2004 Dodge Stratus Logo

Related Topics:

Posted on Oct 02, 2012

2004 dodge stratus 2.4 dohc po344 code - 2004 Dodge Stratus

1 Answer

A

Anonymous

PO 340 thru PO344 are cam shaft position sensor issues

That does not tell you what is wrong or to replace anything

Have it diagnosed at a repair shop

A sensor could fail & it more than likely is just
reporting other issues you have to have resolved.

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Sep 18, 2009

SOURCE: I'm getting the engine light coming every so

I have a 2004 dodge stratus 2.4 dual overhead cam. When driving down the road, bell goes off, check engine light comes on, and it's like I'm driving on limp mode, when going over 2000 rpm's, there's a severe stutter. After getting code for light it points to cam shaft sensor, which i changed. I also changed crank shaft sensor. After all of this was done, drove great for about 30 miles and the same thing happened all over again. If anyone can point me in the right direction it would be greatly appreciated.

Ad
emissionwiz

Marvin

  • 85242 Answers
  • Posted on Dec 02, 2008

SOURCE: 2004 Dodge Stratus 2.7 thermostat location

Finding the thermostat: Follow the LOWER radiator hose to where it meets the engine. It's in there. Most cars that I've worked on have the thermostat at the end of the upper radiator hose, but not this car. Replacing the thermostat: You need to remove the thermostat housing. (It's the piece that the lower radiator hose connects to.) - You do not need to remove the radiator hose from the housing. - First remove the bolt that is holding a bracket. This bracket just holds some wires in place. - Now remove the three bolts that hold the housing to the engine block. These bolts can be fairly hard to turn, but just keep trying. - Gently pry the housing away from the engine block. You can use a flat-head screwdriver to help pry, but do not scratch the mating surfaces of the housing and the block. - Pull out the thermostat, noting that the spring end goes into the engine. - When you put the new thermostat in, you probably want to use a new black rubber gasket, but you might be able to use the old one if you have no choice. Also, I didn't add any permatex or anything and it seems fine. - I tightened the bolts to 22foot pounds, but this might be a little high. Whatever you do, DO NOT overtighten the bolts. Couple other notes: I first removed the air cleaner cover and tubes to get a little more working room. I also unplugged one wiring harness to make more room. Otherwise, I was able to get my big hands in there. A new thermostat did not fix my problem. Here is a description of the problem I was having and the solution: Problem: The temperature gauge was spiking occasionally, all the way into the red. It would spike up and come back to normal. It would spike usually while in idle, but sometimes while driving. Usually about once every twenty minutes. Things I checked first: - The plastic reservior for the radiator was full to the top. - The electric fans were running, and running on high speed. - The car had working heat. - Replaced the thermostat. Did nothing to help the problem. Problem Found: - Vapor lock. Even though the reservior was full of fluid, it had previously gotten too low and the system sucked in some air. Once that happens, it doesn't matter if the reservior is full, the cooling system will not draw in the coolant. This is because filling the plastic reservior does not pour coolant directly into the cooling system. The coolant is sucked into the cooling system through a tube, like drinking soda through a straw. So the reservior, where they tell you to add coolant, was full but the cooling system (radiator, engine, pump, etc.) was almost out of coolant and wasn't able to draw in any more. Solution: When the engine is cool, open the metal radiator cap that's sticking right up out of the engine. It can be found by following the upper radiator hose to the engine. There is a tall metal tube with a metal cap on it. Pull that cap off (when it not hot) and fill it up with radiator fluid. (I use radiator fluid that's pre-diluted and designed for all makes and models of cars). Idle the car, in park, for about thirty seconds. Stop the engine and put the cap back on. If you're lucky, all the air bubbles are out of the system and you're all set.

Anonymous

  • 1861 Answers
  • Posted on Mar 06, 2009

SOURCE: MAF Sensor 2004 Dodge Stratus

If your car has a MAF (Mass Air Flow) sensor, it would be located in the air delivery tube that runs from the air filter box to the throttle plate assembly on the intake manifold. It will have a wiring connector going to it, also. The MAF does exactly what it is called: It "senses" the volume, or "mass" of the air-flow; thusly it needs to be in the intake air tube. If you do NOT have such a device in the air-tube, you have a MAP sensor, (Manifold Absolute Pressure); this is another way of measuring the same air volume, albeit older technology. You will commonly find this device on the firewall, with a vacuum line running to the intake manifold.

I hope that this sheds some light on your question.

Thanks for choosing FixYa for advice!

Anonymous

  • 84 Answers
  • Posted on Feb 03, 2010

SOURCE: dodge stratus 2004 head light bulb replacement

Headlight Bulb Replacement
1. Open the hood and remove the two headlight mounting
screws.
2. Remove the push-in fasteners for the grill area by prying under the
head of the fasteners with a flat bladed tool.

Anonymous

  • 121 Answers
  • Posted on Jan 16, 2011

SOURCE: 2004 dodge stratus 2.7 dohc

they work together. be absolutely sure you have them right because if not you run the risk of doing some head damage

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

No ingnition fire on cylinders 2 and 4 2004 dodge stratus 2.4 L engine

Easy! The DIS module has failed...!

The Stratus 2.4L engine uses what is called "a wasted spark" ignition system, that feeds two cylinders with the same ignition coil. Havind a pair of Cylinders dead means one of the coils or the module is inoperative. Amclaussen.
0helpful
1answer

2004 Dodge Stratus 2.4 liter Fuel pressure

Fuel pressure should be around 50 psi +/- 5 psi. So anywhere from 45-55 psi is normal.
0helpful
2answers

Firing order messed up, car will not start

2004 Dodge Stratus Sedan
2.7 liter DOHC V-6 VIN "R"92773275.gif
1helpful
1answer

Spark plug firing order

2.4L SOHC/DOHC 1-3-4-2 2.7L DOHC 1-2-3-4-5-6
3.0L SOHC 1-2-3-4-5-6
0helpful
1answer

Engine cuts out @2400 rpms

Check the crank sensor. This is very common for this problem. Best wishes!
4helpful
1answer

I'm getting the engine light coming every so often. It seems that after I fill the tank and get down around 3/4 tank, The message I'm getting is "EVAP Emission Control System Purge Flow Fault". PO441 and...

I have a 2004 dodge stratus 2.4 dual overhead cam. When driving down the road, bell goes off, check engine light comes on, and it's like I'm driving on limp mode, when going over 2000 rpm's, there's a severe stutter. After getting code for light it points to cam shaft sensor, which i changed. I also changed crank shaft sensor. After all of this was done, drove great for about 30 miles and the same thing happened all over again. If anyone can point me in the right direction it would be greatly appreciated.
Not finding what you are looking for?

440 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...