Which fuse controls the door locks?

Here are the codes you posted along with the possible issues that may have caused each code to be triggered. It's possible the circuit these switches share has a problem that needs to be diagnosed.

It could well be a problem with the wiring or a problem with the connections between the switches and the Multiplex Control Unit, or possibly with the Multiplex Control Unit itself.

B1129

• Driver Side Door Lock Knob Switch Signal Error
• Faulty Driver Side Door Lock Knob Switch
• Driver Side Door Lock Knob Switch harness is open or shorted
• Driver Side Door Lock Knob Switch circuit poor electrical connection
• Faulty Door Multiplex Control Unit

B2077

• Right Power Sliding Door Remote Control Switch 1 Signal Error
• Faulty Right Power Sliding Door Remote Control Switch 1
• Right Power Sliding Door Remote Control Switch 1 harness is open or shorted
• Right Power Sliding Door Remote Control Switch 1 circuit poor electrical connection
• Faulty Right Power Sliding Door Control Unit

B2078

• Right Power Sliding Door Remote Control Switch 2 Signal Error
• Faulty Right Power Sliding Door Remote Control Switch 2
• Right Power Sliding Door Remote Control Switch 2 harness is open or shorted
• Right Power Sliding Door Remote Control Switch 2 circuit poor electrical connection Faulty Right Power Sliding Door Control Unit

B2079

• Right Power Sliding Door Remote Control Switch 3 Signal Error
• Faulty Right Power Sliding Door Remote Control Switch 3
• Right Power Sliding Door Remote Control Switch 3 harness is open or shorted
• Right Power Sliding Door Remote Control Switch 3 circuit poor electrical connection
• Faulty Right Power Sliding Door Control Unit

Here is how it works !
Liftgate Locking Operation
The lift gate will lock any time the vehicle is shifted out of park on vehicles equipped with an automatic transmission and at vehicle speeds exceeding 5 kph with manual transmission. This happens in conjunction with auto door locks if enabled or independently of auto door locks if the feature is disabled. This ensures that the lift gate is locked anytime the vehicle is shifted out of park or when the vehicle is in motion.
The lift gate lock relay supply and coil sides receive a constant voltage through the battery voltage supply circuit and the ECC fuse. The normally closed contact is connected to ground and the control side is connected to the body control module (BCM). A lock function will occur when a door lock switch activation, keyless entry lock transmission, auto door lock function or a lift gate lock function has been received by the BCM. The BCM will then ground the control side of the lift gate lock relay. This energizes the relay and allows voltage to be applied to the lift gate lock actuator lock control circuit. Since the other side of the lift gate lock actuator is connected to the normally closed contacts of the door unlock relay to ground, the lift gate will lock. When an unlock function occurs the BCM will ground the control side of the unlock relay and the rear doors and lift gate will unlock.
The BCM also runs diagnostics on the lift gate lock relay control circuit and will set DTC B3825 as current and also send a Class 2 message to the DIC. The DIC will display REPLACE LIFTGATE FUSE to inform the driver that a fault has been detected in the lift gate lock circuit and that the lift gate is not locked. Faults that will set the DTC and cause the DIC to display the message could be any of the following:
?€¢
An open ECC fuse

?€¢
An open or short to ground in the lift gate lock relay battery positive voltage circuit

?€¢
A faulty lift gate lock relay

?€¢
An open or short to ground in the lift gate lock relay control circuit

?€¢
A short to ground in the lift gate lock actuator lock control circuit

?€¢
A faulty BCM

Key switch ? key fob ? Transmitter Programming ?
If you lose a transmitter, program the old and new transmitter(s) into the remote control door lock receiver's memory. Up to 4 transmitters may be programmed.
Important: Once the remote control door lock receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information, requiring the programming of all transmitters.
Program only 1 vehicle remote control door lock receiver at a time. If more than 1 receiver is being programmed at the same time, it is possible that the same transmitter could be programmed to more than 1 remote control door lock receiver.
Perform the following steps in order to program the transmitter:

1. Remove the ignition key from the ignition lock cylinder.
2. Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.
3. Close all of the doors.
4. Close the lift gate.
5. Turn the ignition lock cylinder to ACC.
6. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
7. Open and close any vehicle door.
A chime will be heard when the system enters the BCM programming/diagnostic mode.
Important: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.

8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
9. Repeat the previous step on each additional transmitter to be programmed.
10. Remove the ignition key from the ignition lock cylinder.
11. Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems.

rear door hatch lock repair GMC Chevrolet - YouTube

? 4:26
https://www.youtube.com/watch?v=QS3PMhGgyAg
Apr 5, 2014 - Uploaded by auto resource
2002 Yukon, rear hatch lock not locking. ... rear door hatch lock repair GMC Chevrolet. auto resource ... chevy tahoe lift gate notopening - Duration: 2:12. ... A Method how to unlock your car in 10 seconds :) - Duration: 0:35.

chevy tahoe lift gate not opening - YouTube

? 2:12
https://www.youtube.com/watch?v=xU6ybiY3F4I
Sep 1, 2010 - Uploaded by 76bluemoon
Back lift gate/glass would not open or release. Even when unlocked with the key fob or the unlock switch on the drivers/passenger door. ... How To Install Replace Rear Lift Gate handle 2002-09 GMC Envoy Chevy Trailblazer ...

Central lock problem, rear door and trunk don´t open - Xoutpost.com

www.xoutpost.com > ... > BMW SAV Forums > X5 (E53) Forum

Aug 23, 2014 - 10 posts - ‎4 authors
I have a problem on my X5, the remote key can only open the front ... I´m in a distante country without any BMW representative, but I can ... Remote keys can only lock andunlock the front doors, the rear door locks does not respond. .... the front doors openit won't unlock or lock the rear doors and rear trunk. Door Won't Lock With Key
10 posts
Sep 26, 2013
Door Lock (passenger side) won't unlock with remote
10 posts
Jan 10, 2011
Upper Tailgate wont open from the outside
8 posts
Sep 2, 2009
More results from www.xoutpost.com

X5 Tailgate Diagnosis E53 - YouTube

? 3:12
https://www.youtube.com/watch?v=ZqBfkJzUQug
Nov 7, 2011 - Uploaded by AskTheCarExperts
Lower tailgate diagnosis including relay location and fuse location. ... BMW 3 Series E90 Car Key Memory and ...

BMW Electric Boot Release Fix - YouTube

? 10:02
https://www.youtube.com/watch?v=snOVnM7hyO4
Jan 23, 2011 - Uploaded by Cpt MishMash VonRandom
Thanks**This is a quick walk through to repair the boot or trunk release button on y. ... or other BMW of the ...

BMW X5 xDrive 30i automatic tailgate does not w

There are actually three relays , an there are controlled by the BCM - body control module !
When a door lock switch is activated in the lock or unlock position the BCM will receive a voltage signal on either the door lock switch lock or unlock signal circuits.
The BCM, upon receipt of a lock switch lock or unlock signal, will switch the appropriate lock relay control circuits to battery positive voltage. This will energize the appropriate lock or unlock relays. The relay will supply voltage to the door lock actuator lock or unlock control circuits to one side of the lock actuator. Since the opposing side of the lock actuators are connected to ground through the other lock actuator control circuit and the normally closed contacts of the lock or unlock relay, the doors and liftgate will then lock or unlock appropriately.
Three relays are used to operate the locks. DRV DR UNLCK relay, PASS DR UNLOCK and DR LCK relay. This is done to isolate the driver door lock actuator so it can be unlocked by itself using the keyless entry transmitter.
Rear Hatch/Gate Description and Operation
The liftgate can be opened by operating the switch on the instrument panel. Battery voltage is supplied to the liftgate actuator through the body control module (BCM). The BCM will pulse the liftgate actuator when a release input is received through the key fob, or the instrument panel switch.
Door/Lift gate Latch Assembly

1. Install a 20-A fused jumper wire between the control terminal 3 and 12 volts. Install a jumper wire between the ground terminal 2 and ground.
2. Verify the actuator turns on & off.

?‡'
If the function does not perform as specified, replace the applicable door latch.

IMPREZA: 2005, 2006, 2007 and
FORESTER: 2005, 2006, 2007, 2008
Check for Immobilizer key on Forester XT models only.
information is always subject to change and correction
new remote for 2005 Imprezas.
This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
Programming: 4 codes may be programmed.
Sit in driver's seat and unlock all doors. Open and close the driver's door
Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
You now have 45 seconds to complete the programming as below.
Open and close driver's door again.
Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
Done programming? remove the key from the ignition and the horn will honk 3 times.
DELETE old codes? Reprogram 4 times, it will overwrite old codes.
Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
Disarm the system: push unlock for 2 seconds
Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
Identification mode: To find out what happened and why the system was triggered:
Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

Actually I found a solution. I remove the lock relay form the fuse panel and placed it back in place. I did not replace it. After doing this they worked. I probably need to replace the relay at some point, but for now that solved the problem. It was hard for me to believe that there is a separate relay for the lock and unlock circuit.

SYSTEM OPERATION

System warning lamp located on top of the instrument panel
Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted)
Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted)
To activate alarm system (if fitted):
Switch ignition OFF
Open driver's door
Press Lock button on remote
Close Driver door
warning lamp will flash when system is activated
Press remote power sliding door button will open sliding door (if fitted) only if unlocked first
Pressing remote panic button:
*Sounds horn intermittently
*Flashes exterior lamps
*Turns on interior lamps
**Pressing panic for the second time OR switching ignition ON deactivates alarm.


PROGRAMMING
Remobe key from ignition switch
Remove the "BCM PRGRM" fuse, from the fuse box
Close all doors
Turn ignition switch to the ACC position
With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC'
(really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated
Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds)
Repeat this exact procedure for all remotes to be programmed
Remove key from ignition
Refit 'BCM PRGRM' fuse.

4 REMOTES MAXIMUM CAN BE PROGRAMMED

1) Unlock all doors from driver's door while it is open. The driver's door is the only door to remain open during this process! 2) Turn the key from OFF to RUN 8 times within 10 seconds, with the eighth turn ending in RUN. All the doors will lock and unlock if program is successful. 3) Turn key OFF and remove key from ignition. Within 20 seconds, press any button on the remote. (Press sliding door or rear hatch and it will open!) 4) If door locks do not respond, wait several seconds and press button again. If doors still fail to respond, try repeating steps (1-3).