Question about 1996 Ford Crown Victoria

1 Answer

Can I use castrol for transmisson for 1997 ford crown victoria

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 21 Answers

As long as it carries the acceptable Mercon rating.

Posted on Aug 27, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: 1997 ford crown victoria starting problems

Sounds like you're on the right track. A bad TPS and ISC motor sensor will cause the problems you're experiencing. Your ECM relies on the readings it gets from the TPS to be sure there is enough air getting to the engine. If the ECM gets a bad reading and thinks not enough air is getting to the engine, it will cut the fuel supply, hence causing your engine to die. Your ISC relies on the reading from the TPS as well. It detects from the ECM if the throttle plate is closed or not. If it thinks the throttle plate is fully closed, it will start allowing air to enter the engine and bypass the throttle plate. If your ECM starts seeing some unmeasured air coming from ISC and detects the throttle plate is open (which it may not be due to a bad TPS reading), the ECM will again cut the fuel supply to avoid the risk of detonation.

So, replace your TPS first and see if that cures your problem. Also, check the resistence readings of your ISC to be sure that is within spec. If your problem still occurs, check your Intake Air Temperature (IAT) sensor in your air filter housing. Be sure your spark plugs, plug wires, and distributor are all in good shape as well. Replace your fuel filter if you haven't done so in the past 2-3 years.
Good luck!

Posted on Jun 23, 2008

  • 4387 Answers

SOURCE: 1998 ford crown victoria fuse box diagram

it should be in your owner manual. if not, I can look up something for you but can't post illustrations to this site.

Posted on Jan 09, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

mindreader
  • 578 Answers

SOURCE: I need the fuse diagram for a 2001 crown victoria

go to
http://www.motorcraftservice.com/pubs/content/~WO1CRO/~MUS~LEN/41/01croog4e.pdf
and check out pages 156 - 161. They provide all you have asked for!

Posted on Oct 11, 2009

  • 104 Answers

SOURCE: 2003 Ford Crown Victoria misfires when

I HAVE HAD THE SAME PROBLEM ON SEVERAL CROWN VICS I HAVE WORKED ON ,& SOME OF THEM A SET OF PLUGS STOPPED IT,AND SOME OF THEM HAD TO HAVE 1 OR MORE COIL PACKS REPLACED, BUT THE PROBLEM THAT I FOUND THAT IF PLUGS & ALL COIL PACKS HAD BEEN REPLACED,AND IT WAS STILL IN THE IGNITION, IS THE WIRES GOING INTO THE PLUG ON THE COILPACK UNDER THE INTAKE TUBE, IF YOU REMOVE THE INTAKE TUBE,LOOK CLOSE AT THE WIRES FOR ANY BARE SPOTS,& LOOK AT THE BOTTOM OF THE INTAKR TUBE IF YOU CAN SEE WHERE IT HAS RUBBED IT,IT IS ALMOST A GIVEN THERE IS A BARE SPOT OR CRACKED INSOLATION ON THE WIRE, ENOUGH TO CAUSE A MISFIRE, (FYI) IT TOOK ME MANY TIMES OF INSPECTING BEFORE I LOOKED CLOSE ENOUGH TO SEE THE BARE SPOTS, BUT ALL YOU HAVE TO DO IS STRIP THE HARD PLASTIC AROUND THE WIRES BACK ENOUGH TILL YOU SEE GOOD CLEAN LOOKING WIRE,THEN SEPERATE THE WIRES AND IF YOU HAVE LIQUID ELECTICAL TAPE USE THAT AND THEN TAPE THEM WITH ROLL ELECTRICAL TAPE ,BUT IF YOU TAPE THEM UP GOOD SO WHEN THE WIRE IS BENT ENOUGH FOR THE INTAKE TUBE TO CLEAR ,& YOU CANNOT SEE THE WIRES GOING IN TO THE PLUG WITH A ROLL OF ELECTRICAL TAPE THAT WILL WORK TOO, I HOPE THIS TRICK WILL WORK AS GOOD FOR YOU AS HAS ME ON DOZENS OF CROWN VICS, ESPECIALLY P71 POLICE CARS.

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 V8 4.6l. It turns over, but why won't it start?


Part 1 -How to Test the Starter Motor (Ford 4.6L, 5.4L)

troubleshootmyvehicle.com > Ford > 4.6L, 5.4L
Mar 2, 2011 - Page 1 of 3: How to test a BAD Starter (Ford 4.6L and 5.4L Pick Up and SUV). ... a BAD starter motor on your 4.6L or 5.4L V8 equipped car, pick up or SUV. ...and will turn over the engine; -OR-; The starter motor won't do a thing. ... Crown Victoria ... 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005.

Question: 1997 Crown Victoria Lx Cant Turn on and Cant ...

www.2carpros.com/.../question-1997-crown-victoria-lx-cant-turn-on-an...
May 26, 2014 - Ok so i put the keys in the car turn the key but seems to me it moves more ... 1997 Ford Crown Victoria • 4.6L V8 RWD Automatic • 99,625 miles ... Keywon't turn off accessories or turn car over and ignition cylinder turns too ...

Oct 19, 2015 | Ford Crown Victoria Cars & Trucks

2 Answers

What type of transmisson oil do I use for a 1996 ford crown victoria and oil filter


The fluid you need is called mercon type ATF this is what ford recommends to use and should say it on the bottle. as for a filter for the transmission or engine I recommend motorcraft filters they meet ford specifications and are available at most auto parts stores.

Mar 04, 2011 | 1996 Ford Crown Victoria

1 Answer

What type of transmisson oil do I use for a 1996 ford crown victoria


Should say on the dipstick but Mercon/dexron transmission fluid is what you need.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Oct 02, 2010 | 1996 Ford Crown Victoria

1 Answer

Where is the location of no. of cylinder on crown


2004 Ford Crown Victoria 4.6 liter V-8 VIN "W"

a39c7f2.gif

Hope helps (remember rated this).

Jul 19, 2010 | 1997 Ford Crown Victoria

1 Answer

1997 Crown Victoria: 92 crown victoria get no spark...


Attempt to change all of the spark plug wiring and spark plugs. Then start the vehicle.

May 18, 2010 | 1997 Ford Crown Victoria

1 Answer

I have a 1997 Ford Crown Victoria. In cool


sounds like the fuel pump is going out. next time it won't start have the fuel pressure tested or spray starting fluid into the air intake to see if it starts.

Apr 01, 2010 | 1997 Ford Crown Victoria

1 Answer

1997 ford crown victoria window reulator and motor replacement steps


easy real easy.. go out to the local pull a part junk yard.. get a cross ref on your car.. find that car in the yard and tear it apart in the yard so that you can then later be able to do the same thing in your on ride.. all you need for tools is a walmart 30 piece set your good to go.

I’m happy to help further over the phone at https://www.6ya.com/expert/dennis_7c5f8bf265aab5e9

Oct 18, 2008 | 1997 Ford Crown Victoria

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85161 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...