Cars & Trucks Logo

Related Topics:

Posted on Feb 06, 2013

My Atak A4 remote was programmed to my T.V. and now it's not, I can't find my manuel to reprogram the T.V. again

I don't no what the T.V. brand is at the moment, but it is an off brand that the code was not listed and I had to do a code scan to program the remote.

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 19 Answers
  • Posted on Feb 06, 2013
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Feb 06, 2013
Answers
19
Questions
1
Helped
3796
Points
54

You will have to re do the code scan again. if remote loses power it will lose the saved settings and go back to default

5 Related Answers

Anonymous

  • 4 Answers
  • Posted on Apr 09, 2009

SOURCE: lost jeep 2000 grand cherokee key and remote

go to the car dealer and tell them that you need to get a new key and remote for your car

Ad
raygin

Raygin

  • 322 Answers
  • Posted on Apr 09, 2009

SOURCE: programing

solution already posted elsewhere in forum - good luck

Anonymous

  • 3533 Answers
  • Posted on Apr 13, 2009

SOURCE: I can't seem to get my remote to program. I have

if you have try everything and it does not work you may have to take the car along with the remotes to have them program to you car at your local dealership because you have to have a computer to do it if your owner manual does not tell you how too.

Anonymous

  • 4 Answers
  • Posted on Apr 26, 2009

SOURCE: 97 AUDI A4 RADIO STATIONS

tune in the station you want and press and hold the number you want it to be saved to

Molson02536

Harvey N Tawatao

  • 3854 Answers
  • Posted on Oct 29, 2009

SOURCE: 2003 Montana Remote & Key Programming Help ..

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I need the keyless entry programming code for my 01 Audi A4 Quattro 1.8T Note: Driverside lock doesn't work with regular key, and is the only lock on the entire car.

That isn't how it works, you must have the dealer reprogram the whole system to correct this if the loss of program is the cause. You can't do it at home it requires a special tool to go int the control modules programing option.
0helpful
1answer

Do i need to reprogram my car if i replaced the battery to remote

No you don't the program is inside your main ECU not the remote. Cheers
0helpful
1answer

The remote start quit working on my 2008 mercury mountaineer, what do I need to do to fix it.

These remotes most likely don't have to be reprogramed. Just take the battery out and replace it. It should work after that.
0helpful
1answer

Yaris hatchback wont open

The remote may have a bad battery or the system has lost programming, refer to the owner's manual to change the battery in the remote and if that doesn't cure it the dealer must use a special tool to reprogram the system to the remote frequency. This solution is based on the fact that both the remotes don't work, the remote can be bad, this is esp true if it has been dropped.
0helpful
1answer

Flat battery in keyless remote

copy or reprogram keys.

I don't know what is your car model and year, so I just can recommend you the Toyota Camry key 3 button 315MHZ.
I don't if it can do for you.
5helpful
2answers

I have a 2007 Toyota RAV 4 I can't get the remote to work after changing the battery does it have to be reset if so what has to be done. I can lock and unlock the doors manualy but not with the remote...

1. get in the car
2. shut the door
3. place the key in the ignition
4. lock the doors, manually
5. turn the ignition to on then off...do this seven times
6. unlock the doors and try your remote
3helpful
2answers

Programming the keyless remote

if you have the original remote, you can do it yourself. My remote was working without a problem until the other day when all of a sudden it didn't work out of nowhere. I thought it was the battery (might have been and needed to be reprogrammed after replacing it) so I changed it. Still didn't work. So I did a search and found the following instructions: Click Here

The answer is remarkably simple:
1. Get in the car and close the door.
2. Turn the key to the ACC position
3. Push the unlock button on the remote until the blinkers flash once.
4. Get out of the car and test the remote. It should be working fine. ( I actually was able to test it while in the car)

P.S. I would change the battery first.
0helpful
1answer

Can your take a remote key from one a4 and reprogram it to work another one? If so how please?

Cant see why not, as long as you have the original key as well for the other car. If you search the net for Audi A4 key programming there are sites that tell you how for differant models.

Good luck.
2helpful
2answers

2000 A4 keless remote not working

You will have to take your remote in and have them reprogram the codes in it for you. If a remote battery has been dead for more than 5 mins on this then it will lose its memory, so it will then need the codes reprogramed
37helpful
4answers

Program a remote key for 03 A6

I have an A4 and did this to re-program my key:

1. used the key to start the car...then turned it off
2. put the key in the driver door (door closed)
3. pressed the lock button on the key fob once
4. turned the key to lock the door.

This is basically the steps in the owners manual, but the car must be started with the key first, and the key must be in the door lock before pressing the lock button.
Not finding what you are looking for?

248 views

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...