Question about 2000 Toyota Corolla

1 Answer

Does any 1 know , how can i find the complete dashboard wiring?? thx

I pulled the old dashboard and put the other new dashboard in , but now when i connect the battery terminals without ignition key the ignition lights are on in dash, and when i try to start the car it wont start. i think i did some thing wrong with wiring or no any idea..

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Toyota Master
  • 1,121 Answers

My dear friend since you know that really did something which is true,why don't you ask a specialist help to avoid the risk of either blown anything vital on the rest of the car or cause a fire and loose not only the dashboard but the car as well.

Posted on Sep 05, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: ignition locked; dash light of car outline with key inside flashs

Get the steering wheel to move even just a little bit and it will unlock.

Posted on Jan 12, 2009

  • 9 Answers

SOURCE: Car Dies while driving and/or Wont even start after being driven

I would buy a cheap Votage meter from Walmart or Radio Shack and check voltage at the Battery. It should be 12.5 or more. Red positive lead of meter goes to red Battery wire. Black lead goes to black Battery wire on top of Battery.

You can check Alternator charging too, the same way The Voltage should jump to 12.8-13.5 volts. My Toyota would shut off and then start back up after moving the connection to the big fuses in the engine compartment Good Luck.

Posted on May 27, 2009

duane_wong
  • 6826 Answers

SOURCE: 2005 Corolla won't start (not even attempt to turn

How about a new lock cylinder for the ignition switch?

Posted on Jul 22, 2010

  • 1 Answer

SOURCE: I have a 2000 toyota avalon ignition problems

Hello I have simular problem the ignition on is stuck in that position with the key turned off and out of the ignition switch.It feels like the key switch is spinning freely in the ignition. Do I need an ignition switch?

Posted on Aug 05, 2010

emissionwiz
  • 85108 Answers

SOURCE: 1996 Toyota Camry. Bought new

I will assume you have a factory Anti-Theft system. Here is the rest procedure unlock the system which was triggered by the battery change and resultant loss of power. Do the reset exactly as written.

Put the key in the ignition, and turn forward
all the way just before cranking position. Then within
5 seconds, locate, press and hold in the
valet/overide button, found under the
dash area, (push button, spring loaded)
until the installed LED (the blinking light)
in your dash area goes on solid,
and the siren chirps once.

(Your valet switch might be the toggle
(on/off) type. in this case, key on,
flip switch in opposite direction,
then turn the key off.)

This should reset the alarm, and reset
the grounded relay on the starter wire,
allowing you to start the engine.

Posted on Apr 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car started out by stalling when I put the right turn signal on but would start back up. Now it died and will not start back up has new battery. the dash lights come on but when you turn the key


Sounds like you might have wire problem.
Try turning the key to the point before ignition. This is actually a dashboard test that have all lights on the dashboard turn on. Try to see if the lights are completely bright or a bit dull in the light.

You battery might be uncharging itself, instead of charging. I have tried that. even with an only 1-2 day old battery.

Dec 03, 2014 | 2000 Buick Century

1 Answer

Turn signals stopped working but were working yesterday. Any ideas?


More than likely the electronic turn signal flasher is defective.
Instructions
  1. Remove the Old Flasher Relay
    • Using your socket wrench, disconnect the negative cable from the car's battery terminal. The negative terminal and cable are identified on the top of the battery using the minus ("--") symbol. Once the cable is disconnected, wrap the metal end completely with the black electrical tape. Lay the cable down and make sure it's not touching any metal surfaces.
    • 2Open the driver side front door and kneel or position yourself so that you're able to see under the dashboard.

    • 3Locate the automotive flasher relay under the dashboard on the right-hand side. The flasher relay is about the same size as an ice cube. It will be held in place by one screw and will have a three-pronged wiring harness connected to it.
    • 4Remove the screw holding the flasher relay in place and slowly lower it from underneath the dashboard.
    • 5Hold the flasher relay in one hand, and with the other hand gently disconnect the wiring harness plug from the relay. Never separate the flasher relay by pulling the harness off by the wires, always hold the plastic harness plug itself.
    Install the New Flasher Relay
    • 6Inspect the new flasher relay to make sure it isn't damaged. Hold the new flasher relay and the old one side by side and compare them, ensuring that they are exactly the same.
    • 7Carefully plug the wiring harness connector into the new flasher relay. Make sure no other wires are intertwined as you raise the flasher and harness back into position under the dashboard.
    • 8Secure the flasher relay by returning its mounting screw.
    • 9Unwrap the negative battery cable's connector and reattach it to the car's battery terminal. Turn the power on or start your car and test out the new flasher relay to make sure it's working properly

Nov 08, 2012 | 1998 Ford Taurus

1 Answer

How to install a headlight switch in a 2001 chevrolet suburban


  • 1.Park the vehicle on a smooth, level surface and set the parking brake. Tilt the steering column to its lowest position.
    2
  • Place your right foot on the brake. Put the key in the ignition and turn it to the "On" position, but do not start the truck. Shift the gear shifter to its lowest position.

    • 3

  • Grab the dashboard bezel that goes around the radio and the gauge cluster with your hands, and pull it toward you to release the clips that hold it in place. Then unplug the wiring to the headlight switch and any other accessories on the panel (which change depending on what model of Sierra you own), using your hands. Pull the bezel away from the dashboard, and put the Sierra's transmission back in "Park."
  • 4Place the dashboard bezel face down on a work surface. There are two tabs on either side of the dashboard bezel holding the headlight switch in place. Use the flat-head screwdriver to gently pry these apart one at a time, then pull the switch out of the bezel. Be careful, because depending on how brittle your dashboard is, you can break these tabs fairly easily.
  • 5Push the replacement switch into the dashboard bezel. Then put your foot on the brake again, shift the truck into the lowest gear, and reinstall the wiring to the bezel using your hands. Push the bezel onto the dashboard to secure the clips, then put the truck back in Park and turn off the ignition
  • Jun 24, 2012 | 2001 Chevrolet Suburban

    1 Answer

    Park light Intermittent


    Workshop manual or youtube , I would try youtube first and put in the same words and go through all the answers ps youtube is my bible for things like this good luck colin

    Jun 15, 2017 | 2007 Toyota Corolla

    1 Answer

    I have a1998 gmc pick up. blower only works on high. i know its the blower motor restor.and i know where it is.but how do you get it out and install the new one. do i have to pull the dashboard out?


    You can on most all vehicles access it by removing or completely opening the glove box door. It is mounted with a couple small screws to the side of the heater motor, (just above the passengers feet) and will have a wire harness plugged into it. Once removed, you will see the coiled resistors that are burnt.

    Mar 10, 2011 | GMC K2500 Cars & Trucks

    1 Answer

    How to install a oxygen sensor on a 2000 Oldsmobile Silhouette


    There are usually two O2 sensors one on each side of the catalytic converter. Each has a wiring assemble and they are screwed into the exhaust system itself. You will need to have the engine exhaust cold as there is a risk of burn injury if it is not. Simply remove the old one usung the proper wrenches and disconnect the wiring at the connector. Reinstall the new sensor and reconnect the wiring at the connector. Make sure that the sensor is completely seated. If you have any questions please ask.

    Thx
    Deathstalker

    Sep 01, 2009 | 2000 Oldsmobile Silhouette

    1 Answer

    Please help: Connecting to the dashboard light


    Do you own and know how to use a 12 volt test light? If so you will have to pull outthe instrument cluster and use the test light to determine which wire is the dash light feed. While you have the cluster out you should see some groung trees under there just gound your other wire there. Sometimes there is a light in the ashtray that is easier to get to that pulling the cluster. Just tap into that wire and you can use the cigar light ground wire for your ground. Go buy a pack of scotch locks and some wire and get to it. Also if you are a DIY you really need a test light.

    Dec 25, 2008 | 2003 Chevrolet Venture Passanger

    1 Answer

    Dashboard Light Replacement


    I've done this and it's a bit of a pain. First drop the steering wheel by taking out the four bolts underneath. You don't need to disconnect anything, it will just pivot downward so that it is not in the way of the dash. Then take out the screws holding the dash and pull it off. Next you'll need torx bits to undo the instrument cluster. It is not necessary to take off the plastic faceplate. Just take out the rearmost screws and the cluster should be movable, but not enough to get it out far enough to reach the bulbs from the rear. For that you have to disconnect the speedometer cable at the engine. It's held in by a wire clip. You can force it out with a screwdriver through the loop. Save it! Then gently pull the end of the cable out. You have to reach way down to get to it and let your eyes adjust to the shadows. Make sure the engine is cooled down if you drove it beforehand. Now pulling the cluster should pull the cable through the firewall enough to reach the bulbs. A half twist will release a bulb so you can inspect each one. Lamp # for my '93 Escort was PC194.

    To put everything back, put the cluster back into position and pull on the speedometer cable from the firewall side. I used long pliers. Once enough was pulled back through, pressure on the cluster made the rest go through, but at first there is too much cable to do that which is why you pull from the engine compartment. Put the end of the speedometer cable back. The wire clip is supposed to go through a pair of holes on both sides of the cable, but at this point it is all bent out of shape. You could buy a new one, but I straightened the old one with pliers. Feeding both pairs of holes is a pain. You can cut the clip in half and do each side separately, but I did just one side and called it good. You need to bend over the wire end that sticks through to make it stay. That was ******* the thumb - I could have used needle nose pliers.

    Put the screws back in the cluster, put back the dash and screws to hold it, and pull up the steering wheel and torque the bolts back in. It took me about 5 hours the first time because I had to figure things out. Now that I've done it once, it would be a 1 1/2 to 2 hour job to do it again. I had two bulbs burnt out and bought four replacements, two for the cluster and two spares kept in the glove compartment.

    Jul 16, 2008 | 1993 Ford Escort 4 Door

    1 Answer

    Wipers


    theres a little tab where the wipers connect to the wiper gear push this down and it should release. sometimes you got to really play with it

    Jul 10, 2008 | 1992 Oldsmobile 88

    Not finding what you are looking for?
    2000 Toyota Corolla Logo

    99 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    Marvin
    Marvin

    Level 3 Expert

    85108 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...