Replace struts how do i replace front struts

go google and type in-- front struts on honda accord 1999 model --and there is a video on youtube .com that shows you how to do ti

Go to u tube and Type in strut replacement on your bmw and watch a couple of videos and you can rent tools at car quest , auto zone , and Advance auto parts if you need ? I hope this helps out

Most new struts come with diagram you can purchase just the strut or the complete assembly. Recommend complete assembly and replace both sides and have an front end alignment done after installation. If doing your self use caution with compression tool. This tool can also be rented at auto parts store.

I have 06 daytona with same problem clunking noise front passinger side Master Mechanic's checked steering and suspension components could not find the source. Problem is that sometimes noise stops then comes back. I will try to find the source myself tomorrow let you know what I find.

Check your strut mounts, and front struts, my 2004 cadillac deville did the same thing between 67 and 75mph and after time it shook between 58 to 80mph, and it was the front strut mounts were egged out, and front struts were weak. I had my tires balanced, wheel bearings replaced, and it didnt help.

One needs a special tool called a 'spring compressor' to compress the front strut spring enough to remove the nut on the strut. Very dangerous without the tool. Must use the spring compressor to service the strut assembly, or get a loaded strut/spring assembly to replace old strut assembly.

Good luck on this.

The struts model (MacPherson Strut),are both in front and back of this car.
2000 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Rear, Driver Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly. $72
2000 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Rear, Passenger Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $68
1996 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Front, Driver Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $67
1996 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Front, Passenger Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $63
Of course this is only the cartridge, you have to transfer the spring, and the top mount of the existing strut. You need a pair of coil spring compressor to do the job. The basic procedure to replace a strut is:
Remove the top nuts that secure the strut assembly to the frame mount inside the engine compartment. Do not remove the center nut.
Mark the lower strut mounting location on the hub for installation reference. The alignment will be close if the new strut is installed in the same position.
Remove the bolts that hold the strut assembly to the hub.
Remove the strut assembly from the vehicle.
Mark the top mount for installation reference. Using a side mounted spring compressor, compress the spring and remove the top nut and retaining washer. Pull strut assembly out from the bottom of spring.
Slide the new strut assembly up into the spring and reposition the top mount onto the spring in the same position that it was removed. Install the retaining washer and top nut.
Tighten the top nut to the manufacturer's specifications and carefully remove the spring compressor.
Place the strut assembly back into the vehicle.

they need replacing , when doing so change both sides

Okay....here is the steps first....and then the directions on how to use the tools:

1. Raise and properly support the vehicle.
2. Remove the front wheel.
3. Detach the shock absorber lower mount by removing the two bolts.
4. Remove the retainer nut, retainer, cushion and shock absorber.
5. Detach the cushion retainer from the shock absorber.
6. Compress the coil spring with a commercially available spring compressor.
7. Detach the stabilizer bar.
8. Support the upper suspension arm and steering knuckle securely.
9. Remove the cotter pin.
10. Loosen and remove the nut.
11. Using a ball joint removal tool, detach the lower ball joint from the lower control arm.
12. Loosen the suspension arm set bolt.
13. Remove the suspension arm set bolt nut.
14. Remove the nut from the strut bar front set bolt.
15. Pull out both set bolts.
16. Remove the lower suspension arm and coil spring. To install:
    
17. Installation is the reverse of removal. Note the following torque specifications:
    1. Strut bar front set bolt: 221 ft. lbs. (300 Nm)
    2. Lower suspension arm set bolt: 148 ft. lbs. (200 Nm)
    3. Lower ball joint nut: 80 ft. lbs. (110 Nm)
    4. Lug nuts: 83 ft. lbs. (110 Nm).