Question about 2004 Chrysler Pacifica

1 Answer

Keys locked in Chrysler Pacifica 2004

My husband locked both sets of keys in the car. One is in cup holder, other in ignition. Any ideas how the heck to get a door unlocked?? Framed doors, no windows cracked, any ideas?

Posted by on

  • 1 more comment 
  • dealsbyjuju
    dealsbyjuju Nov 28, 2012

    I called the local dealership & they will make you a key for $10, since the Pacifia has the computer keys, but you have to have your title or registration; which was locked in car.

  • dealsbyjuju
    dealsbyjuju Nov 28, 2012

    We didn't need to do that, he had a long metal ruler thingy and got the door open an inch and tried to hit the unlock button, but because the door was pried open it wouldn't work. So he put a small bungy w/ a hook on the ruler and hooked the keys out that way.

  • micah mardo
    micah mardo Feb 26, 2014

    a slim jim doesn't help..the best way is to shimmy the door as much as possible and use a long pole to push the actual lock button, not the electric one..Learned this the hard way..

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Filmmaker:

    Uploaded 5 video answers.

  • Expert
  • 98 Answers

Do you have USAA insurance? I believe they have roadside assistance included in your policy which may include unlocking the door. Try calling your insurance carrier either way and find out if a locksmith is covered. On these newer vehicles I'm not sure if the old school slim jim works to unlock them.

Posted on Nov 23, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
turo1000
  • 18 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Posted on May 18, 2009

  • 1779 Answers

SOURCE: car won't crank & makes a clicking noise when ignition is turned.

Is this the original battery? Have u had it tested? The no crank, clicking noise is classic dead battery symptoms, lights can still work, but not enough power to turn engine over. If it's the original battery, it's at the end of it's life cycle, and should be replaced. U can get the battery tested for free at any parts store.

Posted on Dec 30, 2008

ga_drifter
  • 36 Answers

SOURCE: 2004 chrysler sebring.The driver side rear door electric window

you have a bad window regulator assembly

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: car door unlock and lock by itself

door fuse massage comes up

Posted on Apr 18, 2009

  • 12 Answers

SOURCE: Back door wont unlock

I have a 1999 Chrysler T&C 3.8 liter like yours and it sounds
like you are having the same the same problem I had.
Every time you hit the door unlock or lock button, it made a loud
buzz like you just missed a question on a game show. ;-)

It turned out the problem was the rear lift gate lock actuator. The part costs
about $40 from the dealer if I can recall correctly.

The repair involves: 1st removing the middle and rear seats to get
access from the inside to the rear gate
(obviously you will have to remove the seats from the side doors
since the rear gate won't open yet)

Remove the plastic inside rear gate panel and molding (phillips screws)
Once you remove the panel, you may see a way to manually
open the rear gate. As I recall, I think there was a access opening
covered from the inside with a black weather/insulation tape.
Carefully removing this out of the way gave access to a way to
manually open the gate, making the rest of the work easy.

Remove the electrical connector and the mounting bolts
to remove from the actuator. It is attached to the inside
rear gate with 2 or 3 bolts (10 mm?)

Remove the old one and replace the part, then put it all back
together, make sure you reconnect the electrical connector

Takes about an hour for the whole job (max)

Hope this helps,

Wes

Posted on May 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Doors will not open with the key that I have for the ignition. Any ideas?


Auto Repair : Power Door Lock Troubleshooting

sofia2013.com/auto-repair-power-door-lock-troubleshooting/
Jul 29, 2014 - can't use the key i have to go through the passenger door and unlock it ... when I get out of my 2003 Honda Accord, and leave the keys in the ignition, ... Any ideas why all the doors wont lock even pushing the lock button in the

Remote won't unlock passenger or rear doors - TDIClub Forums

https://forums.tdiclub.com/showthread.php?t=355194
Jun 4, 2014 - Will unlock the drivers side door and rear hatch (wagon). ... Any ideas, ... I have the VCDS and tried to program the remote with no success. ... precisely, but it was something like put the key in ignition, turn to acc, then push the unlock button. .... fiddling around with passenger door did not produce any result.

Door locked with key in ignition - TDIClub Forums

https://forums.tdiclub.com/showthread.php?t=125387
Dec 17, 2005 - Anybody have any ideas on this? I know there should ... The door willlock with the key in the ignition and the car running. It does automatically ...

Ignition key won't open door - 8th Generation Honda Civic Forum

www.8thcivic.com > ... > Mechanical Problems & Technical Chat

Dec 20, 2015 | Cars & Trucks

3 Answers

On my 04 rendezvus the power locks all doors will lock but only the driver door works on the unlook


Unlock usually takes 2 clicks to unlock other doors, if not you will need unlock relay

Apr 05, 2015 | 2004 Buick Rendezvous

1 Answer

An 08 prius keyless entry doesn't work, changed the batteries, pushed the disable button and reset it, still no go. Any ideas?


1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Perform these steps within 5 seconds.
A. Insert the key into the ignition and Pull key out twice (Do NOT Turn)


3. Perform these steps within 40 seconds.
A. Close then open the drivers door twice.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
A. Close then open the drivers door twice.
B. Insert the key into ignition and leave it in ignition.
C. Close the drivers door.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.

Jul 17, 2014 | 2008 Toyota Prius

2 Answers

I used csorb's instructions to reprogram a master key for my 2000 Lexus RX300. The ignition works perfectly, but the doors don't lock or unlock.


Hi!!
I believe your alarm is in the PASSIVE MODE, here is how it works.

PASSIVE MODE Setting (Arming) Anti-Theft System The system will automatically set 30 seconds after following methods are performed: Remove ignition key from ignition switch. Exit vehicle, and close all doors. After performing this, anti-theft indicator on left side of instrument panel will light continuously for about 30 seconds. After 30 seconds, anti-theft indicator will blink once per second. When system is set, doors cannot be locked or unlocked using door lock control switch.
CANCELING THE ALARM AND REPROGRAMING MAY SOLVE YOUR PROBLEM.
Canceling Anti-Theft System Setting (No Alarm) When system is set (armed), but alarm is not sounding, use one of following methods to cancel system setting:
  • Unlock left or right front door using key.
  • Unlock all doors using remote keyless entry system.
  • Insert key in ignition switch and turn to ON position (this is operative only when anti-theft system has not been triggered).
HERE IS HOW TO REPROGRAM THE ALARM IN CASE YOU NEED TO RESET IT.
PROGRAMMING
PASSIVE MODE NOTE:Initial mode is passive mode off. If there is a different signal in middle of programming, signal is invalid.
Programming Passive Mode Off
  • Remove ignition key from ignition key cylinder. Ensure all doors (including back door) and engine hood are closed and unlocked. Perform all of following methods within 30 seconds:
  • Lock or unlock any door with key or remote keyless entry system.
  • Open driver door.
  • Lock and unlock driver door lock knob 3 times.
  • After performing this, system should start force lock after 2 seconds. Perform all of following methods within 20 seconds:
  • Unlock driver door lock knob.
  • Close and open driver door 2 times.
  • Lock and unlock driver door lock knob.
  • After performing this, system should start force lock after 2 seconds. Passive mode should now be off.
Programming Passive Mode On
  • Remove ignition key from key cylinder. Ensure all doors, engine hood and luggage compartment door are closed and unlocked. Perform all of following methods within 30 seconds:
  • Lock or unlock any door with key or remote keyless entry system.
  • Open driver door.
  • Lock and unlock driver door lock knob 3 times.
  • After performing this, system should start force lock after 2 seconds. Perform all of following methods within 20 seconds:
  • Unlock driver door lock knob.
  • Close and open driver door 4 times.
  • Lock and unlock driver door lock knob.
  • After performing this, system should start force lock after 2 seconds. Passive mode should now be on.
If you need further assistance, please provide an email address to send more info on your security system
Good Luck!! A 4 THUMBS UP rating would be greatly appreciated for this solution. Thank you for using FixYa!!

Mar 01, 2011 | Lexus RX 300 Cars & Trucks

1 Answer

Neither of our remotes would unlock our doors on our 2003 Silverado Z71 the other day. So we tried by unlocking it with the key. That did'nt work either. Finally, we put the key in the lock and waited for...


TRY Relearning the remotes. to do this get in vehicle with doors closed hold the unlock button down on drivers door while you cut key on and off two or three times you should hear locks cycle and horn chirp. let go of unlock button and hold both lock and unlock button down on one key fob for 15 seconds or so you will see locks cycle move to next remote and do same. then cut key on to exit learn mode. as far as door not unlocking with key this is a problem with lock cylinder most likely.

Feb 16, 2010 | 2003 Chevrolet Silverado 1500

1 Answer

I have a 2004 Honda Accord EX. Key Fob works trunk but not doors


Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys. A maximum of 3 keys can be programmed. Close all doors and boot/tailgate. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press key lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press key lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press key lock or unlock button. Within 10 seconds: Press lock or unlock button of first key. System should now lock or unlock vehicle. Press lock or unlock button of second key. System should now lock or unlock vehicle. Press lock or unlock button of third key. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed keys.
NOTE: If less than 3 keys are to be programmed, remove ignition key after programming last key.

Jan 25, 2010 | 2004 Honda Accord

1 Answer

1998 Oldsmobile aurora first my key would turn very roughly or hard then the key got stuck my husband got it out and now when we put the key in it wont even turn the ignition. Can anyone help please?


If the duplicate key is still with you, you can give it a try. If it works, cool! Else the entire lock assembly for the ignition will have to be replaced only if your other key works in unlocking the remaining locks of boot, doors, fuel cap, etc. Otherwise the entire SET has to be replaced by a trained technician only...............sodeep

Jul 27, 2009 | 1998 Oldsmobile Aurora

1 Answer

For dgnoid: Car is 2002 Buick Regal. Husband is blind and I thought it would be cool for him to have remote key to lock and unlock car more easily, unfortunately, it did not come with instructions on how...


IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Once you program the remotes , all previous codes will be erased from the memory. The other remotes will not be functional until you program the remotes again.
1. Close the vehicle doors.
2. Insert key in ignition and turn to ON (As far as you can without cranking engine)
3. Turn ignition OFF and remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key.
| (Do not turn the ignition key in the lock cylinder.)


6.
Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder.)


7.
Insert the ignition key into the ignition lock cylinder. (Do not turn the
ignition key in the lock cylinder.) Leave the ignition key in the ignition lock
cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order to
verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless entry
transmitter and hold until the vehicle beeps twice to verify that the
transmitter has been successfully programmed (this take approximately 15
seconds).

10. Perform the previous step to program up to four transmitters (including your
old ones).

11. Remove the ignition key in order to exit the Program Mode.


Jun 29, 2009 | 2002 Buick Regal

2 Answers

Central locking not working on key.


Before you spend bigger amount, check the battery in the key. Usually a CR2032 battery can be find there. (Open the Keyfob by inserting an object into the key ring holder and pulling the top and bottom apart, Seperate the two halfs, Open the top half to expose the battery... )

Nov 28, 2008 | 1998 Audi A6

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

2,226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...