1997 mazda rustler 160i wheel bearings

This is a hydraulic lifter engine, no adjustment is needed.

This engine used hydraulic cam follower. no adjustment. See link below. https://www.mazdabg.com/ftp-uploads/Mazda/323/AdjustmentData/MAZDA32316iB6.pdf

If you are mechanically inclined, start by having a multimeter connected to your battery. Then, remove fuses one at a time while checking if the draw goes away. This will isolate the circuit and then you begin checking components within that circuit.

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Hi u will need a intake manifold and a carb .it will cost u about R3400 but Y do u want to put a carb on a fuel injected car

An ignition coil is more than likely your problem. When the car is not running pull one spark plug wire and a plug and insert plug into the wire hold plug end on ground area. Have someone crank engine and check for spark. If no spark, replace ignition coil.

faulty fuel pump

REMOVAL & INSTALLATION Except Miata FRONT

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   • Steering knuckle from the vehicle
   • Inner oil seal from the knuckle
3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
4. Remove or disconnect the following:
   • Bearing inner race from the front wheel hub
   • Retaining ring from within the knuckle
   • Front wheel bearing from the knuckle, using the hub puller tools
   • Brake dust shield
5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
   
6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
7. Using the press tools, press a new wheel bearing into the knuckle assembly.
8. Install or connect the following:
   • Wheel bearing retaining ring
   • New oil seal using Installation tool 49 V001 795
   • Front wheel hub using the Mazda press tools

REAR

1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
   
2. Remove or disconnect the following:
   • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar)
     
     
   • Brake drum, if equipped
   • Rear caliper and rotor assembly from the hub, if equipped
   • Hub dust cover
3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
4. Remove or disconnect the following:
   • Hub retaining nut and discard it
   • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle
     
   To install:
   
5. Install or connect the following:
   • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
   • Stake the nut into the groove in the spindle
   • Dust cover
   • Assemble the brakes
   • Rear wheel

a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Hi Gerrie1974-

WildBill49 here......Not knowing the specific year and version of your Mazda, I cannot give you a specific part at fault, but I can help you. I am assuming we're talking about an electronic distributor single coil ignition system

If the spark is weak directly out of the coil (with a known good coil hooked up with correect polarity), then the problem is in the spark trigger module... There is a variety of designs, but the basic components remain the same. This is the part of the ignition system that replaces the breaker points. It consists of two parts - a magnetic spark trigger sensor, and a spark signal amplifier/controller. these are sometimes combined into one ignition module.

Replace this module, and spark from the coil should be strong! If it is still weak, reverse the two wires to the coil.

Weak spark at the plug wire with the above good indicates distributor cap/rotor replacement time...

Gerrie, I hope this is what you are looking for, best of luck, and if you feel my advice worthy, please rate it!!!

Thanx-
-WB