Inner door panel removal

Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

If it's loose from the door, you need to remove the inner door panel to access the screws that hold the mirror in place on the door itself. To remove the inner door panel may simply involve removing some screws, but some models require a special upholstery tool to loosen the panel fron the clips. Once the panel is loose, tighten the mirror and replace the inner panel. Be cautious with door switch wiring!

cable? (electric>?)
here is the page on motor;reg.

1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
   • Remove door trim panel.
   • Remove isolator.
   • Remove front door glass.
   • Loosen bolts attaching regulator to inner door panel.
   • Remove bolt attaching regulator to inner door panel.
   • • Lift regulator upward to disengage bolts from door inner panel.
     • Disengage power window regulator harness connector, if equipped.
     • Remove regulator through access hole in door
   • Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
   • Remove the power window motor from the window regulator.

REMOVAL

1. Remove the watershield. (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD - REMOVAL)

2. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent(FRONT DOOR GLASS CLIPS).

3. Disconnect wire connector from power window motor, if equipped.

4. Loosen screws attaching front and rear window guide rails to inner door panel (FRONT DOOR MANUAL WINDOW REGULATOR - TYPICAL).

5. Remove screw heads on guide rails from key hole slots in inner door panel.

6. Loosen screws attaching regulator to inner door panel.

7. Remove regulator from inner door panel.

8. Extract rear guide rail through inner door panel rear access hole (FRONT DOOR POWER WINDOW - TYPICAL).

9. Extract front guide rail through front access hole.

INSTALLATION

1. Insert front guide rail through front access hole.

2. Insert rear guide rail through rear access hole.

3. Place window regulator in position on inner door panel.

4. Place screw heads on guide rails in position through key hole slots in inner door panel.

5. Tighten screws to attach front and rear guide rails to inner door panel.

6. Connect wire connector into power window motor, if equipped.

7. Install door glass.

8. Verify door glass alignment and operation.

9. Install sound shield and door trim panel

DIAGRAMS CAN BE FOUND ON JUSTANSWER,COM

Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

Door Panel

1. Remove the retaining screws from the armrest assembly.
   
2. Remove the screws retaining the switches to the housing and remove the cover assembly.
   
3. Remove the door trim panel retaining screws.
   
4. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.
   
5. Disconnect all the wiring, if so equipped, and remove the trim panel.
   

To install:

1. Position the trim panel to the door inner panel and connect the wiring, if so equipped.
   
2. Push the trim panel and retaining clips into the inner door panel holes and install the retaining screws. Install the screws retaining the switches to the housing.
   
3. Position the armrest to the trim panel, and install the retaining screws.
   

PLEASE DON'T FORGET TO RATE!!

Door Panel

1. Remove the door handles and the locking knob from the inside of the doors.
   

If equipped with screw retained door pull handles, remove the screws through the handle into the door inner panel.

1. If equipped with remote control mirrors, remove the remote mirror escutcheon, then disengage the end of the mirror control cable from the escutcheon.
   

Door lock remote control handle


Removing the clip from inside the door handle

3. If equipped with a switch cover plate in the door armrest, remove the cover plate screws, then disconnect the switches and the cigar lighter (if equipped) from the electrical harness.
4. If equipped with an integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. If equipped with an armrest applied after the door trim installation, remove the armrest-to-inner panel screws.


View of the armrest switch cover plate and remove mirror cable attachment

1. If equipped with two-piece trim panels, disengage the retainer clips from the front and the rear of the upper trim panel, using tool No. BT-7323A, then lift the upper door trim and slide it slightly rearward to disengage it from the door inner panel at the beltline.
   

If equipped with electric switches in the door trim panel, disengage the electrical connectors from the switch assembly.

1. Along the upper edge of the lower trim panel, remove the mounting screws. At the lower edge of the panel, insert tool No. BT-7323A between the inner panel and the trim panel, then disengage the retaining clips from around the outer perimeter. To remove the lower panel, push the panel down and outward to disengage it from the door.
   

If equipped with courtesy lights, disconnect the wiring harness.

1. If equipped with an insulator pad glued to the door inner panel, remove the pad (with a putty knife) by separating it from the inner panel.
   

To install:
If replacing the inner pad to the door inner panel, use 3M General Trim Adhesive No. 8080, glue it to the panel.

1. If removed, glue a new inner pad to the door inner panel.
   

If equipped with courtesy lights, connect the wiring harness.


Exploded view of the window regulator handle


Exploded view of the door trim panel

1. Engage the retaining clips around the edge of the lower trim panel, then install mounting screws.
   

If equipped with electric switches in the door trim panel, engage the electrical connectors to the switch assembly.

1. If equipped with two-piece trim panels, engage the retainer clips to the front and the rear of the upper trim panel.
   
2. If equipped with an integral armrest, install the retaining screws.
   
3. If equipped with a switch cover plate in the door armrest, engage the switches and cigar lighter (if equipped) harness connectors, then install the cover plate and secure using the plate screws.
   
4. If equipped with remote control mirrors, engage the control cable, then install the remote mirror escutcheon.
   

If equipped, install the pull handle screws through the handle into the door inner panel.

1. Install the door handles and the locking knob to the inside of the doors.
   

Exploded view of the 2-piece door trim

1. Remove the door handles and the locking knob from the inside of the doors.
   

If equipped with screw retained door pull handles, remove the screws through the handle into the door inner panel.

1. If equipped with a switch cover plate in the door armrest, remove the cover plate screws, then disconnect the switch
   

from the electrical harness.

1. If equipped with an integral armrest, remove the screws inserted through the pull cup into the armrest hanger support. If equipped with an armrest applied after the door trim installation, remove the armrest-to-inner panel screws.
   
2. If equipped with two-piece trim panels, disengage the retainer clips from the front and the rear of the upper trim panel, using tool No. BT-7323A, then lift the upper door trim and slide it slightly rearward to disengage it from the door inner panel at the beltline.
   

If equipped with electric switches in the door trim panel, disengage the electrical connectors from the switch assembly.

1. Along the upper edge of the lower trim panel, remove the mounting screws. At the lower edge of the panel, insert tool No. BT-7323A between the inner panel and the trim panel, then disengage the retaining clips from around the outer perimeter. To remove the lower panel, push the panel down and outward to disengage it from the door.
   

If equipped with courtesy lights, disconnect the wiring harness.

1. If equipped with an insulator pad glued to the door inner panel, remove the pad (with a putty knife) by separating it from the inner panel.
   

To install:
If replacing the inner pad to the door inner panel, use 3M General Trim Adhesive No. 8080, glue it to the panel.

1. If removed, glue a new inner pad to the door inner panel.
   

If equipped with courtesy lights, connect the wiring harness.

1. Engage the retaining clips around the edge of the lower trim panel, then install mounting screws.
   

If equipped with electric switches in the door trim panel, engage the electrical connectors to the switch assembly.

1. If equipped with two-piece trim panels, engage the retainer clips to the front and the rear of the upper trim panel.
   
2. If equipped with an integral armrest, install the retaining screws.
   
3. If equipped with a switch cover plate in the door armrest, engage the switch harness connector, then install the cover plate and secure using the plate screws.
   

If equipped, install the pull handle screws through the handle into the door inner panel.

1. Install the door handles and the locking knob to the inside of the doors.
   

Front Door

1. Remove the door trim panel.
   
2. Remove the water dam.
   
3. Remove the inner and outer door belt weatherstrips.
   
4. Lower the window to the full down position and align the glass regulator arm with the access holes in the inner door panel.
   
5. Remove the front glass run channel.
   
6. Remove the nuts attaching the glass channel to regulator arm.
   
7. Separate the glass and lift it up and out.
   
8. Disengage the power window motor wire connector from the door harness, if equipped.
   
9. Loosen the bolts in slotted holes attaching regulator to door inner panel.
   
10. Remove the bolts attaching window regulator to inner door panel.
    
11. Remove the regulator through the access hole in the inner door panel.
    
12. Installation is the reverse of removal. Tighten the nuts attaching the glass to the lift plate to 7 ft. lbs. (9 Nm).
    

Power window regulator mounting—Dakota, Durango


Window regulator removal—Dakota, Durango

Posting more on next post for door panel removal and installation.

Not that difficult of a task, it would be wise to get a service manual with step by step instructions and pictures. Factory ones are here for $20 bucks http://www.promanuals.net/dodgejeep.html

Trim
(1) Remove trim plug from mirror flag bezel.
(2) Remove screws attaching trim panel to door
(3) Using trim remover detach trim panel perimeter push-in fasteners from
door inner panel.
(4) Lift trim panel upward and separate from door.
(5) If equipped, disconnect harness connectors for
power accessories.
(6) Disconnect latch rods from inside handle actuator.
(7) Separate trim panel from vehicle.

Window Regulator
(1) Remove front door glass, (you may be able to access the regulator if the window is up)
(2) Loosen bolts attaching regulator to inner door
panel
(3) Remove bolt attaching regulator to inner door
panel
(4) Lift regulator upward to disengage bolts from
door inner panel.
(5) Disengage power window regulator harness
connector, if equipped.
(6) Remove regulator through access hole in door.

Window Regulator, Rear Door, Explorer Removal

1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .

Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation

1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.

1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.

1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.

1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .

1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .

1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.

1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
   
   

1. If equipped with power windows, disconnect the wire from the regulator.

1. Remove the rear door window glass as described in this section.

1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.

1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
   

1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.

1. Remove two upper regulator attaching nuts.

1. Remove regulator from the front door (20125) .

Installation

1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.

1. Install regulator into access hole in inner panel.

1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).

1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).

1. Install two upper regulator attachment nuts.

1. Install door glass as outlined under Door Glass Installation.

1. Adjust glass as outlined under Adjustments .

1. Reconnect wire to regulator, if equipped.

1. Check operation of window regulator.

1. Install door watershield and trim panel. Refer to Section 01-05B .