Question about 1997 Geo Tracker 2 Door

1 Answer

I put a rear seal in a 1993 geo tracker,was not leaking,now i have put two seals in ,still leaking

I put in new clutch .i changed the rear seal.it leaked.i put another it is leaking i put a oil pan gasket on still leaking can you help?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Geo Master
  • 20,706 Answers

Which seal. ? rear of WHAT?
2wd, 4wd?
3sp,4speed or 5sp. tranny.?
my wild guess, is the rear transfer case leaks, and if yes, where.?
it can leak in 3 places. (ive rebuilt them and the boxes)

or the rear engine seal.

so the rear seal can be, in 3 places.
if you work on 4wd, it really can be 5 places.
6 counting rear of front axle.
that is because the exit paths are shared on many.

first tell me what you are driving like this.
97 geo 2dr, 5sp 4wd. like that, then we can answer in fine detail.

http://www.fixkick.com/

Posted on Oct 05, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 59 Answers

SOURCE: How to Replace the crankshaft seal on a geo

Not sure about your model but here is a Nissan Sentra. Might be similar. You decide.

Seal is behind belt pulley mounted in the timing cover. It actually seals to the shoulder on the back of the pulley (harmonic balancer), not the crank shaft. Use a special pulley removal tool, NOT a hammer or crowbar to remove. Breaks easy and is expensive to replace.

Posted on Sep 21, 2009

  • 137 Answers

SOURCE: 4 auto

but a seal puller is $5 and one can use a ice pick and punch a hole into the seal . then screw in a wood screws in the hole and pull it out.
just careful removal , no hurry.
the real problem is never put the seal back on unless you cover and protect the crank lip, this lip has a 100% seal destruction record.
suz stopped selling their $2 protecter so i use electricans tape.

no when you put the crank cog back on , be sure to use
a new factory bolt , they streatch , and set the torque 17mm bolt to 94 lbs/ft ( new TSB spec)

its all here on my page
http://www.kick-fix.com/t-belt/tbelt.html

Posted on Oct 22, 2009

kozachek
  • 122 Answers

SOURCE: Hard shifting

Are you sure that it is oil and not transmission fluid? The stains can look similar unless you actually get down and touch the fluid. If it is reddish in color then it is transmission fluid, which means you have a leak somewhere in the transmission. Either way, check your transmission fluid level and make sure it is not low. If it is is low, add some fluid and bring it to a transmission specialist to help diagnose and correct the problem.

Posted on Nov 07, 2009

  • 427 Answers

SOURCE: 1993 Geo Tracker leaking water from upper middle

I would check hoses and water pump. When water pump goes bad it leaks water out hole out of bottom.Get pressure pump and pump up system it makes it easier to find leak.

Posted on Jul 16, 2010

mickha2
  • 145 Answers

SOURCE: how to Replace the crankshaft seal on a 1997 geo tracker

remove belts, pull out crankshaft pilley and then pull put seal

Posted on Aug 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Oil leak on a '92 Geo Tracker. Installed an O Ring, but still leaking. Any suggestions?


O-ring where? The drain plug? Distributor shaft? Or do you mean oil seal?
Geo oil drain plug specifies a compressible copper ring washer I think? Need to clean the surfaces well, and torque to spec. My own plug's seal is not perfect, but only a drop here and there usually. Autozone or NAPA can supply you a new plug and washer if needed.

Apr 19, 2015 | 1992 Geo Tracker

1 Answer

How to replace main engine seals on 1.6l geo tracker


old post (WHICH TRANSIMISSION? AND 2WD OR 4WD?)
its not bad, seen many replace mains for no gain,, vast....
on many forums.whe do that.(if a/t is oil ATF)
and were wrong every time.
the reaR VALVE COVER GASKET LEAKS, skipping 60k mile service is Reasn.
THE 2 DISTRIBUTOR O-RINGS LEAK , ALL DO THIS ,this OLD
a FACT
AND This oil then runs down back top of BELL
the finds the magic secret, suzuki bell vent (gravity is a beach)
and then runs into said vent and fools all owners that rear seal leaks(even me.... )

see this.
http://www.fixkick.com/engine/97-motor-pull/HTML/image_5.html

all that oil ,is VC gasket and distib 0-rings bad.
every drop..
this be first.
ask how to fix both , have links to all pages

Feb 16, 2014 | 1993 Geo Tracker

1 Answer

I have 1994 geo tracker, i have to replace oil pan as it is corroded and leaking oil. Do i have to pull the engine out to remove oil pan or is there another way to do tjhis?


there are 2 ways, and both are here.
pull engine
pull axle
it;s your choice, and covered here and the factory service book too.
depends on tools, (lift?)

way 1
http://www.fixkick.com/axles/Pan-drop/pandrop.html

way 2: (factory way)]
here is the pull page. engine
and last link there is to fsm page on same.

happy trails.
PS
99% of leaking pans, are NOT.
it is :
1: valve cover leaks, (not doing 60k service and not putting in new VC)
2: cam seal leaks.
3: crank seal leaks.
4: the infamous, dizzy 2 o-ring leaks.
5: and doing head rebuild, they forget to read the page on how
to seal the rear cam cap. and bam, it leaks, the FSM covers that.
i can tell you which page.\
and gravity does the rest with help from mr. wind.

if the pan is only rusty, hit it with phosperic acid (ask) and then paint it on car. the PAN is RTV glued to the engine are never leak. (almost)
and are real hard to get them resealed , leak free. so makes sure
it really does leak.

Feb 10, 2014 | 1994 Geo Tracker

1 Answer

I have a 94 geo tracker and can't get rear axle off


there are no pins, more like my chev, PU.
the steps are all here, and some nice tricks.
the steps are also in alldata dot com and
in the fsm.
http://www.fixkick.com/axles/axle_rear_R&R.html

you could read chapter 4b. its there too.
with errors
http://www.acksfaq.com/trackerfsm.htm

Mar 14, 2013 | 1994 Geo Tracker

1 Answer

Oil leak front engine timing chan


1995 Tracker would have a timing BELT. Normal oil leak points (in order) on a Suzuki G16 engine are the distributor base (rear of motor), valve cover (top of motor), front main seal (behind lower timing belt cog) cam seal (behind the upper timing belt cog) and rear main seal. (behind the flywheel). I'd suspect the front main seal or cam seal. I use foot power to help find oil leaks.

Dec 24, 2012 | 1995 Geo Tracker

1 Answer

I have a 1990 Geo Tracker 4X4 with a manual transmission. Overall the vehicle is in excellent shape. It has been pulled behind a motor home and has 160,000 on the odometer -- about 70,000 of this was...


I would be more concerned about what you put in it,
than the leak
I would never use a sealer even if they worked
I would say pull the trans & try a different brand seal,
and do the work yourself
You can not be having a vehicle that old or any vehicle
worked on ,if you have to pay someone
The cost is too much & quality of work worse

Aug 04, 2011 | 1993 Geo Tracker

1 Answer

How do i replace a water pump on a 1993 geo


1 disconnect battery ground cable
2 drain cooling system
3 on models with a/c, proceed as follows:

a discharge a/c system
b loosen upper and lower compressor bolts and remove compressor drive belt
c remove a/c line from top of radiator shroud

4 remove water pump drive belt
5 remove reservoir tank from radiator bracket
6 remove radiator shroud and fan/clutch from vehicle
7 remove waterpump pulley from waterpump
8 remove timing tensioner and timing belt
9 remove dipstick tube
10 remove alternator mounting bracket at water pump
11 remove water pump mounting bolts and water pump
12 reverse procedure to install, using new gasket and rubber seal

Feb 18, 2010 | 1993 Geo Tracker

3 Answers

White smoke coming from my 95 Geo tracker, Standard shift, only on start up any ideas. Just had a tune up, new clutch, and cable.


most deffinately an internal issue. 2 possible problems oil seeping through valves when engine not running. sitting in combustion chamber and burns off during start up. 2 piston rings in one or more cylinders bad and letting oil blow by and start up is only time it is really noticeable.

Oct 09, 2009 | 1995 Geo Tracker

1 Answer

How to Replace the crankshaft seal on a 1997 geo tracker


remove belts, pull out crankshaft pilley and then pull put seal

Sep 21, 2009 | 1997 Geo Tracker 2 Door

1 Answer

Back window leaks


JUST look and see, when raining? really !

THE TOP REAR , Window fits to a abar that fits to a long bar,
when the rear door closes , it seals against this bar, and there is a seal.

if no seal then go to GM or Suzuki and ask for seals.

Mar 28, 2009 | 1995 Geo Tracker

Not finding what you are looking for?
1997 Geo Tracker 2 Door Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...