2005 Buick Lacross remote keyless entry partially operable

The Lock's lock from the door switches ? If they do it's not a fuse problem . Which of these does your vehicle have ?
Keyless Entry System Description and Operation (with Accessory 2 Way Remote)
Keyless Entry System Description and Operation (without Accessory 2 Way remote)

The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors/liftgate when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Vehicle locator/Panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Your best bet , take it to a GM dealer .

Testing would need to be done , scan tool hooked up checking DTC'S - diagnostic trouble codes . View data etc...
Keyless Entry System Description and Operation - Active
The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the door locks to unlock the vehicle. Keyless entry will lock/unlock a door or open the rear compartment lid when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message. A low transmitter battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas, such as gas stations that use pay-at-the-pump RF transponders, may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following features:
• Door lock/unlock
• Rear compartment lid release
• Illuminated entry lamps
• Panic alarm/Vehicle locator
• Remote vehicle start

Your best bet , take it to a qualified repair shop . Dealer

Is this an issue with all 2008 HHR remotes??? Highly doubtful , probably the vehicles keyless entry system . Taking the vehicle to a qualified repair shop an having the keyless entry system checked for DTC'S - diagnostic trouble code's . Do you know what a DTC is ?
The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors, or release the rear compartment lid when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Remote rear doors (Panel only)
• Vehicle locator/panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Guessing will not fix this .

it might only have keyless entry. that is all i have on my 2003 camry doors lock and unlock and lights flash but has no alarm. has panic on back of remote and trunk and open and lock on front of remote

RFA / MOD fuse 10amp . location - insturment panel fuse box. Fuse Block - I/P
Right side of the I/P, behind the access panel
If the fuse is good your best bet would be to take it to a qualified repair shop , that doesn't mean the dealer . Lot of good independant repair shops around , just have to check the yellow pages.
Do you know what DTC'S are ? diagnostic trouble codes ! Not only the ones for the engine management system OBD 2 . There are also DTC'S for the remote keyless entry system , BCM - body control module. You need a factory or professional scan tool to view this codes
DTC B3101
DTC B3102
DTC B3103
DTC B3106

The remote control door lock receiver (RCDLR) communicates with the body control module (BCM) through the keyless entry serial data circuit. When any button on the keyless entry transmitter is pressed, the transmitter sends a signal to the RCDLR. The RCDLR sends a lock, unlock, or panic alarm request to the BCM, depending on which button is pressed on the transmitter. The BCM receives the message and performs the appropriate function. The BCM also uses the keyless entry serial data circuit in order to communicate with the RCDLR when programming transmitters. Do you know what serial data circuits are ?

DTC B3101 Keyless Entry Data Link Circuit Range/Performance
DTC B3102 Keyless Entry Data Link Circuit Low
DTC B3103 Keyless Entry Data Link Circuit High
DTC B3106 Keyless Entry Data Link Parity Error

This is what the factory manual said as to the location of power steering fluid reservoir ! Not much help , you would do better googling it.
The power steering fluid reservoir holds the power steering fluid and may be integral with the power steering pump or remotely located. The following locations are typical locations for the remote reservoir:
• Mounted to the front of the dash panel
• Mounted to the inner fender
• Mounted to a bracket on the engine

anti theft light should blink every few seconds.

try disconnecting the battery for 15 minutes.

Anti-Theft-Perimeter The perimeter anti-theft system consists of the following components:

• anti-theft indicator (THEFT)
• remote anti-theft personality (RAP) module
• hood switch
• keyless entry remote transmitter
• deck lid ajar switch

NOTE: The remote entry features will not function when the ignition switch is in the RUN or ACC position.
Up to four keyless entry remote transmitters (15K601) can be programmed at one time.
The keyless entry remote transmitters :

• Are programmable.
• Must be set at the same time.
• House four buttons.
• House three buttons (Mexico Anti-Theft System only).

Programming
Refer to Section 501-14B.
Inputs and Outputs
The remote anti-theft personality (RAP) module receives input from the following components for anti-theft operation:

• Hood switch.
• Deck lid ajar switch.
• Keyless entry remote transmitter.
• Power door lock switches (LH and RH).
• Door courtesy input.

The RAP module distributes output to the following for the anti-theft system:

• Power door unlock relay.
• Power door lock relay.
• Liftgate unlock relay (Wagon)
• Park lamps relay.
• HORN relay.
• Dome lamp.
• THEFT indicator.
• Deck lid release.

Arming
The anti-theft system can be armed if:

• The ignition switch is in the OFF position.
• The panic alarm is off.
• All doors are closed.

NOTE: If a door is open, the anti-theft system is prearmed and waiting for all the doors to be closed. The THEFT indicator will remain illuminated for up to 30 minutes waiting for all the doors to be closed. If a door remains open after 30 minutes, the THEFT indicator will turn off and the system will return to a disarmed state. After all doors are closed and the 30 second prearm (continuous THEFT indicator illumination) is complete, the system is armed.
NOTE: If the theft LED does not flash after 30 seconds, check the LED FLASH PID to see if the feature is enabled.
The anti-theft system will be armed when the lock button on the keyless entry remote transmitter is pressed, all doors are closed and 30 seconds have elapsed.
When the system is armed, the THEFT indicator will flash quickly until the system is triggered or disarmed.
Disarming
NOTE: Using a key in a door lock cylinder to unlock is not a valid method of disarming the anti-theft system.
Untriggered System
NOTE: If the driver arms the system and remains in the vehicle, an untriggered system can be disarmed by turning the ignition switch to the ON position.
An untriggered alarm system can be disarmed by pressing the unlock button on the keyless entry remote transmitter.
Triggered System
NOTE: If the hood or trunk are open when the system is armed, it must be closed and opened again before it can trigger an alarm.
An armed anti-theft system can be triggered by the following conditions:
The deck lid door, liftgate, hood or any door is opened using a key, inside door handle, hood release, etc.

• The keyless entry remote transmitter can activate a panic alarm which is similar to the anti-theft alarm, but does not cause the THEFT indicator to flash.

A triggered alarm system can be disarmed by:

• Pressing the unlock or panic button on the keyless entry remote transmitter.
• Turning the ignition switch to the ON position.

Alarm State When Battery Power Is Cycled
When the RAP module is supplied power the first time at the vehicle assembly plant, the system will be in the disarmed state. The RAP module will remember whether it is armed, disarmed or triggered in its non-volatile memory. When the battery positive cable is removed and then reconnected, the system will return to the state it was in just before the battery was disconnected. If the system is in any prearm state, then the system will return to a disarmed state when the battery is disconnected and then reconnected.

If it is a factory remote it is either for the trunk release or the "panic" feature. Are the buttons not labeled?

does trunk button work? panic button?
here's 2003 info:

• The doors do not lock/unlock using the remote transmitter

• Remote transmitter.
• Driver door module (DDM).

• Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming

1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.

1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
   Press any button on the transmitter to be programmed.

1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.

1. To exit program mode, turn the ignition to START or wait 7.5 seconds.

--------------------------------------------------------------
report back

Section 13-11: Anti-Theft System, Active 1998 Windstar Workshop Manual DESCRIPTION AND OPERATION Anti-Theft Alarm System NOTE: The system immediately monitors the ignition key lock cylinder upon removal of the key from the ignition. It is not necessary to arm the system for ignition key lock monitoring.

The anti-theft alarm system:

• protects the vehicle from unauthorized entry into the passenger compartment, engine compartment and cargo area.
• monitors the status of the ignition key lock cylinder.
• is controlled by a remote anti-theft personality (RAP) module. The remote anti-theft personality module also controls the electronic door lock functions. Refer to Section 01-14B for more details.
• when armed, detects unauthorized entry into the passenger compartment by using an input from the GEM module regarding the state of the door or liftgate (open or closed).
• protects the engine compartment with a hood switch which is located on the LH cowl vent panel and is part of windshield wiper motor wiring (17A477) .
• triggers an alarm if the ignition lock cylinder is forcibly removed from the steering column.

Once triggered, the system responds by:

• flashing the low beam headlamps, the parklamps, rear lamps and the alarm indicator warning light emitting diode (LED).
• sounding the horn (13832).
• disabling the starter circuit until the system is disarmed.

---------------------------------------------------------------------------------------------
Remote Anti-Theft Personality Module

• The remote anti-theft personality module is located behind the instrument panel (04320).
• It contains a radio receiver that receives the RF signal from the keyless entry remote transmitter (15K601) through the alarm and lock system antenna (15603) and sends the appropriate command to the power door locks, the horn relay, or the generic electronic module.
• The remote anti-theft personality module is equipped with an internal backup power supply which holds the programmed code in memory in the event the vehicle battery is disconnected.

-------------------------------------------------------------------------------
Remote Anti-Theft Personality Module Removal

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove radio. Refer to Section 15-01 .
   

1. Remove lower instrument panel center finish panel. Refer to Section 01-12 .
   

1. Lower glove box.
   

1. Remove two remote anti-theft personality module bracket retaining screws.
   

1. Disconnect electrical connectors and alarm and lock system antenna (15603).
   

1. Remove remote anti-theft personality module and bracket.
   

1. Remove remote anti-theft personality module from mounting bracket.
   

Installation

1. To install, follow removal procedure in reverse order.
   

1. Tighten remote anti-theft personality module bracket retaining screws to 6-8 Nm (54-70 lb-in).
   
   

Components The system is composed of the following components:

• remote anti-theft personality (RAP) module with integral antenna
• alarm indicator LED
• door lock cylinder switch RH, door lock cylinder switch LH
• liftgate door lock cylinder switch (220A40)
• hood switch (part of windshield wiper motor wiring (17A477))
• ignition lock anti-theft switch (19A438)

The following vehicle components are also used by the anti-theft alarm system:

• generic electronic module
• power door lock switch (14028)
• door open warning lamp switch (14018)
• autolamp relay (14N089)
• horn relay and bracket (13853) and horn (13832)
• low beam headlamps
• rear lamps (13404) and parking lamps (13200)
• starter relay
• door lock relays
• keyless entry remote transmitter (15K601)

--------------------------------
Disarming an Untriggered System NOTE: A perimeter alarm will "shut off" after 165 seconds, but the system is still triggered and is not disarmed.

An armed but untriggered perimeter anti-theft system can be disarmed by one of the following four events:

1. Unlock the doors by pressing the keyless entry remote transmitter (15K601) UNLOCK button once.
2. Unlock any door with a key.
3. Turn ignition switch to RUN or ACC.
4. The remote entry PANIC button will disarm the anti-theft system only when the perimeter alarm is triggered and sounding.

------------------------------------------------
System Triggering NOTE: Although the remote entry PANIC alarm is not associated with the monitoring of the vehicle, the user will frequently say that the theft system was triggered when actually the keyless entry remote transmitter PANIC button was inadvertently pressed. A panic alarm will not flash the THEFT indicator.

The alarm can be triggered by the following events if the system has been armed and has not been disarmed first:

• Open any door or liftgate.
• Open the hood (16612) (if the hood was open when the system was armed, it must be closed before it can trigger the alarm).
• Dislodge the ignition key lock cylinder.
• The anti-theft system may be triggered inadvertently when the module is disconnected and then reconnected. To avoid inadvertent alarm triggering, disconnect the smaller 22-way connector first.

When the system is triggered the perimeter alarm will operate as follows: The remote anti-theft personality module will pulse the following outputs at approximately 1.3 Hz, 50 percent duty cycle for two minutes 45 seconds for North America. NOTE: Other perimeter alarms can be programmed for the system.

• low beam headlamps
• parking lamps
• horn
• THEFT indicator

The perimeter alarm can be retriggered, after a perimeter alarm has sounded for 165 seconds. After a perimeter alarm has timed out, if any trigger input is first seen as normal and is then seen in its trigger state, the perimeter alarm will be retriggered. The perimeter alarm can be triggered a total of three times between an arming sequence and a disarm event. An active panic alarm will be deactivated when a perimeter alarm is triggered (a perimeter alarm overrides a panic alarm).

Lock all the doors from the inside (with all the doors closed), unlock your driver's door by manually lifting the lock, then press it back down after you are out - this will prevent the alarm from sounding when you use the key to unlock the door.