2007 Chevrolet Chevrolet Equinox LT Logo

Related Topics:

vincent waitt
vincent waitt Posted on Aug 09, 2012
Be the first to answer

2007 chevy equinox code p0962

Code p0962 ,need diag precedures and connector pin out for tcm to trans 22 pin connector "c2"

Answer This Question

5 Related Answers

Jonah Oneal

  • 14092 Answers
  • Posted on May 16, 2009

SOURCE: Lost power on drivers side door 2007 chevy equinox

check fuse .if fuse good you got a bad ground.

Ad

Anonymous

  • 3640 Answers
  • Posted on Feb 20, 2010

SOURCE: dtc code p0121 and p2135 2007 chevy malibu

both codes refer to the throttle position sensor, the sensor is at the throttle plate, on the side of the throttle body. to test remove the connector to sensor, use a ohms meter to test. put 1 lead to top connection and the other to the bottom one. move throttle and the needles on the ohms meter should move very even, move throttle slow to get a good reading, needle should move without no hesitation, if the test is bad replace tps sensor. if the sensor gets to bad, it can have an effect on transmission shifting. after fixing sensor have the light turned of with an obd2 scanner.

Anonymous

  • 91 Answers
  • Posted on Feb 23, 2010

SOURCE: I have a 2007 Chevy Equinox needing a transmission flush

It is best to flush the fluid this gets the fluid out of the torque converter.This transmission uses special fluid tpye t-Iv gm # 88900925 do not use dexron fluid in this transmission.

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Sep 28, 2010

SOURCE: 2007 chevy equinox codes p0700 &p0705. van

P0700 Transmission Control System Malfunction, this comes on anytime a problem is sensed in the transmission
P0705 Transmission Range Sensor Circuit malfunction(PRNDL Input)
this means that the circuit that signals the transmission control module when u slect a gear (Drive reverse etc.) has a problem, this can be the range selector switch or the wiring connector or the control module, in order to pin down which part is causing the fault code the Chevy dealer must hook up a scan tool called a "Tech II" and read the transmission data as the different gear requests are made.

alicantecoli

Colin Stickland

  • 22516 Answers
  • Posted on May 25, 2011

SOURCE: i have chevy equinox 2007 AWD LT , i sccaned

you can reads a code ?? this is a result as the europeon model of this vehicle which has a OBDII is all encrypted software and iam extremely jealous .Sorry but this code number doesnt show in my list of manufacturers codes or the generic code chart

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a 2007 Chevy equinox that will not start, the diagnostic reads no communication with the ECM, what does this mean and how do i fix it?
Go under the hood in the main fuse and relay box and check the fuse for the ECM. Also check Pin number 16 on the diagnmostic connector under the dadsh where the code reader plug in. it shoud show 12 volts with the key on. See picture of the connector pins below.
obd2 diagnostic port-l30rktph4ccflrpmcgx34yof-1-0.jpg
Read full answer
Feb 16, 2017 • Cars & Trucks
2helpful
2answers

98 jeep grand cherokee check engine lite code torque converter clutch solenoid circuit how hard is it to fix?
Could be bad may you have to rebuilt it.
Read full answer
Oct 16, 2016 • 1998 Jeep Grand Cherokee
1helpful
1answer

TCM not working trans is in satety mode have to shift manualley
the TCM , just like the ECU has flash codes

you insert a diag, jumper wire to the DLC and red the fash

codes, say code XXXX tail speed sensor dead.

the 4L30E trans? same as trooper and that fact can help find info.



this is true for all TCM made , all

on new cars uSA 1996 + the PCM reports, TCM errors.

why not login in to alldata.com and see these simple steps.

why guess? for $15 bucks, amazes me....???



94 Rodeo

finding old rodeo TCM facts is like pulling teeth, (very few run now)



DLC conn

jump pins 1 and 3 for TCM

this is trooper hope is same

http://www.2carpros.com/forum/automotive_pictures/248015_Picture1_11.jpg



3 pin DLC conn

1 and 2 is ECU flahs

1 and 3 is TCM. 1 is ground.

jumper it.

see lamp flash the code.

the 2 pin connector is for the Tech1 scan tool no one has now.



had to find.

code: (keep in mind many codes see LIMP mode, skips gears.)

16 is oil temp failure.



google works with 4L30E, and isuzu.

http://www.motor-talk.de/forum/aktion/Attachment.html?attachmentId=699188

see that.

see page 237 , it even shows the trooper connectors.

and the flash codes.

but you must figure out type 1 or 2.

only

ah it say type 2 is yours.

so now you have a full DTC error map for your car.

and all it cost is a paper clip
Read full answer
Aug 02, 2014 • 1994 Isuzu Rodeo
0helpful
1answer

How many plugs have the tcm have on a jeep cherokee 3.7 auto
its really a grand cherokee.!
TCM tranny puter.'
NAG1 (early and late) or 545RFE trans? there are 3.
i guess, you are trying to find it......
first off, go to alldata.com and look.
and all cars move the TCM , into the PCM , from 1997 to 2004 (aprox)
but this jeep 07

nag1 MTC, (module trans control) has C1 and C2,
RFE has. C4, 10 pages, on RFE and all show, C4 only.
not sure what that means.?

the TCM/MTC is not integrated in to the PCM. yet. on this year.
there are 2 modules on the RFE,
i highly recommend a real FSM.
or alldata.com
Read full answer
Nov 07, 2013 • Jeep Cars & Trucks
0helpful
1answer

Where is the tcm and pcm on a 08 chevy equinox
under the fuse box under the hood.
Read full answer
Mar 17, 2013 • 2007 Chevrolet Equinox LS New Cars
0helpful
2answers

Auto Trans 4l30-E Slips in 2nd and 3rd gear
its repair manual

PDF]GENERAL MOTORS Hydra-Matic 4L30-E automatic transmission

scottj.info/files/isuzu/4l30e.pd
code 22 tps can either be set in volts or non replaceable
code 53 is fault in transmission control module

code 51 is a issue ( note particular vehicle configuration.)
http://repairpal.com/gm-obd-code-51

replacement transmission and its ECU should be fitted and matched together
or a diagnostic scanner used to reconfigure the modules

did you actually test drive the replacement transmission
before fitting to the truck
Read full answer
Mar 06, 2017 • Isuzu Cars & Trucks
0helpful
1answer

Shifts hard into third, codes come up shift solenoid B malfunction, dealer says it's a wiring prob. Where/how to start?
All I can say is to take it to a trans shop or the dealer, you will not be able to diag and fix this problem yourself it is a detailed pinpoint test that involves specific tools. Replacing the solenoid assembly it turned out to be a TCM (Transmission Control Module)... may not be the cure for your demon but its a possibility.

It could be a not completely seated connector, bad solenoid or a bad molded lead frame (shift solenoid complete assembly) or a new unit.

Check this procedure: Diagnostics/Automatic%20Transmission/Circuit%20Inspection/cip0750p.

Keep us updated.
Read full answer
Mar 13, 2011 • 2007 Nissan Sentra 2.0 SL Sedan
0helpful
1answer

Dodge 2007 ram 1500 5.7v8 ....need wiring diagrams for trans and ecm/tcm also connector views with wiring colors and pin numbers and locations vin is:1d7hai8237j552470
autozone or O'relly's carries books Chiltion or Haynes in the back of the book it has electrial diagrams it is NOT in color, However it labels the wires and states each color.
Read full answer
Dec 06, 2010 • 2007 Dodge Ram Truck
0helpful
1answer

Hi ! I have a 2006 Chevy Equinox, I lose power to trans untill the truck barely wants to move after 2bks or so. p0700 / p0705 are the codes that have come up. We replaced the tcm (p0700). p0705 comes up...
Since this vehicle does have a possible reprogramming issue, before I spent any money on parts, let them hook their scanner(in this case it going to be the tech 2 with downloadable info from a mainframe to reprogram) and see if there are any other under lying codes or info. What this means is that they have the ability to read and interpret live data to pin point the issue. the code may be merely a reference point. There may also be a TSB regarding this issue. Start at the dealer, then work on replacement of parts. Always start with information first. Sometimes we are suprised by what we find. Let me know what they say and if you need anything else.
Read full answer
Aug 25, 2010 • Chevrolet Equinox Cars & Trucks
0helpful
2answers

2002 Dodge Caravan with approx. 66,000 miles, check engine light came on, seemed to have stayed in 2nd gear. Could it be a pac solenoid transmission problem?
You need to find someone who can pull the codes from the transmission and see what kind of trans fault it is. If there is a fault in the trans the controller will put it into limp in mode which is 2nd gear locked. Won't shift out of 2nd...You need to pull the codes and see if it is internal in the trans or an external sensor-Good Luck
Read full answer
Oct 13, 2009 • 2002 Dodge Caravan
Not finding what you are looking for?

View Most Popular

2007 Chevrolet Equinox LT

  • Cars & Trucks

Related Question

I have a 2007 Chevy equinox that will not start, the diagnostic reads no communication with the ECM, what does this mean and how do i fix it?

  • Cars & Trucks

450 views

Ask a Question

Usually answered in minutes!

Popular Questions

4.3 Firing order diagram for 4.3L v6 Chevy engine

1999 Chevrolet K1500

What does my check engine light trouble code $7e8 mean?

2009 Chevrolet HHR 2.4

Transmission slips after engine warms up

Chevrolet Cavalier Cars & Trucks

When i press the ac button it blinks three times

2007 Chevrolet Tahoe

What causes high pressure in cooling system?

1993 Chevrolet Suburban

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...