Question about 2008 Dodge Grand Caravan

1 Answer

2008 caravan power sliding door not working

The drivers side passenger power sliding door is not working. I can only open and close it manually the power windows dont even work the right side works fine.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 53,168 Answers

The 30A fuse J11 in the totally integrated power module (TIPM) protects the driver side power sliding door module. The 40A fuse J3 in the totally integrated power module (TIPM) protects the left rear door module. If these two fuses are good, the modules may be defective.

Posted on Sep 10, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2005 dodge grand caravan sliding door problems

could be a partially broken wire in the wiring harness that runs in the door track. the wires are inside what looks like a plastic chain that allows it to move with the door and have seen them partially break not allowing power to flow the whole time

Posted on Feb 19, 2009

  • 26 Answers

SOURCE: Power sliding door doesn't work!

Try taking off the door, or spray some wd-40 on the rail. It sounds like its either not getting enough power or its getting caught on something.

Posted on Apr 23, 2009

  • 323 Answers

SOURCE: power sliding door opens part way

Replace the wire track harness in the lower door opening.

Posted on May 29, 2009

  • 116 Answers

SOURCE: Grand caravan sliding doors problems

the door track cable on the right side will have a broken wire in it,the drivers side will be the door control module inside the door

Posted on Sep 04, 2009

  • 1 Answer

SOURCE: Automatic Sliding Door problems on 2005 Dodge Caravan

We have the same problem, just opposite doors - the passenger slider will close to 80%, but the driver still functions fine. There must be an easier solution than new wiring harness/motor??

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Passenger Sliding Door Won't latch close on 2001 Chrysler Town and Country Van AWD


you will need to remove the fuse for the power side doors and back. Disconnect the battery to reset the ECU and the doors should open and close manually just fine. There is a safety release on the gas filler port to prevent the door on that side from opening with the port is opened. Make sure the fuel filler cap door works properly, if the sliding door on that side is the one that won't open.

Aug 10, 2017 | Chrysler Cars & Trucks

2 Answers

My honda odyssey ex 2008 the doors do not move on


Do a reset on the door system, by pulling the door fuse. I don't have location, possibly drivers side fuse box.

Sep 15, 2014 | 2008 Honda Odyssey

1 Answer

The power side passenger door for a 2001 Chevy Venture van works every so often. The door doesn't move when the button is pressed on the panel in the headliner. The key remote doesn't work most of the time...


The proper way would be to look at a wiring diagram an test the electrical circuit's with a DVOM - digital volt ohm meter . Do you know how to test automotive electrical circuit's ?
Electric Testing Techniques You Need to Know
The Trainer 32 How To Read An Automotive Block Wiring Diagram
Free wiring diagrams here http://www.bbbind.com/free_tsb.html
Enter the vehicle info. year , make model and engine size . Under system click on body & accessories ,then under subsystem click on power sliding door . Click the search button then the blue link. Looking at the diagram you will see a control module is used .
Also reading factory service info. on how it works would be a good idea.

Rear Side Door Actuator Control Module
The rear side door actuator control module is capable of on-board diagnostic functions described in On-Board Diagnostic Features . The rear side door actuator control module monitors the door position at all times including during manual operation. After activating the on-board diagnostic modes, loosing battery voltage, or ground to the rear side door actuator control module the Power Sliding Door (PSD) Re-Initialization procedure must be performed in order for the rear side door actuator control module to correctly determine the door position.
Power Sliding Door System Description
The power sliding door system(s) can operate correctly only if the power sliding door is in proper mechanical condition. Any mechanical problems will affect the power sliding door operation and must be repaired before attempting to diagnose the power sliding door system. Manually open and close the power sliding door to determine if the door moves smoothly and without excessive resistance or binding. The power sliding door must also latch and unlatch without the use of excessive force. At any time during power sliding door open or close operation, excessive resistance to the door movement will cause the power sliding door to stop and reverse the direction of travel.
The power sliding door will operate only when the power sliding door on/off switch in the overhead console is in the on position. At anytime during power sliding door operation the on/off switch may be turned to the off position and the system will quit any function in process. The power sliding door will not open unless the transmission shift lever is in the park position and the door is unlocked. When the sliding door security lock is in the locked position the power sliding door will not open from the inside. The power sliding door close function will operate when the vehicle is in gear. The power sliding door module uses the VSS signal to determine if the vehicle is moving during a power sliding door close function. The momentum of the vehicle moving forward adds resistance to the door closing operation. When the rear side door actuator control module determines the vehicle is moving forward while closing the door, current flow through the actuator motor is increased instead of being reversed. The VSS signal circuit is supplied battery positive voltage through a resistor then monitored within the rear side door actuator control module. The VSS signal circuit is then pulsed to ground, or pulled low by the powertrain control module in relation to vehicle speed. The sliding door alarm will sound repeated short tones whenever the power sliding door system is turned on and the door is open while the transmission is out of park.
When the power sliding door system is on and manual operation of the power sliding door is detected the rear side door actuator control module activates the power assist feature. When the power assist is activated the power sliding door will continue to open or close without any further manual effort.
The power sliding doors may be operated using the Remote Keyless Entry System. The keyless entry transmitter will have one OPEN/CLOSE button with a van symbol on it for each power sliding door. The power sliding door ON/OFF switches in the overhead console must be in the ON position in order to operate the power sliding doors using the keyless entry transmitter. When a right hand power sliding door OPEN/CLOSE function is activated using a keyless entry transmitter the exterior lights will flash once indicating the RKE module has received the OPEN/CLOSE command. When activating a left hand power sliding door OPEN/CLOSE function with the keyless entry transmitter the exterior lights will not flash.

On-Board Diagnostic Features
The left and right power sliding door systems operate as independent systems. The on-board diagnostic modes are entered and operate the same in both systems.
The power sliding door systems are capable of the following on-board diagnostic functions:
• Diagnostic Mode 1: An audible signal indicates the diagnostic trouble codes stored by the rear side door actuator control module.
• Diagnostic Mode 2: An audible signal indicates when inputs to the rear side door actuator control module are active.
• Diagnostic Mode 3: Performs an output test of the sliding door unlatch actuator.
Entering On-Board Diagnostics
The on-board diagnostic modes can only be entered in a sequential order from modes 1-3.
• Enter the right power sliding door system on-board diagnostics using the right B-pillar open/close switch and the right on/off switch in the overhead console.
• Enter the left power sliding door system on-board diagnostics using the left B-pillar open/close switch and the left on/off switch in the overhead console.
1. Both power sliding doors must be closed and in the latched position.
2. Place the ignition switch in the OFF position.
3. Place the on/off switch in the overhead console to the OFF position.
4. Press and hold the B-pillar power sliding door open/close switch.
5. While holding the open/close switch, operate the on/off switch through 10 ON and OFF cycles within 10 seconds stopping in the on position.
6. The sliding door alarm will sound 1 long tone indicating diagnostic mode 1 is active.
Diagnostic Mode 1
Upon activating diagnostic mode 1, DTCs will begin to be signaled by the sliding door alarm. The DTCs are 2 digit codes and the codes are represented by the number of buzzes for each digit of the code number. For example a DTC 12 is represented with the following sequence: buzz, pause, buzz, buzz, long pause. Each DTC will be signaled 3 times before proceeding to the next DTC. Refer to Diagnostic Trouble Code (DTC) List . The DTCs will continue to be repeated in this manner until the on-board diagnostics are exited or mode 2 is entered. When exiting the on-board diagnostics all stored DTCs will be erased from the rear side door actuator control module memory.

Oct 13, 2017 | 2001 Chevrolet Venture

4 Answers

Passenger side window stuck in down position


Volcompunker is on track.... if it is a stuck motor problem, before taking door apart, try this...it may work, works well on dodge caravans...

NO COST and fast PROCEDURE TO FIX IT:

1. Sit in vehicle, on seat next to problematic window
2. Ignition key is on
3. Door in question is opened (in case you closed it)
4. While door is open, press and hold power window button in desired window travel, keep button pressed !!
5. SLAM hard the door closed with one hand while other hand holds button as per #4.
6. Watch window operate as it should.

7. Repeat 3-6 if necessary, but usually the first try works!

Jul 11, 2010 | 2001 Ford Expedition

2 Answers

98 buick century power windows dont work


CHECK POWER WINDOWS 20 AMP CIRCUIT BREAKER.

Jan 24, 2010 | 1998 Buick Century

1 Answer

Automatic Sliding Door problems on 2005 Dodge Caravan


We have the same problem, just opposite doors - the passenger slider will close to 80%, but the driver still functions fine. There must be an easier solution than new wiring harness/motor??

Aug 19, 2009 | 2005 Dodge Caravan

2 Answers

Power windows and locks do not work at the drivers door switch. Switch is good and door locks work with the remote any suggestions. I have power to the switch.


sounds to me like a bad body control module. it controls locking/unlocking of all doors, up and down of all windows, opening and closing of power sliding doors, etc...

Jul 05, 2009 | 1999 Chevrolet Venture

2 Answers

Malfuntioning driver's side power window upon opening door lever.


get it to the dealer asap.

you definitely need to take apart the door. There's something not right inside.

May 24, 2009 | 2002 Porsche 911

2 Answers

VW Polo 2001 - Electric Windows wont open from Drivers side..


I removed all 3 switches from driver and passenger door, which is really easy with a flat head screw driver. took them completely apart, very carefully, with a small screwdriver out of a christmas cracker. put them back together again and 2 switches started working, so I put 1 in the drivers side and 1 in the passengers side so now my drivers door window opens and I lean over to open the passenger door. cool, no money spent...yet ;o)

Mar 25, 2009 | 2001 Volkswagen Golf

3 Answers

1999 Jeep Grand cherokee


Check the wiring between the drivers door and the A pillar(the body of the car). Sometimes the harness breaks from opening and closing the door.

Nov 07, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2008 Dodge Grand Caravan Logo

3,356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...