Bleeding the slave cylinder

Try bleed

1. Check the fluid level in the master cylinder. ...
2. Locate the bleed screw on the slave cylinder. ...
3. Attach the hose to the bleed screw. ...
4. Open the bleed screw on the slave cylinder. ...
5. Have a friend press the clutch pedal in and hold it. ...
6. Close the bleed screw. ...
7. Have your friend release the clutch pedal.

Bleeding Clutch by Blocking the Slave Cylinder

Bleed master first and then slave get tube on bleed nipple and keep pumping into bottle keeping tube in fluid in bottle so it will not draw air on return stroke some cars can be quite hard too bleed

Ford has special bleeding and blocking instructions for clutch slave. Check manual for proper bleeding requirements. May consider presurre bleeding of master cylinder or use master cyclinder bleeding tubes that fill the resevoir as you bleed the and remove all air in system.

the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

it could be either the master cylinder or the slave cylinder,it could also be the clutch pressure plate check the master & slave cylinders first because if it's the pressure plate the gear box will have to be removed to replace the pressure plate, even if you are uncertain it is most likely cheaper to replace the master & slave cylinders than it would be to replace the pressure plate.....hope this helps......cheers.

FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Probably not. Bleeding clutch slave cylinders is tricky because you cant "pump it up". The master cylinder has no static valve so the best way to bleed the slave cyl. is to use gravity. Fill the master cylinder reservoir and open the bleed valve on the slave cyl. Allow fluid to drip into an open can until there's no trace of air. Close bleed valve and try clutch. If still no pedal, repeat the process. This is quite an acceptable procedure.

Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.