I need to know how to replace a heater core in 1996 jeep grand cherokee loredo

SOURCE: 2000 jeep grand cherokee v8/heater core

Yes it's the heater core, It's a complicated diy job and unless you are an experienced mechanic you are going to need a good workshop manual for the job.

Best of luck.





Please remember to rate this article

SOURCE: how do i replace the heater core on a 1996 Grand

REMOVAL AND INSTALLATION

Note: This revised Heater A/C Housing service procedure is referenced from Technical Service Bulletin No: 24-02-98. Removal

1. Disconnect battery. This must be done to prevent accidental airbag deployment.
2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
3. Remove the shift knob by pulling sharply upward.
4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
10. Remove the "A" post trim panels.
11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
12. Disconnect the park lamp switch.
13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
18. Unplug the antenna cable near the right cowl side panel.
19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
20. Remove the bolts that secure the instrument panel armature to the windshield fence.
21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
29. Remove the coolant overflow bottle.
30. Remove the Powertrain Control Module with connectors intact and set aside.
31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
32. Remove the heater A/C housing from the vehicle.
33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Testimonial: "Excellent!!! Thank you very much."

SOURCE: Heater Core replacement

yes you do have to disconect the a/c system.google dash removal for jeep.hope this helps

ZJ Limited

• 17989 Answers
• Posted on Nov 12, 2009

SOURCE: heater core

You need review details in the Service Section-24-Heating-Air-Conditioning and Section-24a-Heating-Air-Conditioning

Hope helped with this (remember rated this help). Good luck.

SOURCE: 1996 jeep grand cherokee blower works but no heat

Since your blower is working and it is a heat issue,thats where we'll start,First thing is have you checked the coolant level in the radiator when engine is cold,make sure it is filled to top,next verify you have coolant in reserve ,Start your van and get it up to normal operation temperature,If your heat gauge on the dash works correctly it should be 190 degrees,Now lift the hood and locate the two heater hoses going into the heater assembly at the fire wall,Both hoses should be hot to hold on to,if both are hot and no heat inside your problem will be the blend air door in heater assembly.
if neither hose is that hot you need to replace the thermostat in the engine to get it up to 195 degrees.
if one hose is hot and one is luke warm then the heater core is blocked and to blame. hope this helps you.

Testimonial: "Thanks!!!"