Car will not start Have fuel to rail

Silverado 1500 or 2500 or 3500 or HD? no pickup told
not told the job you are doing>??
remove them all ,or scope them or just what, no job told
no end goal or task told. sorry can guess it.

like most V6/8 now , it is a sandwich.
the service manual covers all,l buy it rent it.?
toss dice and land on 1500
the rail on this engine, fuel rail like all , intake manifold injectors used;. all injector held down by both rails. left and right
now the steps to off them if is the job,
pull the isolator seen photo 1, far below.
1: pull left rail and right rail
Remove and discard the fuel injector retainer clips by installing EN-51097 injector retaining clip installer and spreading both sides of the clip evenly.
Always use NEW fuel injector collars supplied with injector when installing the new injector. If reinstalling the injector, it is not necessary to remove the collars unless the collars are being replaced.
Replace the injector seals as needed. Refer to Fuel Rail and Injectors Cleaning and Inspection.
Note
Inspect the injectors to be sure that they are clean and free of debris prior to installation. Do NOT lubricate the injector seals. Rebuild the fuel injectors whenever the injector has been removed from the fuel injector rail.


now I will past the other page rails off per the manual read to you.
just bank 1, i am to lazy to post both
step 1 rail off bank1.
Note
Inspect the injectors to be sure that they are clean and free of debris prior to installation. Do NOT lubricate the injector seals. Rebuild the fuel injectors whenever the injector has been removed from the fuel injector rail.

1. Remove the fuel pump insulator. Fuel Pump Insulator Replacement
2. Remove the fuel injector intermediate pipe position?1. Fuel Feed Intermediate Pipe Replacement - Position 1
3. Clean the cylinder head pocket around the injectors of any dirt or buildup.
4. Disconnect the electrical wiring harness connectors from the fuel rail.
5. the fuel rail fasteners are retained in the fuel rail by keepers and may be difficult to remove.Remove the fuel rail fasteners?(1) securing the injector rail?(2).
   Install two sets of EN-49248 remover?(3).
6. Install one remover in each of the fuel rail fastener bores.
7. Remove by turning each section of the EN-49248 remover an even amount to pull the fuel rail and injectors out evenly.
8. CAUTION
9. Remove the fuel rail assembly carefully in order to prevent damage to the injector electrical connector terminals and the injector spray tips. Support the fuel rail after the fuel rail is removed in order to avoid damaging the fuel rail components.
10. Cap the fittings and plug the holes when servicing the fuel system in order to prevent dirt and other contaminants from entering open pipes and passages.
11. 1. Simultaneously lift both ends of the fuel rail?(2) and remove the fuel rail assembly from the cylinder head.
12. Remove and DISCARD the fuel injector seals.
13. Some vehicles were not originally equipped with fuel injector dust seals. A NEW seal must be installed when the injectors are removed.
    Remove and DISCARD the fuel injector dust seal (1).
14. NOTE
    Note
    Whenever the fuel injectors are removed from the cylinder head or fuel rail, they will need to be rebuilt. Fuel Rail and Injectors Cleaning and Inspection
    If replacing the fuel injection fuel rail, remove the fuel injectors. Fuel Injector Replacement

Installation Procedure, skipped me. the service manual lists 4 tools
per

Special Tools

1. EN-49248 Injector Rail Assembly Remover
2. EN-51105-1 Injector Seal Installer and Sizer
3. EN-49245-3 Fuel Injection Seal Installer Sizer
4. EN-49245-4 Fuel Injection Seal Installer Sizer

this is first. pull the isolator.

this one step is the GET TO ANSWEREd
Injector work 10x more complex and special tools needed x4

Check fuel pressure at the injector rail. Watch it until the car dies. Also check to make sure injectors are not shutting off. Should be clicking as you try to start, even after the car dies. Could be a fault in the security system.

old post but see it asked many times.
assemble the rail first, its 1 piece so must be ready first.
3.7L Engine (FSM) RTM?
(1) If fuel injectors are to be installed, refer to Fuel
Injector Removal/Installation.
(2) Clean out fuel injector machined bores in
intake manifold.
(3) Apply a small amount of engine oil to each fuel
injector o-ring. This will help in fuel rail installation.
(4) Position fuel rail/fuel injector assembly to
machined injector openings in cylinder head.
(5) Guide each injector into cylinder head. Be careful
not to tear injector o-rings.
(6) Push right side of fuel rail down until fuel
injectors have bottomed on cylinder head shoulder.
Push left fuel rail down until injectors have bottomed
on cylinder head shoulder.
(7) Install 4 fuel rail mounting bolts and tighten.
Refer to torque specifications.
(8) Install 6 ignition coils. Refer to Ignition Coil
Removal/Installation.
(9) Connect electrical connectors to throttle body.
(10) Connect electrical connectors at all fuel injectors.
To install connector, refer to (Fig. 37). Push connector
onto injector (1) and then push and lock red
colored slider (2). Verify connector is locked to injector
by lightly tugging on connector.
(11) Connect necessary vacuum lines to throttle
body.
(12) Connect fuel line latch clip and fuel line to
fuel rail. Refer to Quick-Connect Fittings.
(13) Install air box to throttle body.
(14) Install air duct to air box.
(15) Connect battery cable to battery.
(16) Start engine and check for leaks.

If gas is getting to the fuel rail, it is getting to injectors. If fuel pressure is good, probably the injector circuit is not working. With a test light you can check the injector circuit. Post back for further help. What year and make is the car?

This will provide a basic how to or DIY on how to replace your injectors, but for your specific application, we recommend you ask in our car forum.

Before You begin, It is essential to de-pressurize your fuel system. Disconnect the power to your fuel pump, by either disconnecting it's power supply, or pulling the fuel pump fuse or relay. Once the fuel pump has no power or relay installed, crank the engine for a few seconds. The engine might start, but should die a few seconds later. If it continues to idle, then you didn't disconnect your fuel pump or the correct relay.

Once the fuel system is de-pressurized, you can begin to remove various parts from the engine bay to help clear up room. On a typical system, there is a fuel feed, and fuel return. For these types of systems, you would need to disconnect both of the lines, and then disconnect the fuel pressure regulator. The fuel injectors are held in with clips that hold the harness to the injector. Remove these clips, and pop off the wiring harnesses. The fuel rail is held in with a few bolts. Remove these bolts, and then the fuel rail should be loose. Pull the fuel rail out of the intake manifold or cylinder head, and you can now easily remove the fuel injectors.

Make sure to cover the holes that are now in the intake manifold or head. Don't let any debris fall into this hole!

Pull the old fuel injectors out of the fuel rail, and then put the new injectors into the fuel rail. Make sure you have new "o" rings and you are all set. Simply put everything back together, and then don't forget to plug your fuel pump back in. The car may be hard to start the first few cranks as the fuel pressure builds, and then you are all done!


Diagrams for the above can easily be found in a Haynes or Chiltons Manual - Failing that look on the web, Best of luck.

Assuming the injectors are already installed in the fuel rail, put a little fuel on the injector seals, position the injector rail in front of the holes in the head.
Start from one end of the rail and work the first injector into its hole a little bit, but not all the way. then do the same for the second and third. Work them in a little at a time so the injectors dont come loose from the fuel rail.
Once you get all injectors completely into the holes, rotate each of them back and forth until the injector turns smoothly when you rotate it. Once an injector rotates smoothly its seated correctly. But only rotate them a small amount back and forth.
If the injectors are removed from the fuel rail, do it the same way. Just install them in the fuel rail first, then install the rail/injectors into the cylinder head.

I think you right in your thinking by replacing the plugs. My guess is that an injector is partially blocked. Remove the fuel pump relay and take the vacuum hose of the pressure regulator on the end of the fuel rail. Try to start the engine to relieve pressure from the system. Remove the air cleaner ducting. Open the fuel filler cap for a second to relieve any pressure in the tank. Disconnect the fuel supply and fuel return pipes to the fuel rail. Unbolt the fuel rail mount, disconnect the injector electrical connections and ease the injectors out. Take care with the wiring some of the insulation can become brittle. The injectors are held in the intake manifold by 'O' rings and likewise to the fuel rail; securing clips ensure that the injectors are held securely to the rail. Wash and back flush these babies until you are happy they are clean and free of obstruction. Also check the fuel pressure regulator, it is rare for these to fail but its worth checking. Dry everything off. Apply a little oil to the 'O' rings prior to reassembly. If the problem persists at least you can cross this area off your list.

ok could be a few things.

Have you changed the inline fuel filter? these usually have paper filter elements and after a while can be clogged with moisture which blocks fuel flow. The fuel pump will still have good pressure but the fuel rail will lack the flow required and you may burn out an injector as its running too lean. Secondly, the MAF sensor, could be dirty, clean it with electrical cleaner.

I think its more likeylt the fuel filter blocked. Try and bypass it if possible, reset the ECU and try agiain

Are you sure you have correct timing? its definetly a fule problem, if timing is good then turn your key to the on position and try to listin for the fule pump to prime. While the key is in on position go to fuel rail, there is a valve on fule rail called sharader valve. Get a small screw driver and press valve in to check if car has fule pressure. if pressure is present then it is incorrect timing or possible bad cam sensor.

gthr