Tire monitor how do you reset tire pressure monitor

Using the Driver Information Center (DIC)
Important: After resetting, the tire pressure monitoring (TPM) system requires up to 8 km/h (5 miles) of flat, smooth road straight line driving in each of the 4 speed ranges to complete the calibration process. For further information, refer to Tire Pressure Monitor Description and Operation . If the TPM system does not reset, refer to Driver Information Center (DIC) Switch Inoperative .

1. Set all tire pressures to the recommended kPa/psi. Refer to Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label .
2. Turn ON the ignition, with the engine OFF.
3. Press the vehicle information button until TIRE INFLATION MONITOR SYSTEM PRESS (down/left arrow) SWITCH TO RESET is displayed.
4. If the system is being reset due to a low tire pressure condition, press and hold the down/left arrow button until TIRE INFLATION MONITOR SYSTEM HAS BEEN RESET is displayed. If the system is being reset due to a tire rotation, press and hold the down/left arrow button for 5 seconds.
5. Release the down/left arrow button and TIRE PRESSURE NORMAL is displayed.

It's a sensor that goes off when your tire pressure is too low or too high. Check the air pressure.

Not sure what "exp 18" means...but the Low Tire Pressure or tire pressure monitoring on the Aurora is done via the wheel speed sensors. Anytime you fill or add air to the tire you will need to reset the tire pressure monitoring - not just the current indicator, but go to gage->tire pressure and reset.
If any of the wheel speed sensors are having issue, this can effect the reporting to the tire pressure monitoring. If you have an ODB-II scanner that can read ABS codes this is very helpful as it will tell you exactly which sensors are having problems.

Page 2-46 of your owners manual. If you don't have one you can get on online version from the chevrolet website. Just click the owners link at the top of the page.

TIRE MON (Tire Inflation Monitor Reset)
This feature allows you to reset the tire pressure monitor after checking all tire pressures. To clear the LOW TIRE PRESSURE light from the instrument panel cluster and reset the low tire pressure monitor do the following:

1. Scroll, using the SEEK/PSCAN up or down arrows, until TIRE MON appears on the display.
2. Press the PREV or NEXT button to enter the submenu. RESET will be displayed.
3. Press the TUNE/DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second.

The low tire pressure monitor is now reset.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

You shouldn't be setting the tire pressure to the max inflation pressure listed on the sidewall, that will likely result in uneven tire wear with the center of the tire wearing out prematurely. You should set the pressures according to the listings in the door jam. Most likely 32-34psi. Also, have you checked the spare tire? Some systems monitor and will illuminate the TPMS light if the spare tire pressure isn't within an acceptable range. The spare is often overlooked when checking tire pressures because of a TPMS indicator.

after you have inflated the tires to the correct pressure press the tire pressure button for a few seconds untill you hear a beep sound .that indicates the tire pressure has been reset. hope that helps

To reset the tire pressure light you need to get the tool.

You can get the tool here on link below.

http://cgi.ebay.com/ebaymotors/FORD-OEM-TIRE-PRESSURE-MONITOR-RESET-TOOL-TPMS-RESET_W0QQcmdZViewItemQQhashZitem45eed5e149QQitemZ300359737673QQptZMotorsQ5fAutomotiveQ5fTools

Your tire pressure monitor needs to be reset whenever you change or rotate your tires...

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

the last time I had a flat the tire pressure monitor came on a little too late. once the tire was replaced and brought up to pressure it reset itself. check your spare tire. have the tire that was repaired still has the module on the rim. they may have given you a different rim

make sure your spare is up to 32#'s pressure also , unless its one of the donut tires, turn ignition switch to on with engine off , press and hold GUAGE INFO button which is located to the left of the sterring column until TIRE PRESSURE messgage is displayed , press and hold RESET BUTTON for 5 seconds , TIRE PRESSURE RESET message should appear on display , release RESET button, a TIRE PRESSURE NORMAL message should appear on the display , after ressetting the Tire Pressure Monitor system it requires 30 minutes of straight driving to complete calibration process .

J5