Check the help link below and follow the procedure:----How to replace Brake Power Booster?
http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-brake-power-booster.html
---------Where is Power Brake Booster located on Car?
http://howtobyme.blogspot.com/2011/12/where-is-power-brake-booster-located-on.html
---------How to Replace Power Brake Booster on 1996
GMC Jimmy?
http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-power-brake-booster-on.html
---------
These will help.
Thanks.
SOURCE: Replacing rear brake light 2001 Jaguar S Type
They are just clipped in from the trunk. plastic tags.
JPTCAT
SOURCE: Installing a cd changer into a 2002 Jaguar S-Type
SOUNDS LIKE YOU HAVE A VERY EARLY MODEL CD CHANGER ALPINE UNIT THE S TYPE
USED A AUDIOVOX CD CHANGER HOPE THIS IS USEFUL
SOURCE: remove rear door panel on x type jaguar
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
SOURCE: removal of front right axle from a jaguar 2002 x-t...
Loosen the wheel hub nut.
Remove the front road wheel and tire.
Remove the tie rod end retaining nut.
Using the special tool 204-192 Ball joint Splitter
detach the tie rod end.
Remove the subframe reinforcement plate retaining bolts.
Loosen the subframe rear mount bolt.
Loosen the subframe front mount bolt.
Remove and discard the wheel hub nut.
using spcial tools 204-269Forcing Screw,205-491-01 adapter nuts,205-491 wheel hub puller
Detach the wheel knuckle.
Remove the lower arm ball joint retaining bolt.
Reposition the lower arm.
Detach the wheel knuckle.
using special tools 307-443 RH Halfshaft splitter ,307-442 RH Halfshaft splitter handle
detach the halfshaft.
Remove the exhaust muffler inlet pipe.
Remove the halfshaft seal.
Remove the transfer case Y bracket retaining bolt.
To prevent damage to the transfer box internal seal,
make sure that the link shaft is not retracted further than
200 mm from the transfer box casing.
remove the halfshaft.
Attach special tools to the halfshaft.
Lever the special tools to displace the halfshaft.
Install the transfer case Y bracket retaining bolt.
Remove the halfshaft.
Use suitable protective covers to protect the barshaft.
Remove the halfshaft snap ring.
Install a new snap ring to the halfshaft.
Install a new halfshaft seal.
Remove the special tool.
Remove the transfer case Y bracket retaining bolt.
Remove the special tool.
Make sure the CV joint splines are located fully.
Do not use excessive force when engaging the CV joint into the link shaft.
Install the halfshaft.
Install the transfer case Y bracket retaining bolt.
Tighten to 25 Nm.
Attach the wheel knuckle.
Reposition the lower arm.
Attach the wheel knuckle.
Install the lower arm ball joint retaining bolt.
Tighten to 83 Nm.
Install the exhaust muffler inlet pipe.
Tighten the subframe front mount retaining bolt.
Tighten to 142 Nm.
Loosely install the subframe rear mount retaining bolt.
Install the subframe reinforcement plate retaining bolts.
Tighten to 35 Nm. Tighten to 142 Nm.
Install the tie rod end.
Tighten to 35 Nm.
Loosely install a new wheel hub nut.
Install the front road wheel and tire.
Tighten the wheel hub nut.
Tighten to 330 Nm.
Check the subframe alignment.
528 views
Usually answered in minutes!
×