Question about 2005 Nissan Almera 1.5

1 Answer

My nissan Almera S reg has no side lights or dash lights.All fuses seem ok.

Posted by on

  • frank brennan Sep 12, 2012

    The fuse for the side and dash lights is in the fuse box under bonnet near battery.Marked on lid as tail.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 58 Answers

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Posted on Sep 10, 2012

  • frank brennan Sep 12, 2012

    Thanks for your reply, I did find the problem when i checked the fuse with a test light.The fuse looked ok but it was in fact open. The fuse for the side lights and dash lights is in the fuse box under the bonnet near battery and marked on lid as tail and is 10 amp. Hope that helps someone.

×

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 40 Answers

SOURCE: Nissan Almera Air Con Advice

It may be low on refrigerant if the pressures are to low, the compressor will not engage.

Posted on Aug 01, 2009

Anonymous

  • 60 Answers

SOURCE: Nissan Maxima 2000 - no dash board lights, no tail

had same problem on my supra come to find out it was a relay switch back between the tailights

Posted on Jul 12, 2009

Anonymous

  • 1 Answer

SOURCE: nissan almera problems side light

heater blowing cold air only

Posted on Jan 04, 2010

Rob Nevers

  • 86 Answers

SOURCE: engine malfunction warning light on,noticed black

Have some one scan your car for diagnostic trouble codes. There is an emmision control fault that should be taken care of or it could lead to further problems. The fluid coming out of the tailpipe is normal. Gasoline has a certain percentage of water in it and what doesn't get evaporated comes out the taipipe.

Posted on Jan 31, 2010

emissionwiz

Marvin

  • 85206 Answers

SOURCE: nissan almera ecu light

disconnect the battery negative cable for 5 minutes

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of nissan almera tino crankshaft sensor


if you are under the car it should be on the firewall side. It is black piece or a light grey color.

Jan 08, 2016 | Nissan Cars & Trucks

1 Answer

2001 Nissan Almera E 1495cc - Can you please tell me where I can locate the fuse for the cigarette lighter ?


Under your dash board usually on the driver side of the vehicle you should see an access panel or a fuse block either on the kick panel, lower outside of the dash, or on the firewall itself. There you will find the fuse you are asking about. If for any reason you cant seem to find the right fuse, refer to your owners manual.

Dec 31, 2010 | Nissan Se R Cars & Trucks

1 Answer

Nissan almera brake lights not working,checked fuse okay,changed bulbs still not working i don`t whats wrong.


Check the brake light switch under the dash at the brake peddle and make sure its working if it does not close when you depress the brake peddle the lights will not work You may hve to remove the lower cover for the dash to get at the switch

Aug 15, 2009 | 2003 Nissan Altima

2 Answers

Nissan Almera Air Con Advice


It may be low on refrigerant if the pressures are to low, the compressor will not engage.

Jul 31, 2009 | 2000 Nissan Altima

Not finding what you are looking for?
2005 Nissan Almera 1.5 Logo

1,489 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...