1991 Plymouth Sundance Logo

Related Topics:

Anonymous Posted on Oct 03, 2012

How do u reset codes on a 1991 plymouth sundance

Can codes be reset then try them to a shop ??

1 Answer

A

Anonymous

Disconnect the battery for a couple minutes

If you have problems, don't clear,a shop will
need the data stored to diagnose

5 Related Answers

Nick DelRegno

  • 49 Answers
  • Posted on Jan 25, 2009

SOURCE: have codes coming up on

Do you know the codes or are you asking for help pulling the codes?  If you know the codes, go here to find out what they mean.  If you need to pull the codes, most auto parts stores will pull the codes for you for free.

Ad

Jeff3fg

  • 124 Answers
  • Posted on Mar 28, 2009

SOURCE: Replacing the heater core on a '88 Plymouth Sundance?

Behind the dash. You will have to pull the whole dash assembly. It looks like a little radiator.

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Aug 08, 2009

SOURCE: i need all the engine diagnostic codes for a 94

11 Timing belt2.gif skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM/ECM was disconnected within the last 50 key-on cycles (normal)
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failur

66 chrgr

mike loshbough

  • 1011 Answers
  • Posted on Sep 24, 2009

SOURCE: 1989 plymouth sundance obd1 code 11 car dies when

The code 11 is referring to your coil pickup.This is located under the distributor cap and rotor,and is held in by the distributor cap itself.Being electrical when it gets hot the sensor brakes down .The pickup is not very expensive at all:)

Anonymous

  • 1776 Answers
  • Posted on Oct 07, 2009

SOURCE: I need a shop manual for a 1993 plymouth sundance

If you visit the autozone.com website and register your car information, it will give you access to an online repair manual for the car. It is a really handy resource for automotive maintenance that I think you will find helpful. It's free of charge. Hope this helped and best wishes.

Testimonial: "Very helpful, thanks"

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What code 44 on a plymouth sundance 1991

Generally speaking, code 12 means the battery has been disconnected at some point in time.
Code 44 means the battery temp sensor circuit is out of normal range, too high or too low.
0helpful
2answers

When trying to start my 1991 Plymouth Sundance America I hear only a clicking sound. I replaced the battery but it did not work. Can it be the alternator?

sounds like you have a bad starter.not your alternator.if the battery is good the car should start even if the alternator is bad.you can even drive the car until the battery runs low.the alternator job is to keep the battery charged.soulds like the solinoid is clicking.but no responce from the starter.have starter checked.

I’m happy to help further over the phone at https://www.6ya.com/expert/kenneth_3efc1f8510674f04

0helpful
2answers

Where is the computer located on a 91 plymouth sundance. I think this is causing the voltage to jump to almost 18V and the grounds have been checked and the altenator replace and still having problems so I...

need to know if 2.2 or 2.5 if 2.5 need to know if turbo, i would get the alternator checked because the voltage regulator is in alternator not computer, just cause new alternator doesn't mean good, have it checked out
1helpful
2answers

Where is te starter on a 1991 plymouth sundance what is it hooked

The starter is located on the bottom of the engine, where the engine and transmission meet. It is on the side of the engine closest to the front of the car. The easiest way to find it is to follow the positive battery cable, as it goes directly from the battery to the starter solenoid.
1helpful
1answer

Where is the staretr located on an 1991 plymouth

On the side of the engine block above the oil pan faceing the transmission.
0helpful
1answer

How to fix emergency brake on 1991 plymouth sundance. when i push down all the way the brake light in the dash comes on but the car doesnt stop

There is a wire split under the car on driver side,but follow the wire and you should run into the prob.
1helpful
1answer

How do i grease the ball joints of a 1991 plymouth sundance

Hi I'm litoshop to to grease the ball joints it will be easier to take the tire off and you will see the grease bits it looks like a little nipple and if it does not have one you can buy them and put them on good luck
0helpful
1answer

Intermittant loss of acceleration on my 1991 plymouth sundance

Turn key, on, off, on, off, on & leave it on (not start) & count check engine flashes. 2 digit codes, for example: flash, flash, flash, pause, flash,flash., is code 32
Not finding what you are looking for?

137 views

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...