1998 Isuzu Truck Rodeo 2WD 2.2L MFI DOHC 4cyl
The Head Bolt Torque
Torque sequence ----------------- front ' 7 3 1 5 9 ' of ' ' engine ' 8 4 2 6 10 ' ----------------- Step 1: torque bolts in sequence to 18 Ft/Lbs Step 2: turn bolts in sequence an additional 90-degrees Step 3: turn bolts in sequence an additional 90-degrees Step 4: turn bolts in sequence an additional 90-degrees recheck final torque in sequence
1998 Isuzu Truck Rodeo 2WD 3.2L MFI DOHC 6cyl
The Head Bolt Torque
Torque sequence -------------- front ' 6 1 3 7 ' of ' ' engine ' 5 2 4 8 ' -------------- Step 1: torque to 20 Ft/Lbs Step 2: torque to 47 Ft/Lbs recheck final torque in sequence
SOURCE: timing settings for a 1998 isuzu rodeo
You didn't say whether you had a V6 engine or a 4cyl. Here is the procedure for a V6.
It sounds like he moved the cam shaft independently of the crankshaft or other camshaft so you will need to do all these procedures:
1. Turn the crankshaft until the mark on the spocket is lined up with the mark on the oil pump housing (the mark is on the driver's side at 90 degrees to the sprocket itself).
2. Back off the crankshaft counterclockwise 1/8 turn to ensure the pistons aren't at top dead center. This gives the valves room to move without hitting the piston.
3. Turn the passenger's side camshaft until it "jumps" into place with the alignment mark on the camshaft pully is pretty close to being lined up with the mark on the engine head.
4. Turn the driver's side camshaft until it "jumps" into place but this won't be perfectly lined up with the mark but will be about an 1/8 turn off from the mark. Then line it up by hand.
5. The idler pulleys and tensioner pulleys should be installed on the engine but the tenioner pulley adjuster (it is a little cylinder with a rod coming out of it that is held in place by 2 bolts) should be removed.
6. Place the new belt on the crankshaft first. Be sure the arrows on the belt point in a clockwise direction. If you have a belt with lines and dots then the lines will line up with all markings that you have lined up together. The dots should line up at the 270 degree point on the crankshaft (opposite of the lines and the markings).
7. Loop the belt around the tensioner pulley, around the passenger's side cam, under the waterpump, around the driver's side cam, and finally around the idler pulley. Check all alignments.
8. Put the tesioner adjuster in a vise and squeeze it together until you can place a small drill bit or allen wrench through the holes to keep it compressed.
9. This is the tricky part. You will need to install the tensioner adjuster and that will require some moving of the belt to allow enough play to get the adjuster in place. This may move the passenger's side alignment. If so, you will need to try it again. I find that if you move passenger's side alignment mark clockwise by one tooth of the sprocket, then when you go to put the tensioner in place it lines up. You may find other tricks to overcome this challenge.
10. Once you think you have everything lined up. Use a wrench to turn the crankshaft sprocket 2 full turns. Listen closely and feel for any hard resistance as you do this to determine if the pistons are hitting the valves. If you believe they are hitting each other thenrepeat the adjustment procedure. Not doing this can ruin the valves or more.
11. If everything seems OK. remove the drill bit or allen wrench from the tension adjuster. Perform step 10 again for one final check.
I hope this helps.
SOURCE: 1992 Isuzu Rodeo Distributor wires
Hi,
On the 3.2L distriburorless ignition, the firing order is a straight 1-2-3-4-5-6.
Cylinder numbering .
-
Hope this works for you
SOURCE: what is the 98 isuzu rodeo head bolt torque
joyce, there are different specs for sohc and dohc engines. my advice is to get a Haynes manual from the auto parts store.
doug
SOURCE: cylinder head torque settings 1990 2.6L isuzu motor
From front to back is this:
7 3 1 5 9
8 4 2 6 10
First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.
SOURCE: I need the torque settings for the cylinder head
http://www.autozmagz.com/isuzu/2000-isuzu-trooper-s-torque-specifications/
try here and see if they can help. You can download manuals for free here.
Fig.: Cylinder head bolt torque sequence-2.2L engine
Apply a coating of 1052080 or equivalent sealer to the cylinder
head bolt threads. Install the cylinder head bolts (within 15 minutes of
sealer application), then tighten them in the proper sequence first to a
torque of 46 ft. lbs. (63 Nm) for long bolts or to 43 ft. lbs. (58 Nm)
for short bolts and then tighten all bolts an additional 90 degree turn
using a torque angle meter.
Hope this helps (remember to rate this answer).
3,325 views
Usually answered in minutes!
×