Trunk won't open with either remote but will open with trunk button on drivers door

Archaeology

• 662 Answers
• Posted on Aug 15, 2011

SOURCE: My trunk won't open, I

There are 3 phases to fixing your car's trunk lid release problem.

Phase 1: First check the fuse - once you know that's OK, then proceed to phase 2 (below).
The fuse for the trunk lock is
the bcm (pwr) 15A fuse in the instrument panel fuse box (behind panel at drivers right foot)

Check that fuse, as it is the power supply for the button on the dash that sends power to the actuator in the trunk.

Phase 2: Get the trunk open (without taking it to the dealership).
If you have remote keyless entry to the trunk, you could try that - but with the actuator
dead/dying, it shouldn't work.

Here are a couple of ideas to try to enter trunk while (a) actuator isn't working, and (b) all
valet lockout features (designed to deny valets access to the trunk) are in the "Lock" position:

There is the lock cylinder, which you stated is not functioning - put the key in, and it doesn't
turn. Just to be sure, consider: lubricate key with Graphite lock-type lubricant, and retry.

The trunk has 2 valet safetys...the locking rear seats which require access to the trunk to unlock, and then there is a valet switch in the trunk that locks the button on the dash from working to keep valet parking attendants out of the trunk. That may be in the lock position.

You can try accessing the center area of the fold down rear seat and see if you can unhinge the rear seat from there. Maybe reach in with your hand, or an extension-type tool.

there may be a way to fold the hinge away from the seat back so it can be removed from the hinge and give you access to the safety latch in the trunk and open it that way (white handle in trunk).
The white-handled safety latch release is desiged to prevent accidentally trapping children, and
if you can pull it with your extending-type or grasping-type tool, the trunk will open whether or
not the actuator motor is working.

Phase 3: Replace the Problem part.

Your failed part may be either (1) Trunk Release Relay, or (2) Trunk Lock Release Switch

My Satrun ION manual doesn't cover either of these parts, and the online parts houses, e.g.
http://www.rockauto.com/catalog/x,carcode,1431624,pgname,Electrical-Switch%2B%2526%252338%253B%2BRelay,a,search.yahoo.com%2BSearch%2Bfor%2B2004%2BSATURN
fail to provide instructions. One of those times a mechanic has to t=rely on his/her native
handiness and/or experience.
To identify which of these parts is bad, locae the Trunk Release Relay (call your dealer parts
dept. for helpful tips on finding it), then operate the dashboard trunk release button with your
ear close tothe relay - if it makes a noise, the problem is the Trunk Lock Release Switch in
the trunk lid, otherwise its the relay.

SOURCE: Trunk release will not work, but I can open it with my key

inside the trunk near the latch is a switch that kills the trunk remote

SOURCE: TRUNK WONT OPEN WITH TRUNK RELEASE BUTTON ON DASH OR WITH REMOTE

Check for broken wires running from the body to the trunk lid through the rubber boot.When the trunk is closing you can see the kink in the rubber boot.There are 11 wires to supply 1 solenoid so I think Chrysler knew there was problem.

SOURCE: trunk release button in 02 Mazda Millenia P

I had the same problem--I agree with JDubbs there is a switch in there and it may be turned that you can't open the trunk from the inside.

SOURCE: trunk release button won't work, remote will

not entirely sure about your buick, but I have a 2000 pontiac that has a switch just inside the glovebox that deactivates the trunk switch. that, together with locking the glovebox would prevent someone with jsut the valet key from gaining access to the trunk area.