How do I remove? Got the main bolts. DO I remove bumper, pop out fog lights?
SOURCE: Headlamp assembly on Pontiac G6
well there isn't much on gripping the retainers, what they are, are plastic ball and socket clips. I would lay some tape down underneth the lamp onto the bumper to protect the bumper and then the hard part...while making sure the headlamp is above the bumper, pull with some force on the back half of the light to where it meets with the fender, after a little pulling it should (no promises) should come out, it will seem like it will break but it shouldn't. (I use to work at a body shop and did many of those headlights including my own '06 G6.) Hope that helps.
SOURCE: Bumper cover removal
It is a little more complicated than that. There are two nuts below the headlight assemblies in the engine compartment. You will need to remove the battery and overflow bottle to get at the one on the passenger side. Remove the turn signals in the bumper, then there are 2 or 3 bolts holding a mounting bracket behind the each of the turn signals. There are a number of bolts with washer heads and reatiners on the underside of the bumper as the previous responder indicated.
SOURCE: 2004 toyota rav4 rear bumper assembly guide
there are two bolts to the center and two around the corner on at the edge up high and one at the bottom of the bumper/ Please rate my response thank you very much
SOURCE: how to remove bumper to change the fog lights
YOU SHOULDNT HAVE TO REMOVE THE WHOLE BUMPER.JUST REMOVE THE LOWER BUMPER PLASTIC COVER.
SOURCE: How to change the whole headlight assembly on a 05 Honda CRV
You have to remove the front bumper and grill etc
There are 5 bolts holding the headlight assembly in place. 2 at the top and 3 underneath.
Remove the plastic cross piece by prising out the clips and then the grille clips too then unbolt the bolts eithr side under the wheel arch. The bumper is still fastened using cips. Pull the bumper forward to unclip.
To change the bulbs you need to first
remove the 5 plastic pop screws on the front bumper. They're spread out at the
top of the bumper right under the hood. Once you get those out, you have to
remove the two hex bolts on each headlight. Then it gets tricky. You need to
pull the light towards the front of the car until it pops out of the
ball-bearing type mount on the fender. Once that pops out, you have to pull the
front bumper forward while maneuvering the headlight out towards the front.
As per the manual it says as
follows:---
Open the hood.
Hold the headlamp to prevent damage to
the headlamp or to the fascia. Remove the
bolts from the headlamp assembly. Remove the push-in-retainers across the front
fascia. Remove the headlamp assembly. Lift the headlamp upward to release the
locating tab from the front edge of the fender.
Disconnect the electrical connector
from the headlamp assembly.
Remove the headlamp bulb access cover
by rotating the headlamp bulb access cover counterclockwise, if necessary.
Remove the headlamp bulb from the housing
by rotating the socket counterclockwise, if necessary.
Disconnect the headlamp bulb electrical
connector, if necessary.
Remove the park/turn bulb access cover
by rotating the cover counterclockwise, if necessary.
Remove the park/turn bulb from the housing
by rotating the socket counterclockwise, if necessary.
Gently pull the park/turn bulb from the
socket, if necessary. Install the park/turn bulb into the bulb socket.
Install the park/turn bulb socket into
the headlamp housing by rotating the socket clockwise.
Install the park/turn bulb access cover
by rotating the cover clockwise.
Connect the headlamp bulb to the
headlamp electrical connector.
Install the headlamp bulb into the
headlamp housing. Rotate the socket clockwise until locked.
Install the headlamp bulb access cover
by rotating the cover clockwise.
Position the headlamp assembly to the
vehicle. Lift the headlamp upward to release the locating tab to the front edge
of the fender.
Install the bolts to the headlamp
assembly. Tighten the bolts to 2 N·m (18 lb in).
Install the push-in-retainers across
the front fascia.
Close the hood.
----------This will help.thanks.Helpmech.
Remove the bolts from the front bumper fascia at the fender
Remove the 3 bolts which secure the composite headlamp
To install:
1,969 views
Usually answered in minutes!
×