SOURCE: 1994 dodge caravan check engine light comes on
These are all the definitions for your codes.
It's hard to give an exact cause for these codes because of there are a number of different items that could cause these.
The first one could be caused by Incorrect camshaft timing,
VCT solenoid valve stuck open or continuous oil flow to piston chamber,
Camshaft advance mechanism binding, or faulty VCT unit,
The others are most likely bad sensors.
I wish I could be more help but it's difficult to trouble shoot this kind of problem without having the vehicle here in front of me.
Good luck
P0012 "A" Camshaft Position - Timing Over-Retarded (Bank 1)
P0032 HO2S Heater Control Circuit High (Bank 1 Sensor 1)
P0055 HO2S Heater Resistance (Bank 1, Sensor 3)
SOURCE: I cannot get the alternater out of my 1997 Dodge
3.3L & 3.8L Engines
Alternator removal-3.3L and 3.8L engines
To install:
LET ME KNOW IF THIS HELPED.
SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan
3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!
SOURCE: 1994 dodge caravan le hood release cable broke how
Most of these cable that break usually break at the connector under the dash. If this is the case you can still open the hood just find where the cable connects and pull this it should open the hood.
SOURCE: 2007 dodge grand caravan
where are the bolts to remove the caliber on the rear brakes for a 2007 dodge caravan?
connect into the distributor cap. If you don't see a distributor, you may have a model with a distributorless ignition system.
Step2
Find the ignition coil. On a Dodge Caravan,
the ignition coil is at the back of the intake manifold. Disconnect the
negative battery cable to prevent injury while you work.
Step3
Determine whether you need to remove the windshield wiper/motor module assembly. This won't be necessary on all models.
Step4
Disengage the connector securing the wiring harness connector to the Dodge Caravan ignition coil. Then, disconnect the ignition wire from the ignition coil.
Step5
Use a socket set to remove the mounting bolts. There are upper and
lower mounting bolts. Separate the ignition coil from the mounting
bracket.
Install the New Ignition Coil
Step1
Insert the new ignition coil. Mount the Dodge Caravan ignition coil to the mounting bracket.
Step2
Attach the mounted assembly to the intake manifold. With a Torque
wrench, tighten the fasteners securing the ignition coil to the
mounting bracket with 96 inch pounds of torque (10 Nm).
Step3
Tighten the bolts that secure the intake manifold to the bracket with 115 inch pounds of torque (13 Nm).
Step4
Connect the wire harness and any other parts you removed, including the negative battery cable.
169 views
Usually answered in minutes!
×