Question about 2009 Hyundai i30 1.6

3 Answers

Cant find jacking points - 2009 Hyundai i30 1.6

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 22 Answers

If you can find the jack there should be a picture on it, one spot is usually behind the front wheels just inside the sill(pinch weld), its like a double layer of steel(reinforced).

Posted on Nov 10, 2012

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 56 Answers

Determine the jack type. Frame jacks and body jacks lift differently.

Posted on Sep 03, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 14,092 Answers

Look in owner manual for jacking points.

Posted on Nov 11, 2012

×

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is a safe trolley jacking point on the front end of a peugeot partner


THE ONLY SAFE WAY IS TO JACK ON THE FRONT CROSS MEMBER,AND PLACE TRESSELS ON THE CHASSIS(SAFETY FIRST)

Jan 04, 2013 | Peugeot Partner Cars & Trucks

1 Answer

Where are the jack points on a 1987 VW golf?


The jack points are in the sill joints under the car and are marked by wedge shaped indicators. THe jack for the car has a groove that the reinforced jack points fit into. The original jack is a Y type but an ordinary scissor jack with the correct groove in the lift point would also work. Attempting to lift the vehicle at any other point may cause damage to the underside of the car.

May 05, 2011 | 1987 Volkswagen Golf

1 Answer

Hi all how do i use the jack of a 1997 318i bmw on the back wheel that is flat


Hi, BMW's have a jacking point. If you are looking at the back wheel, look along the side skirts under the back passenger door. There will be a small disc with a horizontal hole. Use a screw driver to turn the disc until it comes out, that is your jacking point.

Place the jack's horizontal arm all the way into the jacking point and start to wind the jack handle. The car will then start to rise at the back. The same prinicple appplies for the front as well, the fronts jacking point is on the skirting under the front doors.

Jan 10, 2011 | BMW 318 Cars & Trucks

1 Answer

I cant find where to put the jack!


to hoist your car with the factory jack, there are small hole covers below the doors for front and back, {4} pry the plastic cover about 2.5" in diameter, this will expose the strongest points to place the jacks prop shaft. good luck

Dec 18, 2009 | 1997 BMW 318

2 Answers

Lift points on chassis for a floor jack


I use exactly the same the jacking points as I would use with the factory scissor jack. They are reinforced to handle the load. You'll find these point marked with triangle stamped into the rail and in your owner's manual.

Dec 14, 2009 | 2008 Saturn Aura

1 Answer

The function that rsiaes and lowers the vehicle doesn't work,


Lifting

The following instructions must be carried out before raising the vehicle off the ground.

  • Use a solid level ground surface.
  • Apply hand brake.
  • Select 'P' on automatic gearbox selector.
Note: If the propeller shafts are to be removed, reference must be made to the relevant operation. To avoid damage occurring to the under body components of the vehicle the following jacking procedures must be adhered to.

DO NOT POSITION JACKS OR AXLE STANDS UNDER THE FOLLOWING COMPONENTS:
  • Body structure other than approved jacking points
  • Bumpers
  • Fuel lines
  • Fuel tank
  • Brake lines
  • Front or rear suspension arms
  • Transfer box
  • Steering linkage
  • Front or rear differential units
  • Engine sump
  • Automatic gearbox
NOTE: For certain repair operations, it may be necessary to support the engine under the sump. In this case, a block of hardwood or a rubber block should be positioned on the jack lifting cup to protect sump. Vehicle jack
The jack provided with the vehicle is only intended for use in an emergency, for changing a tyre. DO NOT use the jack for any other purpose. Refer to Owner's Handbook for vehicle jack location points and procedure. Never work under a vehicle supported solely by the vehicle jack.

Hydraulic jack
A hydraulic jack with a minimum 1500 kg, (3,300 lbs) load capacity must be used.

WARNING: Do not commence work on the underside of the vehicle until suitable axle stands have been placed in their correct position. Always chock the wheels when jacking. The handbrake may be ineffective when the wheels are off the ground. Raising and supporting the vehicle
To assist in raising the vehicle, jacking points are provided as shown in the following illustrations.

Raising the front of the vehicle
Apply handbrake, select 'P' on automatic gearbox selector and chock rear wheels.
Axle stand positions - front

Raise vehicle to enable axle stands to be positioned under, either, the front sub-frame, or the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.
Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack.
Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Raising the rear of the vehicle
Select 'P' on automatic gearbox selector and chock front wheels.

WARNING: Always chock the front wheels when jacking the rear of the vehicle.

Axle stand positions - rear

Raise rear of vehicle to enable axle stands to be positioned under the rear sub-frame. Alternatively, the axle stands may be positioned under, either, the recommended customer jacking points or the front mounting points of the rear sub-frame.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If any damage occurs to the washers on the front mounting points of the rear sub-frame, then the washers must be replaced. Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack. Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Wheel-free lift
The following warning must be read before attempting to lift the vehicle.

WARNING: The vehicle cannot be supported safely in a wheel-free condition using the wheel-free facility of a four post ramp, and under no circumstances must this method be employedA wheel free condition may only be achieved on a four post ramp by raising each end of the vehicle and positioning axle stands beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox. WARNING: The front and rear suspension lower arms must NOT be used as lifting / jacking points. Alternatively, support the vehicle on an approved two post lift with the arms of the lift beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between the lifting equipment and the jacking points to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.

Oct 04, 2009 | 2003 Land Rover Range Rover

1 Answer

2004 tiburon : front jacking points?


The official front jacking points are on the reinforced edge of the unit body, just behind the front wheels.

If you're using a hydraulic jack, you can jack the front of the car from the front tow hook, place your axle stands under the front jack points, then let the car down onto the axle stands.

Always use axle stands when working on your car, never trust the jack alone.

Jul 05, 2009 | 2004 Hyundai Tiburon

1 Answer

Hi my front offside suspention spring has cracked an i need too know how to remove it thanx . its for a renault 19 16v 1995 model


I have a renault 19 with the same problem on the passenger side front. It is a straight forward job, you will need two jacks, preferably trolley jacks. It would be alot easier (and cheaper) to completely replace the suspension strut itself rather than squeezing a new spring in. Jack up the car then jack the suspension to a point it will hold suspension in place whilst you undo the bolts etc. Once bolts are undone, SLOWLY release the jack on the actual suspension strut and remove the strut. To replace the strut, put new strut in place jack it up into place carefully so you get it to stay in place. Do up all your bolts, Slowly release jack on suspension strut, then release the other jack holding up the car. I would do this with my car, but i cant be bothered as it has numerous other problems and im scrapping it.

Mar 11, 2009 | 1986 Renault Sport

1 Answer

Where are the jacking points on the hyundi accent


http://econtent.autozone.com:24991/znetrgs/repair_guide_content/en_us/images//0900c152/80/07/33/62//medium/0900c15280073362.gif

this shows jacking points.

Sep 24, 2008 | 1997 Hyundai Accent

Not finding what you are looking for?
2009 Hyundai i30 1.6 Logo

Related Topics:

1,236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...