Question about 1996 Ford Crown Victoria

1 Answer

Will 93 crown vic ,motor work in 96 crown vic

Wit ever thing off 93

Posted by on

Ad

1 Answer

No,not without a lot of switching of electronics

1993 is OBD1 & 1996 on is OBD2 System

The engine may be okey-- but not the induction
system or any electrical

Posted on Dec 25, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Cruise control on my 96

I dont know if they had it in 96 but there is something called a speed control deactivation switch. Maybe check your owners manual about that.

Posted on Aug 18, 2008

  • 5692 Answers

SOURCE: 94 crown vic driver power window does not work can

The window regulator can be broke. Its made of plastic and they break often.

Posted on May 05, 2009

  • 5692 Answers

SOURCE: Wiper motor replacement for a 99 crown vic

I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

Posted on May 06, 2009

  • 163 Answers

SOURCE: how to remove wiper arm 96 crown vic

WHERE THE WIPER ARM AND SHAFT COME TOGHER THERE IS A LEVER LIFT UP THE WIPER SO THAT IT IS POINTING AT THE SLY AND PRY OUT THE LOCK AT THE BASE OF THE WIPER ARM .

Posted on Sep 13, 2009

  • 108 Answers

SOURCE: 2005 Crown Vic climat contr fan not working Fuses good Motor good

does it have a digital control panel? As this uses an electronic blower speed controller located at the engine compartment (rear engine block) fix on ac phlenum try to shake the connector or wire while the system is on.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater in 2003 crown vic stays on always , can't shut down or control


Heater in 2003 crown vic stays on always ???? Blower motor ? Air blowing out vent's all the time ? Blower motor speed control module .maybe ! If that is what your taking about . Can't turn blower motor off .

Dec 14, 2017 | 2003 Ford Crown Victoria

1 Answer

Rebuilding motor 96 crown Vic


Buy a used factory repair manual so you know the info is accurate. You can find used factory manuals on eBay motors.

Jul 16, 2016 | 1996 Ford Crown Victoria

1 Answer

Modifying a 96 Crown Vic


Explain what CVPI stands for a start.

Jul 16, 2013 | 1996 Ford Crown Victoria

1 Answer

No high beams on my 96 crown vic. fuses good. any suggestions?


look under the hood in the big fuse panel and look for High beam headlight relay the relay is more than likely bad

Jun 17, 2009 | 1998 Ford Contour

1 Answer

Wipers will not park on 93 ford crown victoria


Hmmmm... if you replaced the motor you must have cleaned the area housing the arm mechanism. I had the same problem and found the problem to be in the arm assembly box on the firewall. Under the hood, triangular shaped box with snap on top was full of dirt, leaves and pine needles... I removed all the **** & my wipers now park as they should!!

Mar 14, 2009 | 1993 Ford Crown Victoria

1 Answer

Cruise control on my 96 Ford Crown Vic has stopped working. What should I check first?


I dont know if they had it in 96 but there is something called a speed control deactivation switch. Maybe check your owners manual about that.

Aug 05, 2008 | 2005 Ford Crown Victoria

1 Answer

Replacing the starter on a crown vic


I mount bolt is a RELLY hard to remove. Pay the money and have a mechanic do it on a lift.

Jun 18, 2008 | 1993 Ford Crown Victoria

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...