Lh window inoperable where is the fuse for the window switch?

It's not a fuse problem , your vehicles power windows get battery voltage from a circuit breaker . They don't good bad often . You have control modules (computers ) inside both your front doors . Both of these modules have their own power supply . Pulling the door trim panel an driver door switch an check for battery voltage at the switch would be a better idea . Also hooking a factory or someother type professional scan tool an checking for DTC'S - diagnostic trouble codes in the door modules and or the BCM"S body control module system .

DR MOD PWR C/B 30 Amp circuit breaker

Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a power window switch built into the driver door switch assembly (DDSA) , or, from a power window switch mounted locally on its associated door. The driver door window can be operated only from the driver door power window switch built into the DDSA.
When the driver door module (DDM) receives a driver door window switch request from the DDSA, the DDM examines the request and inspects to see if it has received any messages from any of the other vehicle modules prohibiting the movement. If no prohibitive messages have been received, the DDM then applies power and ground to the driver door window motor to move the window as requested.
When a passenger door module, passenger front door module (PDM), LH rear door module (LRDM), or RH rear door module (RRDM), receives a window switch request from, either the DDSA or the window switch mounted locally to its door, the passenger door module examines the request and inspects to see if it has received any messages from any of the other vehicle modules prohibiting the movement. If no prohibitive messages have been received, the passenger door module then applies power and ground to its associated window motor to move the window as requested.


Your best bet , take it to a qualified repair shop.

Power Windows System Components
The following components are used to control the power windows:
• Driver Door Module (DDM)
• Passenger Front Door Module (PDM)
• LH Rear Door Module (LRDM)
• RH Rear Door Module (RRDM)
• Driver Door Switch Assembly (DDSA)
• RH Front Power Window Switch
• LH Rear Power Window Switch
• RH Rear Power Window Switch
• LH Front Power Window Motor
• RH Front Power Window Motor
• LH Rear Power Window Motor
• RH Rear Power Window Motor
• Class 2 serial data link
• PWR WDO 30 Amp Circuit Breaker
• DRVR MDL 10 amp fuse -- DDSA and DDM logic, DDM internal driver operation.
• PASS MDL 10 amp fuse -- PDM logic and internal driver operation.
• RRDR MDL 10 amp fuse -- LRDM and RRDM logic and internal driver operation.

Principles of Operation
Power Window Operation The power window system operates under the control of the accessory delay relay. The smart junction box (SJB) grounds the relay coil to provide power to the power window system.
The power window system can be operated from the LH front window control switch or from the window control switches located on each door panel. The LH front window control switch has 2 modes of operation for the LH front power window, manual and auto. All other windows operate in the manual mode only.
Manual mode moves the window downward until the switch is released. The LH front power window will operate in the manual mode when the LH front window control switch is pressed to the first detent position.
Auto mode provides the one-touch down (OTD) feature for the LH front power window. The OTD function allows the LH front power window to be completely lowered when the LH front window control switch is pressed to the second detent position and then released. OTD is controlled by the LH front window control switch.
The power window system will only operate if:

• the ignition is in the RUN or ACC position.
• the accessory delay feature is in the active mode.

There is no separate fuse for power windows:
https://www.2carpros.com/questions/nissan-altima-2006-nissan-altima-windows-and-locks

https://oards.com/causes-of-power-windows-not-working/

The following components are used to control the power windows:
• Driver door module (DDM)
• Passenger front door module (PDM)
• LH rear door module (LRDM)
• RH rear door module (RRDM)
• Driver door switch assembly (DDSA)
• RH front power window switch
• LH rear power window switch
• RH rear power window switch
• LH front power window motor
• RH front power window motor
• LH rear power window motor
• RH rear power window motor
• Class 2 serial data link
• DR MOD PWR C/B 30 Amp circuit breaker
• DRIVER DR MOD 10 Amp fuse -- DDSA and DDM logic, DDM internal driver operation.
• PSGR DR MOD 10 Amp fuse -- PDM logic and internal driver operation.
• REAR DR MOD 15 Amp fuse -- LRDM and RRDM logic and internal driver operation

It's not the BCM ,more then likely it's that windows switch .
Rear Door (LH or RH) REAR POWER WINDOW SWITCH LH OR RH OPERATION WINDOW UP When the rear power window switch LH or RH is pressed in the up position Power is supplied ? through rear power window switch LH or RH terminal 4 ? to rear power window motor LH or RH terminal 2. Ground is supplied POWER WINDOW SYSTEM GW-17 C D E F G H J K L M A B GW Revision: January 2005 2004 Pathfinder Armada ? through rear power window switch LH or RH terminal 5 ? to rear power window motor LH or RH terminal 1. Then, the motor raises the window until the switch is released. WINDOW DOWN When the rear power window switch LH or RH is pressed in the down position Power is supplied ? through rear power window switch LH or RH terminal 5 ? to rear power window motor LH or RH terminal 1. Ground is supplied ? through rear power window switch LH or RH terminal 4 ? to rear power window motor LH or RH terminal 2. Then, the motor lowers the window until the switch is released. MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OPERATION WINDOW UP When the main power window and door lock/unlock switch (rear LH) is pressed in the up position Power is supplied ? through main power window and door lock/unlock switch terminal 3 ? to rear power window switch LH terminal 3 ? through rear power window switch LH terminal 4 ? to rear power window motor LH terminal 2. Ground is supplied ? through main power window and door lock/unlock switch terminal 1 ? to rear power window switch LH terminal 2 ? through rear power window switch LH terminal 5 ? to rear power window motor LH terminal 1. Then, the motor raises the window until the switch is released. When the main power window and door lock/unlock switch (rear RH) is pressed in the up position Power is supplied ? through main power window and door lock/unlock switch terminal 5 ? to rear power window switch RH terminal 3 ? through rear power window switch RH terminal 4 ? to rear power window motor RH terminal 2. Ground is supplied ? through main power window and door lock/unlock switch terminal 7 ? to rear power window motor RH terminal 2 ? through rear power window switch RH terminal 5 ? to rear power window switch RH terminal 1. Then, the motor raises the window until the switch is released. WINDOW DOWN When the main power window and door lock/unlock switch (rear LH) is pressed in the down position Power is supplied ? through main power window and door lock/unlock switch terminal 1 ? to rear power window switch LH terminal 2 ? through rear power window switch LH terminal 5 ? to rear power window motor LH terminal 1. Ground is supplied ? to main power window and door lock/unlock switch terminal 3 ? through rear power window switch LH terminal 4 ? through rear power window switch LH terminal 3 ? to rear power window motor LH terminal 1. Then, the motor raises the window until the switch is released

With the electronic's involved ,your best bet would be to take to a qualified repair shop . The door 's have electronic control module inside that control door lock's an window operation . Hooking up a professional or factory scan tool an viewing input data an checking DTC'S - diagnostic trouble code's would be the first step any professional technician would do . You probably have no idea what these are ? Messing with these systems can render your vehicle unuseable if you do not know what you are messing with .

Power Windows System Components
The following components are used to control the power windows:
• Driver door module (DDM)
• Passenger front door module (PDM)
• LH rear door module (LRDM)
• RH rear door module (RRDM)
• Driver door switch assembly (DDSA)
• RH front power window switch
• LH rear power window switch
• RH rear power window switch
• LH front power window motor
• RH front power window motor
• LH rear power window motor
• RH rear power window motor
• Class 2 serial data link
• DR MOD PWR C/B 30 Amp circuit breaker
• DRIVER DR MOD 10 Amp fuse -- DDSA and DDM logic, DDM internal driver operation.
• PSGR DR MOD 10 Amp fuse -- PDM logic and internal driver operation.
• REAR DR MOD 15 Amp fuse -- LRDM and RRDM logic and internal driver operation.
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a power window switch built into the driver door switch assembly (DDSA) , or, from a power window switch mounted locally on its associated door. The driver door window can be operated only from the driver door power window switch built into the DDSA.
When the driver door module (DDM) receives a driver door window switch request from the DDSA, the DDM examines the request and inspects to see if it has received any messages from any of the other vehicle modules prohibiting the movement. If no prohibitive messages have been received, the DDM then applies power and ground to the driver door window motor to move the window as requested.
When a passenger door module, passenger front door module (PDM), LH rear door module (LRDM), or RH rear door module (RRDM), receives a window switch request from, either the DDSA or the window switch mounted locally to its door, the passenger door module examines the request and inspects to see if it has received any messages from any of the other vehicle modules prohibiting the movement. If no prohibitive messages have been received, the passenger door module then applies power and ground to its associated window motor to move the window as requested.

So do yourself a favor an take it to a qualified repair shop.

Faulty switch or relay or brake in the wire so you need to test the wiring to motor see if theres power to motor

Power Window Circuit Breaker: LH Rocker Panel, Near Front Seat
Power Window Relay: LH Rocker Panel, Near Front Seat

check fuses 35 & 41 (10 amp, red).
it also shows an accesory delay relay in the fuse panel.
And fuse 601? 30 amp.

make sure you don't have lock-out on driver switch panel activated.

Power Window System
Features and Operation
NOTE: The accessory delay feature will allow power window operation up to 10 minutes after the ignition is off or until a door is opened.
If equipped with power windows, the window control switch (14529):

• will operate the power windows only when the ignition switch is in the RUN or ACC position.
• is located on each front door trim panel, and Crew Cab and Excursion rear door trim panel.
• may be used to raise or lower the driver side, passenger side and rear windows from the LF control on the driver side, or the passenger window from the passenger switch.
• includes a one-touch down (OTD) feature for the driver door window.
• can partially lower the driver side window when the LF window control switch is depressed half way (first detent).
• will completely lower the driver side window when the LF window control switch is fully depressed and then released (second detent).

Power Window System — Modes of Operation
There are two modes of operation for the power window system.
Manual Mode
When the LH window control switch is pressed to the first down position, the window will move down until one of the following conditions are met:

• The LH window control switch is no longer in the first down position.
• The LH window control switch is pushed to the OTD position, causing the windows to enter auto mode.

Auto Mode
Auto mode provides the OTD feature. The OTD feature is activated when the LH window control switch, for the LH window, is pressed to the second down position.
Auto mode will be terminated when any of the following conditions are met:

• The LH window control switch is pushed to the UP position.
• The LH window control switch is released (OFF position) and then moved to the DOWN position (first detent) or OTD position (second detent).
• Note: Delayed accessory feature must be active.

The OTD feature is controlled by the window control switch.

---------------------------------------------------------
Condition Possible Sources Action

• All power windows are inoperative

• Fuse(s).
• Circuitry.
• LF window control switch.
• Accessory delay relay.

there is a switch on the drivers side that will make all windows inoperable its for child proof .Its with the rest of the windows switches