received from the power door lock switch to the passenger door module (PDM) and to the rear door module (RDM) over the simple bus interface (SBI) line. The DDM also contains a class 2 data link which communicates with the other vehicle system modules. The left front power door locks and the outside power mirror are also controlled through the DDM.
Passenger Door Module (PDM)
The passenger door module (PDM) controls the passenger's door window motor. The PDM controls the passenger's door window directly from the right front power window switch or from instructions over the simple bus interface (SBI). The right front power door locks and the outside power mirror are also controlled through this module.
Rear Door Module (RDM)
The rear door module (RDM) controls both of the rear door window motors. The RDM controls the rear windows directly from the rear door window switches or from instructions over the simple bus interface (SBI).

Some people pour warm water on the door top to thaw it out.
Hope this helps.

Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Window regulator is bad in the drivers door . Do you know what a regulator is ? The Trainer 24 Power Window Troubleshooting Do you know anything about automotive electrical testing ? How to read an use a wiring diagram ? Do you know there are two side to a electrical circuit ? B+ voltage an a ground side . Plus there is electronic control modules and class 2 serial data network involved . When you push the switch for a window othen then drivers window on the drivers door . a class 2 message is sent to the other doors modules . The correct module will then open it's window .
http://www.bbbind.com/free_tsb.html Check out free wiring diagram here .Enter vehicle info . year , make , model and engine size. Under system click on body & accessories , subsystem click power windows . Click search button , then click each link one at a time .

Look at the body control module.

mine does the same.. disconnect the battery.. then reconnect.... works everyime! ive had to do it 3 times in 2 yers

Hi,
Hi!!

Here is a little information on how window regulator works. Also step by step instruccions on how to remove and install the window glass.

Door Glass & Regulator Power Windows
Diagnosis & Testing
When the rear window lockout feature is enabled, the circuit is open and no voltage is supplied to the rear window switches. When the feature is not enabled, the circuit is connected to battery positive voltage. If this circuit is shorted to ground when the lockout feature is not enabled, the PWR WDO circuit breaker may cycle continuously OFF/ON until, either the lockout switch is pressed to open the circuit, or the circuit breaker is permanently damaged. All windows may be partially or totally inoperative while the fault is present.
Inspect for aftermarket devices which could affect the operation of the system. Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. Faulty electrical connections or wiring may be the cause of intermittent conditions.
Removal & Installation
Window Motor & Regulator

1. Position window approximately half way down in the door.
2. Remove the interior trim panel.
3. Remove the water deflector.
4. Tape the window to door frame to prevent it from moving.
5. Remove the three front door window regulator motor screws.
6. Disconnect the electrical connector from the window regulator motor.
7. Remove front side door window regulator motor.
8. To install, reverse removal procedure.

Window Switch
Front

1. Remove the front door pull cup screws and pull cup from the front door trim panel.
2. Disconnect the electrical connectors from the front door power window control switch.
3. Remove the front door window control switch using a small, flat-bladed tool at the side of the switch.
4. To install, reverse removal procedure.

Rear

1. Remove the rear door pull cup from the rear door trim panel.
2. Disconnect the electrical connectors from the power window control switch.
3. Remove the rear door window control switch from the pull cup using a small, flat-bladed tool at the side of the power window control switch to release the power window control switch retainer.
4. Remove the power window control switch from the rear door pull cup.
5. To install, reverse removal procedure.

It may be that it is not on the track properly or your power window motor is old and tierd and can take the window down but it doesn't have the juice in it any more to bring it back up. replace the motor and it will work. This problem happened to me in my '76 ford ltd and a new motor fixed it.

Does the rear window work from the passenger switch?

I had the same problem with now power to windows, mirrors and seat. The common soulution is the orange and or black wire in the boot have broken between the door and post.