License plate bulb

The license plate lamps are designed to illuminate the plate and registration tags on your vehicle and make it easily visible to law enforcement. In many states, a burnt out license plate bulb can get you a ticket.
Step 1: Locate the license plate light. The license plate light is located right above the plate.
Step 2: Determine which bulb has failed. Park your vehicle and set the emergency brake. Turn the ignition to the Accessory position and turn on the driving lights. Walk around the vehicle to determine which license plate bulb has failed.
Step 3: Remove the license plate light cover. Remove the license plate light cover retaining screws using a screwdriver.
Remove the license plate light cover.

• Note: You may need to use a small screwdriver to pry the cover off.

Step 4: Remove the bulb. Remove the bulb from its retainer.
Part 2 of 2: Install the bulb Materials Needed

• Protective gloves
• Replacement license plate light bulb
• Safety glasses
• Screwdriver

Step 1: Install the new bulb. Install the new bulb in its retainer and ensure it is in place.

• Tip: Refer to your car's user manual to determine the correct type of light bulb to get for your specific vehicle.

Step 2: Complete the installation. Put back the license plate light cover and hold it in place.
Install the license plate light cover retaining screws and tighten them using a screwdriver.
Step 3: Check the lights. Turn on your car to check if your license plate lights are fully functional.

If it is not possible to take the lens off from the outside. (this is the normal way on most cars) Open the tailgate and remove the whole interior panel. Its not as hard as it sounds. This should allow access.

Hello: Remove the license plate, then remove the screws on the chrome piece behind the license plate and the you can access the bulbs.

YOU HAVE TO OPEN THE TRUNK LID REMOVE THE BLACK PLASTIC COVER FOR THE TRUNK LID LATCH.REMOVE THE LICENSE PLATE LIGHT HOUSING FROM THE TRUNK LID.REMOVE THE BULB SOCKET FROM THE LICENSE PLATE LIGHT HOUSING.TO REMOVE BULB FROM THE SOCKET SIMPLY PULL IT STRAIGHT OUT OF THE SOCKET.

Look at where the (3) lights come together, just above the lower light, and in the seam between the headlight and side marker. There is a small screw hidden in there. A "T-20" I believe. Remove that screw and persuade (gently but firmly) the side marker to come out.

You should have two license plate lights, right above the license plate. If you remove the two screws that hold the one you want to change in, the entire fixture will drop down(best to do this with the trunk open). Remove the metal clip plate that covers the bulb. The bulb SHOULD simply pull directly out.
Hope this helps you.

LICENSE PLATE LAMP BULB
REMOVAL

1. Remove screws attaching license plate lamp to rear bumper
2. Remove lamp from bumper.
3. Remove bulb socket from lamp.
4. Pull bulb from socket.

INSTALLATION

1. Install bulb into socket.
2. Install bulb socket into lamp.
3. Place lamp in position.
4. Install screws attaching license plate lamp to rear bumper.

remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the bulb.it should pull straight out

It wouldn't be a fuse if that's the only light that's not working, I believe all of the parking lights are on the same fuse. It's most likely a bad ground or corrosion inside the socket where the bulb makes the electrical connection. So check the socket to make sure it has no corrosion, if it does, clean it up and apply some dielectric grease (available at any parts store) to prevent future corrosion, and check for a loose or broken ground wire.

I'm not to sure what one you did want license plate light or the tag light up high above your back door. I know I am reading license plate so I will say the fuse needs to be replaced. plate lamps need 2 light bulbs and the fuse box is under the steering wheel or under the hood there are 2.
in my book it said that it is a (194 trade number), I woulds change out bulbs and then fuse.