Question about 1998 Oldsmobile Regency

1 Answer

Torque specs on wheel bearing retaining nut 1998 olds regency

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 20 Answers

107 ft-lbs is the correct torque specs

Posted on Dec 01, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: wheel nut

1"3/8"

Posted on Jan 15, 2009

  • 1 Answer

SOURCE: changing front wheel bearing

first take the wheel off
Then take the caliper off the rotor
Then take the rotor off the CV joint spindle
You will need to remove the three bolts that hold the bearing in place.
You will either need to remove the two bolts that hold the strut or
you will need a Puller.

Posted on Apr 01, 2009

  • 1168 Answers

SOURCE: I have a 1996 olds cierra. Need a torqe spec on

Hello Quiggle.
The axle nut torque is a 107 ft lbs according to the service manual.
Thank you for using FixYa !

Posted on Dec 03, 2009

  • 14092 Answers

SOURCE: front wheel bearing assembly unit, what tools will

TOOLS YOU NEED IS 35 METRIC SOCKET FOR AXLE NUT.USE 6 POINT SOCKET.DONT USE 12 POINT SOCKET.COULD DAMAGE AXLE BOLT EDGES.MAKING IT HARD TO GET OFF.YOU NEED A TORQUE WRENCH WITH THE RANGE OF 200 FT LBS TORQUE.YOU NEED 1/2 BREAK BAR.AND A HUB PULLER.NOW TO LOOSEN AXLE NUT.BEST TO LEAVE TIRE ON WITH CAR WEIGHT ON GROUND TO LOOSEN THE AXLE.BECAUSE ITS GOT 192 FT LBS TORQUE.HARD TO LOOSEN WITH TIRE OFF.192 FT LBS TORQUE IS WHAT YOU TORQUE IT AT.BESURE TO READ INSTRUCTIONS TO NEW HUB BEARING ASSEMBLY. YOUR AXLE NUT TORQUE WILL BE DIFFERENT IF YOU GET A NEW GREY NUT.BECAUSE NUT STRENGHT WILL BE DIFFERENT.IF YOU GET A BLACK NUT WHICH IS HARDER STEEL TORQUE WILL BE 192 FT LBS.YOU NEED A 13 METRIC SWIVEL SOCKET TO GET HUB BEARING BOLTS OFF THEY WILL BE IMPOSSIBLE TO REACH WITH OUT IT.HUB BEARING BOLTS TORQUE IS 62 FT LBS

Posted on Mar 17, 2010

  • 112 Answers

SOURCE: I just changed the front wheel bearing assemblies

96 foot lbs

Posted on Mar 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

97 F250 HD Rearend axle bearing retaining nut Torque Spec for used bearings. It is 10.25 sterling rear gear w/ 7.3L diesel eng.


Axle retaining nut torque spec is 55 to 60ft lbs. back off 5(new) or back off 8(used) clicks, and axle retaining bolts 60-80ft lbs in criss cross pattern.

Apr 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

Torque settings for rear wheel bearing, 1998 Escort 1.8 TDI Ghia


If you mean the rear spindle castle nut, tighten until wheel will not turn, then back off until it spins freely. The rear wheel hub retainer is 188-254 ft lbs or 255-345 Nm.

Feb 28, 2011 | 1998 Ford Escort

1 Answer

How does one tighten up front wheel bearings


There are several different methods depending on what type of vehicle you are working on. For example : A front wheel drive car will require knowing the torque specification and tightening the retaining nut to that spec. on most rear wheel drive vehicles you tighten the retaining nut untill there is no play in the bearing and then back off 1/4 turn to the first locking hole in the spindle and install the cottter pin to lock the nut in place. Thats the basic run down and if you need more in fo just ask here and I will help you out. Rich

Nov 19, 2010 | Toyota Land Cruiser Cars & Trucks

1 Answer

I am installing a spindle hub bearing assembly on the front wheel of a 1994 Buick Le Sabre. I need the torque spec. for the 3 retaining bolts and hub nut.


Well the torque for the three retaining bolts should be about 75-85 ft lbs.and the hub nut about 100 ft lbs.

Apr 22, 2010 | 1994 Buick LeSabre

2 Answers

What is the torque specs for the front wheel bearing/hub assembly nut on a 2002 ford mustang?


Wheel bearing don't have torque specs (to the best of my knowedge). They have a procedure - in this case it is....
1. With everything clean and packed with grease, snug the bearing lock nut until it stops.
2. Reverse it about 1/8th to 1/4 turn and insert the cotter pin.
Done

Oct 11, 2009 | 2002 Ford Mustang

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

Not finding what you are looking for?
1998 Oldsmobile Regency Logo

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Jonah Oneal

Level 3 Expert

14092 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...