2004 Land Rover Discovery Logo
francis uteg Posted on Aug 30, 2012

How to adjust discovery headlights

How are the high and low headlight beams adjusted in a 2004 land rover discovery?

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 2 Answers
  • Posted on Nov 15, 2012
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Dec 06, 2009
Answers
2
Questions
0
Helped
4331
Points
2

Call or text 7328568836 and i will walk u through it

5 Related Answers

Jonah Oneal

  • 14092 Answers
  • Posted on Sep 16, 2009

SOURCE: how to program a keyless entry for land rover

MOST OF THE TIME WHEN YOU HAVE PROBLEMS IN THE REMOTE AND KEYLESS ENTRY.THE DEALERSHIP HAS TO REPROGRAM IT.BUT FIRST CHECK ALL THE FUSES AND RELAYS.IF THEY ARE OKAY.THEN DEALERSHIP HAS TO FIX.

Testimonial: "very good feedback."

Ad

Anonymous

  • 275 Answers
  • Posted on Sep 11, 2009

SOURCE: 2004 land rover discovery, ignition

it sounds like your starter motor is faulty. first make sure the battery is fully charged, then place a screwdriver between the contacts of the solenoid on the starter motor, if it again just clicks, then you need to repair or replace the starter motor.
hope this helps

Anonymous

  • 149 Answers
  • Posted on Feb 24, 2010

SOURCE: how to adjust rocker shaft on discovery td5

There are adjustment screws on the rockets according to RAVE.
The procedure is as follows:
1) Rotate the engine clockwise until No 1 injector lobe is at full lift.
2) Rotate rocker adjusting screw clockwise until the injector plunger is felt to bottom out.
3) Rotate rocket adjusting screw anti-clockwise one complete turn to give plunger the required bump clearance and tighten rocker arm adjusting screw locknut to 16Nm. Ensure the screw does not turn as the locknut is tightened.
4) Carry out the procedure for the remaining 4 rocker arms.
5) After completion of rocker arm adjustment slowly rotate engine clockwise 2 complete turns by hand to ensure that no injectors are bottoming out on their plungers.

Anonymous

  • 149 Answers
  • Posted on Feb 25, 2010

SOURCE: transfer case oil change- 1999 Land Rover Discovery II

No need for a diagram, to drain the oil, there's a drain plug on the bottom of the transfer box, under the handbrake drum. To fill, the fill plug is about in line with the centre of the handbrake drum and to the left. I think both plugs are 1/2" square. Fill to overflow with Texaco Multi-Gear 75W/90R. Takes about 2L or so.

Anonymous

  • 1 Answer
  • Posted on Apr 12, 2010

SOURCE: WHERE IS THE FUEL FILTER LOCATED ON LAND ROVER DISCOVERY 2000

LAND ROVER DISCOVERY II DONT HAVE FUEL FILTER, ONLY HAVE PRE FILTER IN THE FUEL PUMP

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Headlight relay for land rover discovery 1

Have you considered the bulbs in both the headlamp and the high beam indicator have both blown?

If you remove and check the headlight bulb first this may help resolve the problem.
0helpful
1answer

How do i adjust my headlights in my 2004 vovlo xc70

If you look just behind the headlight glass from the top, you will see two holes with 7mm hex head screws. These will adjust your headlights up, down, left and right.
0helpful
1answer

Low beam headlight stays on permantly

Could be that the low beam relay is stuck. If you can locate the relay usually in a fuse box in engine compartment ,remove it and see if lights go out.
11helpful
1answer

How do you adjust the headlights on a 2004 endeavor

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
12helpful
1answer

How do I adjust headlights on 2004 Intrepid

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
5helpful
1answer

Adjusting headlights on my 2004 ford taurs

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
7helpful
2answers

Headlamps need adjustmentthey shine to close to the car even when on high beeam

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
8helpful
1answer

Adjusting a headlight on a 04 discovery11 how too

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
8helpful
2answers

I have a 1998 landrover freelander how do i adjust the headlights ?

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
2helpful
1answer

Headlights

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.
Not finding what you are looking for?

698 views

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...