2000 Mazda B-Series Logo

Related Topics:

A
Anonymous Posted on Oct 16, 2012

Running rough mazda bravo b2600

Changed distributor and cap, new plugs, leads.

4 Related Answers

Ronaldbrains

  • 881 Answers
  • Posted on Nov 17, 2009

SOURCE: Have Mazda bravo B2600 4WD ,has white smoke &

You dont say weather its a petrol or diesel engine as there a slight differance in the answer and if a turbo on a diesel thats even more of a differance, but taking it a petrol .
Well to start with the white smoke Isent smoke its water and after going through the engine it turns into Steam and thats what you see..
Running on 3 clyinders is caused through 1 cylinder isent working as a engine should and has a bad valve or a broken piston ring or more and even a cracked head and gasket letting the water through,,,also the broken ring works like a oil pump as if not firing given you power then it works like a oil pump and pumps it into the cylinder that dosent work only pumping oil into the hot exhaust system while running.CAUSING SMOKE
And if a turbo then could be the turbo bearings worn and pushing oil into the engine and still doing the same as before.
Let me know how you get on. RON

Ad

Anonymous

  • 1 Answer
  • Posted on Jan 20, 2010

SOURCE: changing gearbox oil ?

i accidently drained some of the gearbox oil from my bravo b2600 1997. where is the hole to put more fluid back in there? how much should i put? and what fluid should i use?

Harry Goodwin

  • 365 Answers
  • Posted on Jun 11, 2010

SOURCE: i need to set up the camshaft timing marks on a 1994 mazda b2600

its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok

Anonymous

  • 677 Answers
  • Posted on May 25, 2011

SOURCE: 1998 mazda bravo ute b2600 petrol- Cannot locate

No!!!! The motor has oil filter.Look from the top of the motor.It is right there.Under the manifold.Hope this helps

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2003 Mazda Bravo b2600 petrol lag in acceleration, new plugs extractors,flow through cat, new air filter,air flow meter, could it be ecu, or throttle control unit , revs hard goes like a slug.

I would check into your transmission at this point and eliminate that before moving on. To have a shop look at it and diagnose is only 80 bucks or so.
0helpful
1answer

Free online auto repair manuals

Did you use factory spark plugs? Try cleaning the throttle body.
0helpful
1answer

Mazda bravo vibration on gears

as the only unit operating when stationary is the engine it points to a problem in that area. assuming that nothing has been done to the gearbox /fly wheel area it points to a faulty firing system ie spark plug or lead or shorting of the lead from dirt or grease. this misfiring equates to an unbalanced engine or vibration
0helpful
1answer

How to change front brake pads on a 91 mazda b2600

how to change disk break pads on 92 mazda bravo 4x4
0helpful
1answer

2003 b2600 bravo ute ignition timing has g6 engine same as ford courier model timing is adjustable as it has an adjustable distruibutor

I have a 2003 model mazda Bravo 2wd G6 2.6l petrol I'm having with the distributor timing thinking it was my crankshaft sensor was a problem but it still doing the same thing it will idle but when u got up ta 1500rpm brake down run ruff and motor would cut out or go back to idle and wouldn't start again till it cool down but i a cleaner into the airflow meter sensor and it drove and down the road with out breaking down
5helpful
1answer

I need to set up the camshaft timing marks on a 1994 mazda b2600

its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok
0helpful
2answers

Changing gearbox oil ?

i accidently drained some of the gearbox oil from my bravo b2600 1997. where is the hole to put more fluid back in there? how much should i put? and what fluid should i use?
1helpful
1answer

The car is a 92 marvie proceed it can run for approx 15mins then starts running rough no power wont rev up sounds like sumthing with the timing we have change petrol filter tried a different coil and a...

I don't know if this will help those b2600 owners, mine was a 92 automatic, it use to have all sorts of problems similar to like rough idling, stalling after it ran for a couple of minutes. Changed fuel pump and filter but did not help.Running out of idea so I removed the ECM (computer) and noticed a blown capacitor (ECM at passenger side kick panel). Goggled the ECM number and found out it is a common issue to that ECM built by Mitsubishi, common to Mazda and Mitsubishi cars and trucks on certain model years. Working fine now for almost a year after I sent it out for repair.
Not finding what you are looking for?

457 views

Ask a Question

Usually answered in minutes!

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...