Question about 1996 Audi A6

Open Question

A6 c4 rear bumper removal

Remove rear bumper

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Removing rear bumper on Audi A4 1997 to fit tow bar

Did you get the solution to this, I have the same problem

Posted on Jul 14, 2008

Ad
  • 345 Answers

SOURCE: 1995 audi a6

two bolts through middle(allen key)they are about halfway along you will see them if you look underneath near edges of number plate.....

Posted on Oct 26, 2008

  • 6 Answers

SOURCE: 96 Audi A6 Front Bumper

No, they are not. THe A4 and the A6 chassis are different, the bumpers have a similar style and look to them, but they are not interchangable.

Posted on Jun 23, 2009

  • 10 Answers

SOURCE: how do i remove a rear bumper from a audi a4

If I remember correctly, you just push forward and pull the side out, just like the front bumper.

Posted on Sep 15, 2009

  • 26 Answers

SOURCE: How do I remove the rear light assembly on a 2008 A6 S-Line

Drill a tiny hole in the lense , where the water is gathering take lense piece out let dry ,fill hole with small amount of silicone rubber,clear,walmart has it in hardwear/paints .

Posted on May 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove bumper


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly.

2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle.
3. Install rear bumper in reverse order of removal.

Dec 22, 2013 | 2004 Kia Sedona

1 Answer

Locaton of horn


Should be up under the front bumper cover by the fog lights. Remove the front bumper skin to replace. Check youtube for videos of how to remove or a service manual. Requires removal of the headlights, under splash guard among other things.

Dec 06, 2013 | 2010 Audi A6

1 Answer

How to change a 1999 Audi a6 alternator


Changing the alternator itself is the easiest of tasks on the A6. It's getting to it that is a problem.
Here is how.
Disconnect the headlight connections the remove the headlamps.
Disconnect the water hoses between engine and radiator.
Remove transmission cooler pipes from radiator. (You have to plug these somehow to prevent loss of ATF and dirt contamination)
Remove spot light covers from bumper. Look under there and you will see 2 alled bolts fixing the bumper to the chassis. Undo these.
Next remove the bumper bolts on the fenders whichn yo can only reach through the headlight holes.
Ease out the grille and disconnect any wiring that could be strained especially the one on the radiator lower hose.
Pull the right side of tf the bumper out more to see the alternator. You do not have to remove air con pipes, just un-hook any hangers.
You need a 17mm socket and power bar to remove the serpentine belt then you undo the 2 bolts attaching alternator to motor and the 2 elecric cables to the alternator.

Jan 29, 2013 | 1999 Audi A6

2 Answers

How to remove rear bumper 1999 blazer


Hi there:
Check this Removal Procedure...

6_23_2012_11_21_59_pm.gif

1. Remove the rear bumper step pads.
2. Remove the license plate lamps.
3. Remove the nuts and the bolts that retain the rear bumper impact bar to the bumper bracket.
4. Remove the rear bumper impact bar from the vehicle.

Installation Procedure

6_23_2012_11_22_56_pm.gif

Notice: Refer to Fastener Notice in Service Precautions.

1. Install the rear bumper impact bar to the vehicle as follows:

1.1. Position the bumper impact bar on the bumper brackets so that the holes in the impact bar are aligned with the bracket holes.
1.2. Install 2 bolt plates and 4 nuts on top of the impact bar.
1.3. Install 2 bolt and nuts through the bottom of the impact bar. Tighten the rear bumper impact bar nuts to 90 N.m (66 lb ft).

2. Install the license plate lamps.
3. Install the rear bumper step pads.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 1999 Chevrolet Blazer

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?


take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.
  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Dec 27, 2010 | 2005 Hyundai Tucson

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

How to remove the rear bumper on a 2005 Kia Sedona


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Nov 09, 2009 | 2005 Kia Sedona

2 Answers

Head lamp bulb chance on audi a6 2005?


you need to remove the front bumer and you will see the head lamp bolts remove them and your headlamp unit is free as a bird.

Jul 18, 2009 | 2005 Audi A6

1 Answer

1995 audi a6


two bolts through middle(allen key)they are about halfway along you will see them if you look underneath near edges of number plate.....

Oct 26, 2008 | 2002 Audi A6

Not finding what you are looking for?
1996 Audi A6 Logo

Related Topics:

397 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...