Question about 2005 Chrysler Sebring Sedan
LOSES POWER AT 70MPH I HAVE TO SHUT OFF AND RESTART FOR IT TO CLEAR UP. HAD CODES PULLED AND P0315 P0300. IT HAS A 2.4L.
Well the code p0300 is a mis fire code the 315 is I believe a cam timing code which can cause the 300 replace the cam trimming actuator, it should fix ur problem.
Posted on Jul 29, 2012
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
FIRST YOU TURN IGNITION SWITCH ON WITH ENGINE OFF.LOOK AT MIL LIGHT IT SHOULD COME ON 3 SECONDS THEN GO OFF IT NOT THEN YOU GOT BURN OUT BULB OR A CIRCUIT PROBLEM.IF ALL IS WELL. ATTEMPT TO START ENGINE.TURN OFF IGNITION. WITH OUT STARTING ENGINE.TURN IGNITION ON OFF ON OFF AND WITHIN 5 SECONDS RECORD 2 DIGIT DIAGNOSTIC TROUBLE CODES.DISPLAYED BY FLASHING MIL LIGHT.YOUR MIL FLASHES WILL BE YOUR CODE LIKE THE MIL LIGHT FLASHES 5 TIMES THEN PAUSE FLASHES 3 TIMES THAT CODE 53 THAT YOUR CODE.IT LIKE MORSE CODE.WHEN DONE TURN OFF IGNITION SWITCH.GO TO AUTO ZONE OR ADVANCE AUTO GET HAYNES COMPUTER CODE BOOK. TO GET CODE MEANING OR WHAT SENSOR GONE BAD.HOPE THIS CAN BE SOME HELP.
Posted on Jul 27, 2009
PO442 means you have a small leak in your EVAP system. Most common cause is a bad gas cap, replace the gas cap with a factory gas cap,after market fail or does not conform to the OEM EVAP system. Other cause would be small leaks in the EVAP vacuum lines. P0445 is also related to the EVAP system and has detected a large leak in the system. Start with the gas cap as mentioned above. P1685 Is an issue with the ignition not recognizing the ignition keys and the car's ignition immobilizer my activate leaving the car not being able to start. That's going to have to be a Dealer repair. Good luck and hope this helps.
Posted on Jun 15, 2009
me too! - looking at fuse #5 red 10 Amp one but has black thing on it.
Can't get if off..
Have read the manual is wrong and to use panel on side of fuse box for fuse locations...
Posted on Jun 24, 2009
Battery is behind the tire. You have to remove the tire to get to the battery.
First of all you DO NOT have to remove the tire...you turn your wheels hard right, this will give you plenty of room to get to the battery. Remove the wheel well plate and you will see the battery just in from of where the tire would normally be pointing. From there it's pretty straight forward.
Posted on Dec 06, 2009
Tips for a great answer:
Jan 03, 2017 | Chrysler Cars & Trucks
Aug 15, 2016 | 2005 Chrysler Sebring LX
Sep 09, 2014 | 2005 Chrysler Sebring LX
May 18, 2014 | Cars & Trucks
Feb 12, 2018 | 2002 Chrysler Sebring
Feb 10, 2013 | 2005 Chrysler Sebring Sedan
Sep 09, 2017 | 1999 Chrysler Sebring
Sep 07, 2010 | 1999 Chrysler Sebring
Jan 02, 2010 | 2008 Chrysler Sebring Convertible
Sep 21, 2009 | Chrysler Sebring Cars & Trucks
394 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: