Where is the blend door actuator located on 2006 Chevy Silverado?

1996 Chevrolet K1500 Air Blend Door Actuator

Advance Auto Parts https://shop.advanceautoparts.com > ... > AC Actuators
This air door actuator directly replaces the original actuator on specific vehicle years, makes, models, configurations and positions to restore proper HVAC ...

Blend door actuator

GMT400 https://www.gmt400.com > threads > blend-door-actua...
May 3, 2021 - The blend door is in the middle of the dash and mounted on the coil box. The one by the blower controls the damper that directs air intake from ...

VCAUTO HVAC Blend Door Actuator for 1996-2013 ...

Amazon.com https://www.amazon.com > VCAUTO-Actuator-1996-...
VCAUTO HVAC Blend Door Actuator for 1996-2013 Chevrolet Express 1500 2500 3500; 1996-2013 GMC Savana 1500 2500 3500; 1996-2013 Cadillac DeVille 604-125.

They are usually behind the centre console and glove box

https://www.google.com/search?q=2006+Chevy+HHR+6%2C+2.4L.+replace+the+blend+door+actuator

..

Temperature Blend Door Actuator - RH, EATC Removal and Installation

1. Remove the RH floor console finish panel.

1. Lower the glove compartment.

1. Disconnect the RH temperature blend door actuator electrical connector.
2. Remove the 3 RH temperature blend door actuator screws.
1. Remove the RH temperature blend door actuator.

2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

faulty actuator
Blend Door Actuator Replacement 1999 2007 Chevrolet Silverado

How To Install Replace AC Heater Temperature Actuator ...

? 4:40
https://www.youtube.com/watch?v=mVP09M7hLB4
Jul 21, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/temperature-blend-door-actuator/i/ ... To Install Replace AC Heater Temperature Actuator 2000-05 ChevyMonte Carlo.

2006 Monte Carlo: Blend Door Actuator Replacement ...

? 2:19
https://www.youtube.com/watch?v=_B17o-Ljhfs
Mar 31, 2015 - Uploaded by Adam Strojny
In this video I will show you guys how to replace the actuators behind the glove compartment that where causing ...

Chevy Blend Door Actuator Replacement - Part 3 - YouTube

? 12:26
https://www.youtube.com/watch?v=1q9ugwlqDoo
May 14, 2013 - Uploaded by Dan Abbott
My final step to replacing the blend door actuator. ... Thanks for the video, need to do this on my 04 monte carlo ss, went to use the heat today .... 2003 Chevy Suburban AC-heater air direction problem.mov - Duration: 1:36. by ...

Sounds like the blend door is not moving. Most blend door actuators are located on the bottom of the heater box near the middle of the car. If the temp control is a round knob, it is an electronic actuator.

the blend door actuator located on the air box (right hand side under dash) is prob. inop. worst case senerio the blend door its self is broken. I have replaced the actuator more than anything.

Had the same thing happen to my truck, the blen door actuator is under the console on passenger side, but the heater core is going to be clogged if you dont have any heat coming through, but a/c works..

most likely needs a LH (bottom) temp actuator. Located in the center of the dash on the bottom, you have to remove the hush panel on the rh side of the truck

I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado

1. Remove the floor air outlet duct extension (1) from the floor duct (2). Remove the floor air outlet duct extension (1) from the floor duct (2)
2. Disconnect the electrical connection at the blend door actuator (10). Blend door actuator and related components
3. Remove the blend door actuator mounting screws from the HVAC module.
4. Remove the blend door actuator as an assembly with the actuator cam. Remove the blend door actuator mounting screws from the HVAC module

To install:

1. Install the blend door actuator as an assembly with the actuator cam.
   1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
   2. Line up the A/C valve lever with the blend door actuator cam
2. Install the blend door actuator mounting screw to the HVAC module.
   1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
3. Connect the electrical connection at the blend door actuator (10). Blend door actuator and related components
4. Install the floor air outlet duct extension (1) to the floor air duct (2).

C/K Series

1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
2. Remove the screws.
3. Remove the adjuster links from the control lever.
4. Remove the mode actuator.
5. Adjust the mode actuator by completing the following steps:
   1. Connect the electrical connector to the actuator.
   2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
   3. Turn the ignition switch to the OFF position.
   4. Remove the actuator from the electrical connection. Blend door actuator-C/K Series

To install:

1. Install the mode actuator.
2. Install the screws.
3. Install the adjuster links to the control lever.
4. Connect the electrical connector.
5. Test the circuit operation