2003 Pontiac Grand Am Logo

Related Topics:

A
Anonymous Posted on Jan 22, 2018

2003 grand am won't start

Turn key dash lights up, has good power, lightrs work etc.... but engine will not turn over.Changed the starter still won't tun over. can be started by making connection on the starter with a screw driver. wiggled wire on the brake switch and it worked for two days and now won't work again.

5 Related Answers

A

Anonymous

  • Posted on Oct 17, 2008

SOURCE: 1999 pontiac grand prix . will not run

If wiggling the wires cured the code, then one of the wires is broken inside the insulation. Pull on each wire one at a time. look for the colored insulation to stretch, this will be the broken wire. For the other car that wont rev up, this is a common when the catalytic concverter is plugged up. This will also cause MAF codes, and in turn, TRAC OFF light.
See http://www.greatautohelp.com

Ad

Anonymous

  • 1 Answer
  • Posted on Dec 12, 2008

SOURCE: 2001 pontiac sunfire wont start

I have had the exact same problem. There is an ignition lock that probably went off. There is a fuse box under the hood. The fuse that says ignition on it pull it out and put it back in. This should reset the ignition lock. Its a safety feature because the car thinks that someone was trying to tamper with it.

Anonymous

  • 426 Answers
  • Posted on Dec 28, 2008

SOURCE: Grand Prix wont start

Try checking the starter solenoid wires.Make sure the wire hasnt come loose and the battery to solenoid cable is tight.

Anonymous

  • 4803 Answers
  • Posted on Feb 08, 2011

SOURCE: 03 grand am 3.4l no crank at all. All the light

If the Passlock switch has been replaced, the computer has to "learn" the new Passlock code. You will need to hook up a battery charger to perform the learning process. (It takes about 30 minutes with the key in the "ON" position and it will run the battery down.)

Step 1:

Turn the key to the "START" position and release to the "RUN" position. The "SECURITY" light will be flashing. After about 10 minutes, the light will stop flashing.
.
Step 2:

Turn the key "OFF" then back to the "RUN" position. (Do NOT try to crank it yet) The light will start flashing again. Wait about 10 minutes for it to stop flashing.
.
Step 3:
.
Turn the key "OFF" and back to "RUN" one last time. The light will be flashing again. This time, when it stops flashing, do not turn the ignition off. Instead, turn the key from the "RUN" position to "START". The engine should start and run. The computer has now learned the new Passlock code.

Please help myself and others by taking the time to rate my answer. Thank yoou for using fixya!

Anonymous

  • 334 Answers
  • Posted on Feb 17, 2011

SOURCE: I have a 95 firebird.

It's when the security light starts flashing that the infamous "chip" in the key becomes a nightmare to many. Gradually the car begins not cranking anymore or if it cranks it would start and die in a second. Randomly it will do this more and more often until it won't start anymore. VATS, PASSkey and Passlock immobilizer systems are killing cars all over North America, they have a short lifespan and are certainly more effective against owners than thieves. Here is how you save your car
1st trick, Try a spare key that is newer or used less. The pins wear down and so do the keys causing security fail. 2nd trick, (if not starting) turn the key forward 2 clicks till right before it would normally start, leave like that for 10 minutes. ( no less ) After 10 minutes, turn key back then forward and your car might start. I did this in my regal for more than a year. If its shutting down while running, im sorry i have no quick fix... If anything on this page helps you, please remember to comment or give me a thumbs up on the myfixya sight so i can have a better rating to help more people on this. Thanks

Cheap fix: Bypass the chip in your key. Temporary, but effective. Until the TDM (theft deterrent module) in the dash poops out, then you're kinda screwed. I was told that these types of key security systems have a 7-10 year life span. Sucks for us. This link explains the "Key Issue" pretty well.
----- http://vats.likeabigdog.com/


Never worry again fix: Bypass the whole VATS/Passlock/passkey I or passkey II system entirely. Literally take it out, and throw it away. I just did this in my Regal. Took about an hour. Took longer to find the thing than it did to fix the problem. They sell a unit for 200 bucks to totally bypass this system FOREVER. life time-money back and all that. Finally did this in my car. Well worth the 200 if you've looked into getting this replaced... Anywhere from 600-1000 bucks. If you do buy this, please purchase it thru this link. The cost is the same, but i get credit for the sale and im trying to earn my money back, as you will be able to do if you buy fron NewRockies and join the free affiliate program. Thanks
----- http://newrockies.ca?ap_id=judd0081 ----- With this fix, you can take that whole Vats, passlock, passkey system out of your car all together. Good info on both sites.

It works for:
Any GM or Isuzu Vehicle with VATS or PASSKey or PASSLock security systems.
If your car has the chip in the key or in the lock cylinder, then you can save it with this Full Bypass.
Trucks
.
GMC/Chevy
1998-2006 S10/T10/Sonoma
/Blazer/Jimmy
1998-2007 Suburban/Avalanche
/Tahoe/Yukon
1998-2006 Sierra/Silverado
2002-2008 Trailblazer
2003-2006 SSR
1998-2006 C1500/C2500/C3500
1998-2006 K1500/K2500/K3500
2003-2007 Hummer H2
.
Isuzu
1998-2000 Hombre
2005-2006 I280/I350
2007-2008 I290/I370
.
Cars/Vans
.
Isuzu
2003-2007 Ascender
.
Pontiac
1994-2003 Grand Prix
1998-1999 Montana
2006 Torrent
1996-2005 Grand AM
1994-1998 Trans Sports
1988-1999 Bonneville
1988-2002 Firebird
1995-2005 Sunfire
1996-2002 Trans Am
.
Buick
2004-2007 Rainier
1994-2005 Century
1993-2004 Regal
1982-1999 LeSabre
1991-1996 Park Avenue / Ultra
1994-1996 Roadmaster
1991-1996 Roadmaster Estate Wagon
1982-1999 Riviera
1988-1991 Reatta
1996-1998 Skylark
1982-1990 Electra (all models)
.
Oldsmobile
1996-1998 Achieva
1999-2004 Alero
1994-2004 Aurora
1998-2004 Bravada
1991-1993 Delta 88
1994-1999 Eighty-Eight
1991-1996 Nighty-Eight
1998-2002 Intrigue
1990-1992 Toronado
1994-1997 Cutlass Supreme
1997-1999 Cutlass
1997-1999 LSS/Regency
1997-1999 Silhouette
1991-1996 Custom Cruiser
.
Chevrolet/GMC
1998-2005 Astro/Safari
1998-2008 Envoy
2005-2006 Equinox
1998-2007 Savana/Express
1995-2005 Monte Carlo
1997-1999 Venture
1995-2001 Lumina
1988-2002 Camaro
1995-2005 Cavalier
1982-2004 Corvette
1994-1996 Caprice/Caprice Wagon
1995-1996 Impala SS
2000-2005 Impala
1997-2005 Malibu Classic
1997-2003 Malibu
.
Cadillac
1986-1993 Allante
1982-1996 Fleetwood
1985-1996 Fleetwood Brougham
1992-2004 Seville
1992-2004 SLS/STS
1985-1999 Deville
1994-1999 Deville Concours
1997-1999 Deville D'Elegance
1988-2002 ElDorado
1994-2002 ElDorado Touring
1999-2007 Escalade
.
Saturn
2000 LS/LS1/LS2/LW1/LW2
2001-2002 L100/LW100
2001-2003 L200/LW200
2001-2005 L300/LW300
2004-2005 L-Series
2002-2008 VUE
1996-2002 SL/SL1/SL2
1996-2002 SC1/SC2
1996-2002 SW1/SW2

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2003 Ford Focus Engine won't turn over

Try crossing the starter wires, it should turn over. Is key ok, maybe its not coded? Also check connectors on starter . Try disconnecting battery for 30 mins, might reset electrics.
2helpful
1answer

MY PLYMOUTH GRAND VOYAGER 'S HEADLIGHT'S AND DASH LIGHTS WORK, BUT THE ENGINE WON'T TURN OVER. THERE IS NO SPARK COMING FROM THE ELECTRICAL WIRES.

When you say no spark, are you talking about the spark plugs, or just the general wiring?

If the engine won't turn over, then it isn't moving, and if it isn't moving then you need to check the following in this order:

1) Does the battery have power i.e. around 12.4 volts or over?No? Charge, test or replace battery.

2) Do the car's head lights dim considerably if turned on when attempting to crank? Yes? Possible lack of battery charge or faulty battery.

3) Assuming the battery is fine, can you turn the dash warning lights on and off with the key? No? Faulty ignition switch.

4) Is there a click sound when you turn the key, but no starter motor spin? Check starter motor connections or replace starter motor.


If none of the above prove to be of help, then please report.
0helpful
1answer

2003 lexus es300 won't start... radio lights and windows work. Tried a jump start, still doesnt work...

Are you saying the engine cranks but won't start, or the engine won't crank ?
If the engine does not crank, you would check for voltage at the starter, the neutral safety switch, and the key switch as well as the ground connections.
0helpful
2answers

I got a 1999 chevrolet tahoe. when i put the key in the ignition the head lights,and the dash light comes on but it won't even turn. i change the starter and got a new battery and it still won'

well if you have a dvom/voltmeter check the power at the starter terminals. the main terminal should have power all the time the key wire should have power only when the key is turned to crank engine. if you have power at both then i would start looking at grounds
2helpful
3answers

2007 grand prix won't start but lights and horn work

Your battery is to low on power it needs a good charge, or replace it is the best option for a brand new one!
0helpful
3answers

2009 HHR won't start. Battery is good.

Is the security light on or blinking?If not then do you have power to the starter.You can check this with a test light.You should have power when you turn the key to start.The test light should light up.Should be the small wire.I believe it is purple in color.If the security light is on then you will have to get the codes to see what is causing the no start.Hope this helps.Good luck.
0helpful
1answer

2002 hyundai Santa fe will not start. I turn key and starter turned for 3 seconds then stopped and now when i turn key NOTHING. I hear a circuit sound in back of car when i turn key but no other sound. ...

Definitely a starting system problem. That sound you hear in the back is the fuel pump.

Starting system circuit components (besides wiring harness)
1. Ignition Key Switch - closes the starter relay control circuit to energize the relay and close the contacts inside the relay (you can check this by locating the relay in the underhood fuse/relay box and have a friend turn the key while you listen/feel if the relay 'clicks'
2. Starter Relay or its Contacts
3. Starter Solenoid - pushes/pulls the starter gear into the engine's flywheel ring-gear and its contacts close to provide battery power to the starter itself.
4. Starter itself - poor brush contact with the armature's commutator will prevent the starter to spin/turn

If you are 'Electrically' talented, you can check to see if you're getting battery power to the starter solenoid by using a simple 12 volt test light/bulb. Connect one lead to the starter solenoid terminal and the other to chassis/engine ground and have a buddy turn the ignition key - if the light turns 'ON', then you know that particular circuit is OK but the starter solenoid is not energizing to push the starter gear into the flywheel ring-gear to turn the engine over. If it doesn't, the problem is elsewhere (wiring, starter relay, starter relay control circuit, etc).

You can have a qualified Hyundai Service Technician properly diagnose your vehicle. OR, you can Go to www.hmaservice.com and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop manuals, service bulletins, illustrations, etc.
1helpful
1answer

I have a 96 pontiac grand am that doesnt start all the time

Starting Problem # 1: Engine Won't Crank At All

Scenario: You turn the key, but nothing happens: And by nothing, we mean there is no dash light, no sound, nada. The first thing you should do in this case is to pop the hood and check the battery. Either the battery is completely dead or there's a wiring problem in the starting system. Try jump-starting the battery. If that doesn't work, you'll probably have to call for assistance.

Scenario: When you turn the key, you hear a rapid clicking sound, and the dash lights dim. This is your classic low-battery symptom. Jump-starting the battery should get the engine to start.However, if you keep experiencing this problem, you could have a bad battery or alternator, or it could be some­thing as simple as a loose alternator belt. Take your car to a mechanic just as soon as you can.

Scenario: When you turn the key, the lights on the dash come on, but you don't hear anything. Make sure you have the shift selector all the way in park. Move it out of park and then back, or try starting it with the shifter in neutral. If your car has a manual transmission, make sure you have the clutch pressed all the way to the floor. If that doesn't help, you can try jump-starting the battery, but it probably won't work. There's a good chance your car has a bad starter or a problem in the starting circuit. That could mean a prob­lem in the ignition switch, neutral safety switch or starter sole­noid.

Scenario: The dash lights come on when you turn the key, and then go right out, and the engine doesn't crank when you turn the key to start, But, the lights slowly come back on when you release the key. This is another classic: the bad battery connection. When you turn the key to start, the starter pulls so much current that it breaks the connection. Then, when you release the key, the connection slowly comes back. The connection provides enough power to turn the dash lights on, but not enough to crank the starter. Cleaning and tightening the battery terminals may fix this prob­lem.

Scenario: When you turn the key, you hear a single, hard clunk. Turn the headlights on and try again. Do the lights dim slightly when you turn the key? If so, you probably have a bad starter or a seized engine. If the headlights don't dim at all, or just barely dim, there may be a connection problem between the starter solenoid and the starter itself.

Scenario: When you turn the key, you hear a loud, scraping or grinding sound like metal on metal. The starter drive is bad, or the ring gear on the flywheel damaged, or both. You may get the starter to engage if you try turning the key a couple of times, but let go of the key right away if you hear the noise again. If the car does start, you should drive it right over to local repair shop and have the problem fixed.

Starting Problem #2: Engine Cranks but It Won't Start

Scenario: The engine seems to crank normally, but the engine doesn't even sound as if it's trying to start. Is there gas in the tank? Gas gauges are notoriously inaccurate. If you have to move your head to one side to get the needle to move off empty, try adding some gas to the tank.

Scenario: When you first turn the key on, you don't hear the fuel pump run. In cars with electronic fuel injection, you should hear a light hum a few seconds from around the fuel tank. That's the electric fuel pump running. If you don't hear the fuel pump run for a couple seconds when you first turn the key on, try cranking the engine until the oil light goes out. That may start the pump running and allow the engine to start.

Scenario: The engine cranks normally, and it sounds like it wants to start, but it won't. You may have flooded the engine. Hold the gas floor and try again. (Let the gas pedal up when it finally starts). If it's raining out, the ignition system may be wet.

Scenario: The engine cranks unevenly in a repetitive-sounding pattern. You may have a bad timing chain or timing belt. Call a tow truck and have it towed to the repair shop.


Starting Problem # 3: Engine Starts but It Shuts Off

Scenario: The engine starts right up, but shuts off as soon as you release the key. This is the classic symptom of a bad ignition switch. A new switch should fix it.

Scenario: The engine starts and runs, but when you put the transmission in gear, the car lurches and the engine shuts off. The converter clutch in the transmission torque converter probably is engaging when it shouldn't. On some cars, you can bypass this by disconnecting the torque converter clutch solenoid; but unless you know which wire to pull, forget about it. Call for assistance.

Scenario: The engine starts and runs, but seems to idle slowly and stalls when you come to a stop. This probably is a fast idle problem. When the engine is cold, it's supposed to idle a little faster than normal to keep the engine running. You may be able to drive using two feet until the engine warms up: one on the gas to hold the idle up a little and the other for the brake. However, don't keep driving it this way. Take your car to your repair shop just as soon as you

Not finding what you are looking for?

284 views

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...