2002 Isuzu Trooper Logo

Related Topics:

Posted on Dec 18, 2012

4jx1 timming & flywheel setting

Hi i got my engine recondined & i can,t get it to start. someone said i have to set the fly wheel & the tdc of engine can any one help?

4 Related Answers

Anonymous

  • 3533 Answers
  • Posted on Mar 21, 2009

SOURCE: refitting new fly wheel

try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Ad
A

Anonymous

  • Posted on Aug 15, 2008

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

1125rguy

Bill Wilson

  • 40 Answers
  • Posted on Feb 04, 2011

SOURCE: hi i need the torque

torquespecs.com if not there there are several sites like that one that list any car u can dream of.good luck

Anonymous

  • 1 Answer
  • Posted on May 19, 2011

SOURCE: I am busy with an

timing marks

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
2answers

I have a 94 Hyundai Excel. I am replacing the clutch but can't find the torque settings anywhere.

clutch/flywheel torque settings - Hyundai Forums : Hyundai Forum

www.hyundai-forums.com/...accent/146383-clutch-flywheel-torque-setti...

Aug 2, 2012 - 3 posts - ‎2 authors
Im after the torque setting for the clutch and fly wheel for a lc 2000 accent with the dohc 16v engine. cheers.Missing: .94

Torque value head bolts 1994 hyundai excel 1.5l - Fixya

www.fixya.com/cars/t12339610-torque_value_head_bolts_1994_hyundai
Apr 7, 2012 - SOURCE: torque settings for a hyundai accent 1500 1998. cylinder ...SOURCE: how d i change a clutch in a hyundai excel 1994. Hi first lift the ...

Flywheel & Pressure Plate Torque Specifications? - Hyundai ...

www.hyundaiaftermarket.org > ... > Engine, Intake, Exhaust
0helpful
2answers

What is crank position sensor on Isuzu trooper 2002 3tdi

What is? It tells the ECU what position the crank is in to control timing.
0helpful
1answer

Isuzu trooper 2004 model 4jx1 engine what was the fly wheel marks if it was at tdc

if flywheel is fitted in correct position the timing mark on the front top cambelt gear is at 12 O clock and with starter motor removed you will see 3 lines stamped in the interuptor ring that is bolted to the rear of the flywheel if manual on early builds, also there is a notch in flywheel which you can see if gearbox is out this goes at 6 O clock
25312290-55d4lqh0wtq3cergg12nnjcv-3-0.jpg
0helpful
1answer

Isuzu trooper 2004 model 4jx1 engine where did was the fly wheel marks if it was at tdc

could be on the flywheel or the front pulley i just dont know where without a look myself but someone might know on here as and when they get time to answer questions
0helpful
1answer

How do I re- set correctly the fly wheel position on the crankshaft ?

go online to magicmechanic and send him the issue--hes a master on any make-model and will get back to you-------view his tech library or listen to his radio show--on saturdays call his shop for free advice
0helpful
1answer

Noise from motor flywheel

This is possible with engine off through a round inspection hole on transmission bell housing you can see the flywheel with a flashlight . now have someone rotate the engine by hand as you watch the flywheel a slight back and forth on rotation of engine can produce the noise and seeing the flywheel lag in rotation can prove the failure.
6helpful
3answers
1helpful
1answer

Need torque settings for dual mass flywheel in 3.0 isuzu trooper

diesel 4JX1 engine
apply engine oil to threads
1st- 59Nm(43lb ft)
2nd- 60-90deg.
3rd- 60-90deg.

8helpful
2answers

Fly wheel problem on a jeep

if its a 4JX1 diesel, yes it goes in 1 spot yet it can be bolted up in every location
put crank pulley timing mark to TDC can also check by removing cam belt top cover and check timing mark aligned up with mark at 12 O clock then flywheel has small notch in edge that must go at 6 O clock (facing down) look closely it is hard to see due to flywheel sunk into back of block.
2helpful
2answers

Isuzu trooper 3 litre diesell oo year!

with no1 at TDC mark is on balancer and can take off top cam belt cover to check that cam gear is timmed on mark at 12 O clock there is notch in edge of flywheel that should be put at 6 O clock (facing down) it is hard to see with flywheel on engine look closely
Not finding what you are looking for?

89 views

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...