How t o replace 1998 chevy malibu v6 engine power steering hoses and pump?

SOURCE: 1987 Chevy G20 van replace power steering pump

Does your van have the serpentine belt? If so maybe I can help, I replaced the Power steering pump on my 90 G20 a couple of weeks ago. The trick is that you need to pull the pump pulley which is pressed on to access the mounting bolts which attach the pump to the engine. Harbor Freight tools sells a great tool designed for this job for $20.00. Once you have the correct tools, remove the serpentine drive belt. You may also need to remove the fan shroud. the pump shaft looks like it has an allen socket in the center, but this is for use in the manufacturing process, and will not come out. Place the puller tool on the pulley following tthe instruction that come with the tool, and remove the pulley. loosen, but do not remove the nut on the high pressure hose connection. use a pair of **** pliers to cut and remove the crimp clamp on the low pressure hose. If your pump has the remote reservour loosen the clamp on the reservour hose also. Remove the three mounting bolts, place a large pan under the pump to catch drips, and remove the prevously loosened hoses. there will be fluid leaking all over and the pump should come free, There are two types of replacement pump sold. With and without reservour. This reservour is a metal cover that fits over the back of the pump, and should not be confused with the reomte revervour found on some newer models which is next to the battery. This reservour is held in place be two throught the pump bolts which are removed at the back of the pump. If your new pump has a reservour you will probably still need to remove these bolts and put them in the replacement pump as most are shiped without these bolts. If you replacement pump comes without a reservour pull the bolts, the reservour should pull off of the old pump and slide onto the new one. check the o rings and replace the through the pump bolts. Installation is the reverse of removal execpt that 1/2" hose clamps replace the crimp clamps on the low pressure hose, and the puller tool is set up differently to replace the pulley. Finally if you don't flush contaminants out of the system your repair will last maybe a week. www.cardone.com has a great article about power steering flushing, read it before you start Good luck.

SOURCE: power steering - 1999 chevy silverado

You're going to have to bleed the system alot on those trucks. Just remove the return line and have an assistant turn the steering wheel back and forth just enough to engage the pump and filling the resevour while doing this. Keep bleeding until you have a good flow of P/S fluid out with no air bubbles. This can take a while.

SOURCE: replaced power steering hose 1500 chevy pickup

Maybe got an air lock/bubble

SOURCE: how to replace valve cover gasket 1998 chevy malibu

The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced. 

SOURCE: replacing the power steering pump on a 1998 isuzu rodeo

Remove low pressure and high pressure hoses (this one could be hard to break loose). You might want to have an oil pan handy, to capture the oil. Disconnect electrical sensor. Remove the bolt that holds belt tension adjustment plate. And finally remove the bolt that holds the pump in place. It is bolted from the back and located at the right lower corner of the pump if you are facing the front of the car. Remove the pump assy. I could not remove belt pulley at home, no matter how hard I tried. Ended up taking it to an automotive shop and they removed it in no time, using one of those "pneumatic impact guns". Assemble new pump. Fill the reservoir with PS oil. Make sure both of the front wheels are off the ground, start the engine and slowly spin the steering wheel back and forth for about 5 minutes or untill screeching sound stops and the liquid in the reservoir stops foaming. That will bleed any air that is in the system. Don't go all the way to the end of stroke. Good luck.