Question about 2005 Chrysler Pacifica

1 Answer

2008 Chrysler Pacifica Interior Lighting Malfunction

The interior lights does not operate when you manual start one individually. When the door opens all lights illuminates but when you're driving and want to turn on a particular light, neither works. Does or has anyone else seen this problem and know whats causing this malfunction?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 15,575 Answers

Does or has anyone else seen this problem and know whats causing this malfunction? /////
Could be a number of thing's , testing the electrical circuit's with a DMM - digital multi-meter is the way to find the problem . What fixes someone else's vehicle very rearly fixes other . Unless of course it is a problem with the TIPM - totally integrated power module . Electronic control module . Chrysler has a recall on these . Your best bet mite be to take it by the dealer an have it checked out ,

Posted on Mar 05, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 46 Answers

SOURCE: how do i turn off my malfunction indicator light?

If it is an error produced by the engine control system, you should be able to clear it using an OBD II reader. OBD=on board diagnostics. You have to find the plug for the unit, but just plug it in and the machine will read it. I usually borrow one from the local car parts store--give an ID and they will let you temporarily borrow it. Make sure you read the error code as well. There may be some interesting info about what produced the error message. Good luck.

Posted on Apr 09, 2009

motor1258
  • 6674 Answers

SOURCE: Interior light or cigarette lighter not working,

That's where a $5.00, 12 volt test light comes in handy. All you have to do then is touch tip on ends of fuses to see if they are good or not. No pulling fuses and no head scratching wondering which one it might be. If you have power on one side, but not the other, you found the blown fuse. It certainly is not uncommon to find the bad fuse, labeled wrong, or added in with something else that makes no sense at all.

Posted on Apr 13, 2009

SOURCE: egr valve malfunction/failure what are symptoms? 3.5 v6 2004 paci

Your best bet would be to check your catilytic converter, thats the thing in your exhaust system under the car that looks like a muffer, it could be clogged, triggering the Exhaust Gas Recirculation (EGR) fault code. However, I don't trust those scanners from these autoPARTS stores have a proffessional diagnosis done you will save money and headaches later. You probably have more than one trouble code. As for the fuel pump you will know when it goes bad, the vehicle will stop running period, so, don't change that.

Madchanic.

Posted on Jul 28, 2009

  • 819 Answers

SOURCE: Camshaft sensor malfunction...code 0340.

i believe it is on the drivers side end of the head, accesable from the top.

Posted on Nov 13, 2009

wiringlunati
  • 576 Answers

SOURCE: instrument cluster bulb is out. how do i replace

It may not be a bulb, as the instrument cluster usually has a number of bulbs and they probably didn't all blow at once. Pulling instrument clusters can be touchy and may not be for the average "shadetree mechanic" however, typically there are a few screws above the cluster going into the dash pad and a few hidden behind the trim panels below the cluster.

Posted on Dec 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which fuse is interior light fuse for 2006 ford f150


free diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine . Under system click on lighting , then under subsystem click on interior lighting . Click the sear search button then the blue link. I see one fuse in the CJB F24 - 15 amp . Also i see battery saver relay . The instrument cluster energizes the battery saver relay .

Principles of Operation
Vehicles equipped with remote keyless entry (RKE) have an illuminated entry feature, which enables the instrument cluster to illuminate the interior lamps (and if equipped, the puddle lamps in the exterior mirrors) when an unlock signal is received from the vehicle security module through the UBP network, or when any of the doors are opened. The instrument cluster controls the interior lamps illuminated entry feature by activating the battery saver relay. When active, the illuminated entry feature will be canceled when any of the following conditions are met:
  • 25 seconds have elapsed since the illuminated entry feature was activated and the interior lamp control is not activated (door ajar or dimmer control switch ON).
  • On vehicles equipped with RKE, the instrument cluster received a request from the vehicle security module (remote transmitter lock button pressed) and the interior lamp control is not activated.
  • The ignition is in the RUN or START position and the interior lamp control is not activated.
For vehicles equipped with RKE, the instrument cluster illuminates the interior lamps when any door is open. The interior lamps shut off when the doors are closed and the illuminated entry feature is not active or when the vehicle speed is greater than 15 km/h (6 mph). The interior lamps are not reactivated until the vehicle speed is less than 15 km/h (6 mph) and a new door open signal is received.
For vehicles without RKE, the instrument cluster illuminates the interior lamps and puddle lamps (if equipped) when any door is open. The instrument cluster will turn the interior lamps and puddle lamps (if equipped) OFF when the doors are closed.
Power to the on-demand lamps, illuminated vanity mirrors and map lamps are controlled by the battery saver relay.

Inspection and Verification
  1. Verify the customer concern.
  1. Visually inspect the following for obvious signs of electrical damage:


Visual Inspection Chart Electrical
  • Bulbs
  • Central junction box (CJB) fuse 24 (15A)
  • Circuitry
  • Vehicle security module (if equipped with RKE)
  • Instrument cluster
  • Door ajar switches

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the cause is not visually evident, connect the diagnostic tool to the data link connector (DLC) and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • CAN, ISO or UBP circuits fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • No response/not equipped for instrument cluster, refer to Section 413-01 .
    • No response/not equipped for vehicle security module, refer to Section 419-10 .
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics for the instrument cluster.
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics for the vehicle security module.
  1. If the DTCs retrieved are related to the concern, go to the Instrument Cluster Diagnostic Trouble Code (DTC) Index or the Vehicle Security Module Diagnostic Trouble Code (DTC) Index.
  1. If no DTCs related to the concern are retrieved, GO to Symptom Chart .

Jun 20, 2018 | Ford F-150 Cars & Trucks

1 Answer

I'm needing a fuse diagram for my 1997 Ford Econoline club wagon. The interior lights aren't turning on when open the door. Lights use to come on when I first got the van, but now they don't.


When you open any door ? Driver ,passanger etc... You would need to look at a wiring diagram to see what all is involved in making the light's come on . Has an electronic illuminated entry module that controls the light's . Use's RH & LH door handle switches as inputs to the module . Has two fuse's in the instrument panel fuse box #4 a 15amp fuse & # 24 a 5 amp fuse . Probably not a fuse problem . module maybe . Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. Year , make , model an engine size. Under system click on lighting , then under subsystem click on illuminated entry . Click the search button ,then the blue link .
The system is activated by raising the door handle (22404).
This action momentarily closes a switch mounted on the front door latch, which completes the ground circuit of the electronic module and switches the system on. The vehicle interior lamps turn on, remain on for approximately 25 seconds, then automatically turn off. During this 25 second period, the system can be manually deactivated by turning the ignition switch (11572) to either RUN or ACC position.
The system will be activated every time the door handles are operated. Opening the interior lamp switch from the inside of the vehicle will not activate the system.
If the door handle is held up indefinitely so that the interior lamp switch is continuously closed, the system will operate as normal and turn off after 25 seconds. At the completion of this cycle, if the door handle is still in the raised position, the system will remain off, and it will be impossible to activate the system from the other door handle until the raised door handle is returned to its normal position. This function is built into the logic circuitry of the system to prevent battery discharge, should the door handle be intentionally propped up or become jammed in any way.

Apr 21, 2018 | Ford Cars & Trucks

1 Answer

I have a 2007 Buick Lucerne and the front reading lamps won't turn off.


Overhead Console Lamp and Roof Rail Courtesy/Reading Lamps
The courtesy/reading lamp is a duel purpose lamp that can be illuminated two different ways. First, the lamp can be turned ON during courtesy lamp operation as described above. Second, the lamps can be turned ON individually for reading lamp operation by the lamp switch. The BCM supplies battery voltage from the INT LAMPS fuse through the inadvertent power courtesy lamps circuit to the courtesy/reading lamps for reading lamp operation only. Ground for the courtesy lamp module or the roof/rail reading lamps is provided at G402

Courtesy Lamps
When either one of the front doors is opened, ground is applied through the door latch door open switch and the door open switch signal circuit to the door module indicting the door open position. In response to this signal, the door module sends a GMLAN serial data message to the BCM of the door open position. Or, when either one of the rear doors is opened, ground is applied through the door latch door open switch and the rear door open switch signal circuit to the BCM is indicating the rear door open position. Once a door open message or signal received, the BCM will then apply battery voltage from the CTSY/RF TRN fuse through the courtesy lamp supply voltage circuits illuminating the lamps listed below:
• Overhead console lamp
• Roof rail courtesy lamps
• Footwell courtesy lamps The BCM receives battery voltage from the INT LAMPS fuse in order to supply power to the inadvertent courtesy lamps. Inadvertent power courtesy lamp feature provides a similar function for the interior lamps as a retained accessory power feature. The BCM will energize the courtesy lamps supply voltage circuit when the BCM is in the active state (awake). When the inadvertent power courtesy lamps supply voltage circuit is energized, it supplies voltage to all the interior lights listed below. The BCM will continue to supply voltage to the interior lamps after the ignition is turned OFF so that the interior lamps may be operated.
• Overhead Console Reading Lamps
• Roof Rail Reading Lamps
• Vanity Mirror Lamps
• I/P Compartment Lamp
• Rear Compartment Courtesy Lamp
In the event that any of these lamps were to remain illuminated for a period of more than 20 minutes with the ignition switch in the OFF position and no BCM input activity, the BCM will deactivate the inadvertent power supply voltage circuit to prevent a total battery discharge condition. The BCM receives battery voltage from the CTSY/RF TRN fuse in order to supply power to the courtesy lamps. The BCM applies this voltage to the courtesy lamps through the courtesy lamp supply voltage circuits. When any door is opened, the door open switch contacts close and the BCM receives a door-open signal. If the BCM receives a door lock or unlock signal, the BCM will activate the courtesy lamp supply voltage circuit, providing battery voltage to the dome lamps and the left and right footwell courtesy lamps. The courtesy lamps can be manually activated by placing the interior lamp switch in the DOME position. For more detailed information concerning courtesy lamp operation refer to Interior Lighting Systems Description and Operation.

Jan 16, 2017 | Buick Cars & Trucks

1 Answer

Just got my 2003 explorer sport trac dome light dont come on when you open the doors but they come on when you push the button to turn them on how do I get them to come on when I open the doors?????


The instrument cluster illuminates the interior lamps when an unlock signal is received from the vehicle security module. The illuminated entry feature will be canceled when any of the following conditions are met:
  • 25 seconds have elapsed since the illuminated entry feature was activated and the interior lamp control is not activated (door ajar or courtesy lamp switch on).
  • The instrument cluster receives a request from the vehicle security module (remote transmitter lock button pressed) and the interior lamp control is not activated.
  • The ignition is in the RUN or START position and the interior lamp control is not activated.
The instrument cluster illuminates the courtesy lamps when any door is open or ajar. The courtesy lamps shuts off when the doors are closed and the illuminated entry feature is not active or when the vehicle speed is greater than 5 mph (8 km/h). The interior lamps are not reactivated until the vehicle speed is less than 3 mph (5 km/h) and a new door open warning lamp signal is received.
The instrument cluster controls the courtesy lamps illuminated entry function by activating the battery saver relay.
The panel dimmer switch is integrated into the headlamp switch and controls the interior lamps by activating the instrument cluster through circuit 1034 (BK/WH).
The vehicle security module sends a signal to the instrument cluster on the UBP network circuit to indicate a request to turn the illuminated entry feature on or off.
The on-demand lamps, glove compartment assembly, homelink module, puddle lamps and illuminated vanity mirrors are controlled by the battery saver relay. The battery saver relay becomes active (relay coil is energized) when the instrument is in the awake mode, or in the sleep mode (relay coil is de-energized).

Nov 28, 2016 | 2003 Ford Explorer Sport Trac

1 Answer

My 2004 Pontiac grand am se1 acts like door is open and interior light stays on also does t lock on its own when in gear and lights don't blink and horn not honk when locking with key bob


Door ajar switch problem more then likely or wiring issue . The BCM - body control module won't turn off interior light , let door lock because it think's the door is open . The door ajar switch is a input to the BCM .

The first thing would be to have it checked for DTC'S - diagnostic trouble codes . Also check with an enhanced scan tool to see if the BCM shows ajar switch data (open or closed ? Do you know about body electronics ?
Body Control Module
The various BCM input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The Body Control Module functions include the following:
?€¢
A/C compressor request. Refer to Air Temperature Description and Operation


?€¢
Remote Function Control. Refer to Keyless Entry System Description and Operation


?€¢
A/C cooling Fan. Refer to Air Delivery Description and Operation


?€¢
Audio Delay Power. Refer to Radio/Audio System Description and Operation


?€¢
Exterior and interior lighting control. Refer to Exterior Lighting Systems Description and Operation


-
Daytime running lights (DRL)


-
Automatic lighting control


-
Fog lamps


?€¢
Interior lighting. Refer to Interior Lighting Systems Description and Operation


?€¢
Battery rundown protection (Inadvertent Power). Refer to Interior Lighting Systems Description and Operation


?€¢
Chimes. Refer to Audible Warnings Description and Operation


-
Key-In-Ignition


-
Head Lamps On


-
Seat Belt Not Fastened


-
Turn Signal On


-
Park Brake Warning


-
Door Ajar Warning


-
Check gages


?€¢
Gage control. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.


?€¢
Instrument cluster indicator control. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.


?€¢
Theft deterrent. Refer to Theft Systems Description and Operation .


?€¢
Engine coolant level sensing. Refer to Cooling System Description and Operation .


?€¢
Washer solvent level sensing. Refer to Wiper/Washer System Description and Operation in Wipers/Washer Systems.


?€¢
Key-in-ignition sensing. Refer to Audible Warnings Description and Operation in Instrument Panel, Gages, and Console.


?€¢
Seat belt use sensing. Refer to Seat Belt System Description and Operation .


?€¢
Brake fluid level sensing.


?€¢
Parking brake state sensing.


?€¢
Rear compartment interface. Refer to Power Door Locks Description and Operation


?€¢
Horn interface.


?€¢
Door lock interface. Refer to Power Door Locks Description and Operation


?€¢
Bulb Check. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.

Oct 24, 2016 | 2004 Pontiac Grand Am

1 Answer

2002 ford expedition interior lights are not on what fuse is it?


Courtesy Lamps - central junction box. fuse # F1.21 that goes to interior lamp relay in the instrument cluster and F.24 this fuse powers battery saver relay .
Interior Lighting The interior light system consists of the following:
  • front map lamp assembly
  • front door courtesy lamp
  • generic electronic module (GEM)
  • glove box lamp assembly
  • central security module
  • interior lamp switch
  • interior lamp relay
  • illuminated vanity mirrors (Navigator only)
  • reading lamp assembly
  • rear courtesy lamp
  • running board lamp
  • underhood lamp assembly
  • The generic electronic module (GEM) illuminates the interior lamps when an unlock signal is received from the remote anti-theft personality central security module. The illuminated entry feature will be canceled when any of the following conditions are met:
    • 25 seconds have elapsed since the illuminated entry feature was activated and the interior lamp control is not activated (door ajar or courtesy lamp switch on).
    • The GEM receives a request from the central security module (remote transmitter lock button pressed) and the interior lamp control is not activated.
    • The ignition is in the RUN or START position and the interior lamp control is not activated.
    The GEM will illuminate the interior lamps when any door is open or ajar. The interior lamps are; the dome lamp, the rear cargo lamp, the door courtesy lamp and the side rail lamps. The courtesy lamps will shut off when the doors are closed and the illuminated entry feature is not active or when the vehicle speed is greater than 5 mph (8 km/h). The interior lamps will not be reactivated until the vehicle speed is less than 3 mph (5 km/h) and a new door open warning lamp switch is received.
    The GEM controls the interior lamps illuminated entry function by activating the interior lamp relay.
  • You have an electronic control module and relays involved in the operation of these lights also !

  • What

    Jan 08, 2015 | 2002 Ford Expedition

    3 Answers

    INTERIOR LIGHTS WILL NOT COME ON WHEN I OPEN THE DOOR, TURN OFF THE ENGINE, ETC


    Is bulb/fuse ok?
    If so could be the door swich. Have you tried the opening the other door?

    Nov 19, 2014 | 2008 Toyota Highlander

    2 Answers

    INTERIOR light will not turn off.How to turn off ???


    The interior light has a switch that allows it to be turned on manually. The light will stay on until switched off to return it to automatic operation.

    Nov 13, 2014 | 2005 Ford Mustang

    Not finding what you are looking for?
    2005 Chrysler Pacifica Logo

    Related Topics:

    247 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    Marvin
    Marvin

    Level 3 Expert

    85160 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...