Question about Chevrolet Tracker
Need to find location of the egr valve on a 2002 chevy tracker with a 2.5 engine
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
ha ha thats a fun one.. look on the drivers side of engine next to the firewall, behind the throttle body.
Posted on Jan 05, 2009
Take off your EGR valve and clean it out with carb cleaner also
grease tyhe little screw thing in it,,, u will c what i mean if u take it apart. carbon builds up in the chamber. it is located at the back left side of your engine and is a bit of a pain to take off. this should save u the cost except for the cleaner and labor. i had the same problem cheapest i found was 90$ on ebay.
Posted on Jan 17, 2009
The egr valve is located at the end of a hose that plugs into youe valve cover. It is pushed right into a rubber grommet that is located in one of the valve covers. I hope this helps. don.t forget to rate my nswer, thanks
Posted on Feb 27, 2009
SOURCE: egr valve location
The EGR Valve Location is typically housed on the intake manifold this schematic may help you
Posted on Mar 07, 2009
SOURCE: Location of EGR Valve
Found the info!!
This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!
Posted on Mar 14, 2009
Tips for a great answer:
Dec 17, 2015 | Cars & Trucks
Dec 15, 2014 | 2002 Chevrolet Silverado
Apr 16, 2014 | 2001 Jeep Cherokee
Nov 30, 2012 | 2002 Chevrolet Tracker
Jul 12, 2011 | 2001 Chevrolet Tracker
Feb 11, 2011 | 2002 Chevrolet Impala
May 25, 2010 | 2002 Chevrolet Malibu
Sep 19, 2009 | 1999 Chevrolet Tracker
Mar 07, 2009 | 1996 Geo Tracker 2 Door
1,516 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: