Mazda 6 windsceen/rear window washer low pressure

Windshield Washer Pump and System Diagnosis - YouTube

? 10:00
https://www.youtube.com/watch?v=0SdUhyQF4tY
Sep 9, 2012 - Uploaded by RatchetsAnd Wrenches
You'd think the pump would run continuously, but it doesn't run at all. .... Do some cars have a separate fluid pump for front and rear washer nozzles or is it always the same pump that makes both front and rear work? Thanks ...

Windshield Washer Repair ' The Family Handyman

www.familyhandyman.com > Skills > Automotive

... or a dead pump. Here's how to diagnose and fix both problems. ... TypicalWindshield Washer. Follow the ... If you hear the pump going but don't get fluid, you probably have clogged nozzles. Lift the ... If it doesn't, replace the pump. The main ...

How to Troubleshoot a Windshield Washer Pump: 8 Steps

www.wikihow.com > ... > Auto Exterior and Interior Accessories

wikiHow

Be carefull remove the w washer hose on nozzle they break easy try heating that little hose a bit its easyer to remove after you did remove spray air from the outside on the nozzle on the hood or bonnet for u debrie will come out make sure its clean reinstall
And try it

use a tiny needle to cleardirt on the holes on the sprayand nozzles you can even adjust the nozzles using the very same neddle by moving the needle to the correct direction that you like it to spray . Pull the hose off the nozzle and check water pressure and see if fluid comes outt, the line may loose pressure or blocked, not the nozzle.
If the line is good than revert back to adjust the spray nozzle using the niddle by putting niddle in the holes of the nozzle and adjust by moving it up and down or left to right it must work..

A likely source of the problem is a plugged line or nozzle. Nozzle is easiest problem to fix. Disconnect hose is you have access and see if water pumps. If it does then replace or clean nozzle. Cleaning nozzles may or may not be easy.

It sounds as though their is a short, loose connections, or the water punps for these are out.
Inquire with a technician for diagnostic options.
carsandcomps

PROBABLE CAUSE Impact to the front bumper pushes the bumper back far enough to break the washer pump hose fitting. CORRECTIVE ACTION Replace the windshield washer reservoir and washer motor with updated parts. REPAIR PROCEDURE 1. Turn the ignition switch to ACC (I) to unlock the steering column. 2. Raise the vehicle on a lift. 3. Remove the right front inner fender. Unhook and pull back the bumper for better access. CLIPS (6 places.) SCREWS (6 places.) RIGHT FRONT INNER FENDER 4. Release the hooks on the upper right side of the front bumper. 5. Remove the clip from the filler neck, then remove the filler neck. FILLER NECK CLIP WINDSHIELD WASHER RESERVOIR CLIP WASHER MOTOR CONNECTOR BOLT BOLTS WASHER TUBES 6. Remove the right front fender trim, and disconnect the washer hose from the 90-degree fitting. CLIP FRONT FENDER TRIM FRONT HOSE 7. Disconnect the 2P connector and the two washer tubes from the washer motor. 8. Remove the washer reservoir clip and the three bolts, then pull out the reservoir. 9. Assemble the new reservoir components, but do not install the filler neck. 10. Trim 85 mm off the end of the 1,260 mm washer tube only. 11. Route the washer tubes on the reservoir. NOTE: The black fitting is for the front windshield nozzles, and the white fitting is for the rear nozzle. 85 mm 12. Install the reservoir. 13. Connect the rear tube to the straight fitting in the wheelwell. 14. Connect the 2P connector to the washer motor. NEW RESERVOIR Connect the rear washer tube. CLIP BOLT 9.8 N•m (7.2 lb•ft) 15. Install the filler neck with the original clip. Connect the front washer tube to the 90-degree fitting. Then reinstall the front fender trim. WASHER FLUID DIPSTICK 2P CONNECTOR FRONT FENDER TRIM FILLER NECK CLIP

The front washers fill up near the left side step. the rear has its own resiviour and pump

you need to remove it. its located under the wheel arch on the same side as the water tank.

its not a servo it is a pump motor
check the fuse if ok ck. for power at the rear pump motor

If it is the same as some other Chevrolets they have 2 pumps attached to the side of the washer bottle. 1 for rear and 1 for front windscreen